OpenSUSE Install :: 11.4 Intel Graphics Error Fixme: Max PWM Is Zero On Boot

Mar 12, 2011

I'm using openSUSE 11.4 KDE upgraded from 11.3. No nonstandard packages that I know of. I get this error messages on boot :

Code:

grzes@opensuse:/etc/init.d> sudo cat /var/log/boot.msg | grep '*ER*'
<3>[ 2.408570] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is zero.
<3>[ 2.665563] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is zero.
<3>[ 2.668069] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is zero.
<3>[ 2.668073] [drm:intel_panel_get_max_backlight] *ERROR* fixme: max PWM is zero.

I was wondering why is this happening. I didn't get those on 11.3.Just to add my openSUSE boots normally and seems to work as expected. My graphics card/driver combo is :

Code:

00:02.0 VGA compatible controller [0300]: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller [8086:2a42] (rev 07)
Subsystem: ASUSTeK Computer Inc. Device [1043:1862]
Kernel driver in use: i915

View 2 Replies


ADVERTISEMENT

OpenSUSE Hardware :: Intel I7 HD Graphics Gives Black Screen Sometimes On Boot Kernel 2.6.37 Rc7

Dec 30, 2010

Just a little background I have a sony vaio VPCZ119X laptop and have been struggling to get all components working under linux especially the intel graphics. I saw that once I upgraded to the latest available kernel release which currently is 2.6.37 rc7. The intel graphics is working, but sometimes when I boot I get a blank/black screen but seems to be lit up. All other functions seem working so for example I am able to login etc just that I dont see anything on the screen.

I have tried the following so far to identify the issue or isolate it:

- Switching to the console screens has no effect, still the black / blank screen.

- Restarting the system does not always immediately get the screen working, sometimes it takes a couple of reboots before the screen is available

- I have a switchable graphics with nVidia I never get this problem when I use the nvidia driver

- I have tried closing the lid etc as suggested in the below post without any change in output, will try further as there are other options available as well The "Black Screen" on Boot I see one difference between both the Xorg log files but I am not able to reason out why this happens hence I will just supply the files here and try not to theorize.

Xorg.0.log - This was the log output when I got the X display working Xorg.o.log.old - This was the log output when the X display was black/blank Also to highlight that I am using the latest kernel release that is still being tested I guess so maybe it is also a bug in the kernel?

View 9 Replies View Related

OpenSUSE Install :: X Not Starting, Intel Graphics Driver?

Jul 16, 2011

I am running Opensuse 11.4 on a file server, based on an Intel Atom motherboard with 945G graphics chipset.I recently shut down and then rebooted the server (because I needed to switch off the power for a few minutes) after it had had been running quite happily for several weeks since the last boot. Now I cannot start X - it gives up after the line(EE) intel(0): failed to set mode: Invalid argumentI've tried googling but am none the wiser what could have caused this, or how to fix it. Excerpts from the X log file:

Code:
[ 229.187]
X.Org X Server 1.9.3

[code].....

View 7 Replies View Related

OpenSUSE Hardware :: 11.3 On Intel Core I5 With Integrated Graphics + Intel H55 Express Chipset

Aug 18, 2010

! I'm thinking of buying a corei5-660 on a motherboard with an Intel H55 Express Chipset. Does anyone know if it's fully compatible with OpenSUSE 11.3? I mean video (that comes from the processor, not an off-board PCI), audio (HD Audio), networking (Intel� 82578DC Gigabit), SATA Controller, USB, etc. I've tried to google but didn't find much info so I wonder if anyone is using or knows where I can find more info about it...

I have found this thread on the forums about the H55 chipset: Core i3 Intel Clarkdale graphic controller problem But the problems were facing on 11.2, I don't know about 11.3...

View 8 Replies View Related

OpenSUSE Hardware :: Intel HD Graphics (Intel Core I3) With Suse 11.3 - Poor Resolution

Jan 2, 2011

I've installed Suse linux 11.3 (kernel 2.6.34.7-0.5) on my brand new computer HP all in one 5130. Everything worked incredibly well : Wifi, wireless keyboard and mouse, sound, webcam.. There is only one remaining issue : I get a very poor resolution (1280x1024) instead of the 1920x1080 allowed by the screen. The graphic card is an intel chipset (HD graphics) integrated to an intel core i3 CPU. Here is (part of) the X11.org log :

Code:
X.org X Server 1.8.0
Release Date: 2010-04-02
[ 15.124] X Protocol Version 11, Revision 0
[ 15.124] Build Operating System: openSUSE SUSE LINUX
[ 15.124] Current Operating System: Linux linux-7xhd 2.6.34.7-0.5-desktop #1 SMP PREEMPT 2010-10-25 08:40:12 +0200 x86_64
[Code]....

View 9 Replies View Related

OpenSUSE Install :: DELL Latitude E6410 - Core I7 M620 With Integrated Intel HD Graphics - Blank Screen

Aug 19, 2010

I have been unable to get both opensuse 11.2 and 11.3 32 bit versions work properly on my DELL Latitude E6410 laptop. With both 11.2 and 11.3 KDE Live CDs I get no graphical display when I attempt to boot into the Live system. VESA mode does not help either, only text mode works. So I installed the system in text mode but during the first boot the screen went blank again.

One peculiar thing is that 11.1 installs and boots fine, what gives? Is this even supported or I shouldn't even try to bother getting this setup to work? Has anyone been able to run opensuse 11.3 on a Core i7 integrated Intel graphics system with X system working?

View 9 Replies View Related

Fedora :: F13 Won't Boot With Intel Graphics?

Aug 18, 2010

i previously posted a thread http:[URL].. that was regarding gaming issue, but now i got a bigger issue. i installed Intel 2010Q2 graphics package from [URL].. i first upgraded xorg-x11-server and related packages and installed devel package using yum.. later i compiled and installed kernel 2.6.34 and other packages included on [URL].. i rebooted the system and it showed display driver unknown so, i used system-config-display --reconfig and it detects my mobile 4 intel chipset. and when i reboot, GUI won't load .. when services finish loading screen goes blank and harddisk light blinks at constant intervals and i can't switch from GUI to CUI either using CTRL + ALT + F2 etc [URL].. PS i am able to login into single user and change xorg.conf

View 6 Replies View Related

Ubuntu :: Error - Fixme:d3d:state_wrap (WINED3DRS_WRAP0) Texture Wrapping Not Yet Supported

Sep 23, 2010

I think this might go for gaming, but maybe a general graphics problem could be taken into consideration for anything else that might display this error:

Code: fixme:d3d:state_wrap (WINED3DRS_WRAP0) Texture wrapping not yet supported. That was spammed in my terminal after I logged into my character. This was spamming itself before logging into my character:
Code:
err:d3d_surface:surface_allocate_surface >>>>>>>>>>>>>>>>> GL_INVALID_VALUE (0x501) from glTexImage2D @ surface.c / 862
err:d3d_surface:surface_allocate_surface >>>>>>>>>>>>>>>>> GL_INVALID_VALUE (0x501) from glTexImage2D @ surface.c / 862

[Code]...

Just to let you all know, I'm not all that advanced in Ubuntu or Linux knowledge, this game is just the only thing keeping me from going completely Ubuntu. I only have Windows installed to play this game, and I've gotten as far as to get this game playing this far,

View 9 Replies View Related

Ubuntu Multimedia :: Boot With Intel Graphics Without Monitor Switched On?

May 12, 2010

i'm trying since ubuntu karmic to set up a xorg.conf for a special purpose. I've a htpc connected to my tv. Intel GMA 4500, DVI->HDMI-cable connected, Lucid Lynx installed. When the machine boots with the TV powered on, everything is perfect. xrandr reports all valid modes on output "DP2". Without the TV powerd on, Lucid starts in the low graphics mode, with the funny zenity-message. So far, i managed to disable all useless outputs (VGA1, HDMI1, DP1, HDMI2), leaving DP2 enabled. I managed this by assigning outputs to monitors and adding Option "Ignore" "True" to the corresponding monitor-sections. My only remaining problem is, that the intel-driver reports no connected monitor on output DP2. The TV is connected, but shut off. Has anyone got a hint to tell the driver to ignore the presence of a monitor?

[Code]...

View 7 Replies View Related

OpenSUSE Install :: Boot With Intel Motherboard?

Jul 3, 2010

I have server with Xeon E5620, 8 GB RAM, three 1TB hard drives which are in sw RAID 5 and two 250GB disk which are in sw RAID 1, all of this on Intel S5500BC motherboard. Installation of opensuse 11.0 11.1 11.2 and Enterprise suse 11 was successfull. After grub menu i get blank screen. It`s blank for about 60 - 120 sec and then appear Suse loading page and loading bar. This also happens if i change to text mod. But in text mod i can see what`s going on. First 5-10 lines are informations about partitions and then i get output just like on this link. Yfrog Image : yfrog.com/5nimag0108djIf i hit any key (in graph and text mode) booting will continue to opensuse loading screen and loading bar.I have tried installations on one workstation and one server and didn`t have this problem.

View 4 Replies View Related

OpenSUSE Install :: Boot - After Installing New Graphics Drivers OpenSUSE 11.4

Jul 14, 2011

I have installed openSUSE 11.4, and I really like it compared to other linux versions I've tried, but I find it requires a bit more linux know-how.

Being fairly new to linux, it has been quite the effort to learn but I started getting the hang of things via online support and such. Lately I've been having some problems.

I need linux to run a TCAD program, and it requires some openGL functionality and was giving me errors when I tried entering the software related modeling GUI.

Anyhow, I thought it had to do with my graphics drivers, so I decided to update them via ATI proprietary driver. After doing this, the system booted me into the console rather than X.

I tried numerous online guides on how to fix the issues, by running all sorts of boot commands (nomodset), and I read the graphics driver theory, as well as trouble shooting ATI graphics.

In the process, I also installed a radeonhd-xorg11-something through YAST, and that caused a black screen altogether upon boot. I managed to boot into failsafe with x, and from there I removed it via YAST, however this did not resolve issues. I also deleted any xorg.cionf files in hopes that the system will default back to the radeon driver.

As it stands right now, I can only boot into my system via failsafe mode. I'm keeping the unit off for now as it's probably tired from all the hard reboots I had to do . If someone can help me resolve this issue, I can turn it on and enter any commands required, such as finding out the graphics card, the kernel, the driver currently running, etc and I can post it here.

View 9 Replies View Related

OpenSUSE Hardware :: Configuring Intel Graphics Driver

Aug 24, 2010

My system occasionally, not often, but enough to bring me to do something about it, keeps freezing. Hard lock-ups. This is a known bug for openSUSE 11.3 and intel video cards. So, I tried some suggestions and updated my kernel to 2.6.35. Nope. Same prob. I updated Xorg, mesa, drm, cairo (had to go to Factory for that one). I finally got all the requirements met as listed on Intel Linux Graphics: 2010Q2 and I download the intel 2d driver, since it's newer than what comes with openSUSE, even in Factory (xorg-x11-driver-video-intel-legacy 2.9.1).Now, when I go to compile the driver, it errors out on ./configure.how do I let this intel driver package know where xorg-server is?

View 3 Replies View Related

OpenSUSE Hardware :: 11.4 And Intel 8xx Graphics Card (i855 Gm)?

Mar 7, 2011

I would like to know if I will be able to work on my laptop with 11.4 , someone knows if something changed with hang/freeze issues? Currently I have installed 11.1 but since repositories were removed no updates or new software for me so I'm considering installing something new.

View 7 Replies View Related

OpenSUSE Hardware :: Multiple With 'Intel' Graphics Driver In 11.4?

Mar 19, 2011

I've been using Mandriva (and predecessors) for ten years or so, but that distro really seems to be dying at the moment. Consequently, I am trying to move over my various PCs to SUSE. I've started with my EEEPC 901 which has a 945GME integrated graphics chip. Using Mandriva 2010.2 it works fine and I can have desktop effects (built into KDE) running with no problems. However, with KDE on openSUSE 11.4 I get irregular freezes, although I can still work within the focussed window. Moving around though, clicking on other parts of the desktop etc. doesn't work, then after a few seconds they all happen at once. I am getting the following error multiple times in the X log, which I suspect is associated:

Code:
EQ overflowing. The server is probably stuck in an infinite
loop.

I note this supposedly fixed bug report that may be relevant:[URL].. Secondly, I am getting hopeless 3D speed (glxinfo reports SGI and has all expected output). Desktop effects won't work at all, on boot it pops up a message saying they are disabled as too slow. I know it isn't a benchmark, but glxgears gives about 50, it used to give over 500. I remember a few X versions back having to enable UXA mode instead of EXA in the 'intel' driver, but presumably that is no longer needed and I cannot see any effect of doing that now (in the xorg.conf.d device file). According to the X log, X is definitely using 'intel' driver, not fb etc.

View 9 Replies View Related

OpenSUSE Hardware :: Driver For Intel Core I3 Integrated Graphics?

Nov 25, 2010

As this seems not yet to be covered in openSUSE Graphic Card Practical Theory Guide for Users I am asking here.

The Motherboard is an Asus P7H55-M Pro with Intel Core i3 530@2.93GHz. openSUSE 11.3 assigns the i915 driver by default:

Code:
# lspci -vk
00:02.0 VGA compatible controller: Intel Corporation Core Processor Integrated Graphics Controller (rev 12) (prog-if 00 [VGA controller])
Subsystem: ASUSTeK Computer Inc. Device 8383
Flags: bus master, fast devsel, latency 0, IRQ 30
code....

View 9 Replies View Related

OpenSUSE Multimedia :: Choppy Video With Intel HD 3000 Graphics?

Aug 19, 2011

I recently installed openSUSE on a new Toshiba and i'm getting very choppy video while watching videos on ....., justin.tv, etc. The video is fine as long as I don't full screen. However, when I try to fullscreen a stream on justin.tv or a ..... video, it instantly becomes choppy and video is extremely delayed in relation to the sound. The sound still continues at it's regular pace, however the video lags behind and is just choppy in general.Also, not sure if this helps, but i'm running an i3 2310M.

View 5 Replies View Related

Fedora Hardware :: Intel Graphics Card - Enable Desktop Effects - Graphics Just Crashes And Freezes

Jan 27, 2011

I have been trying to enable compiz on my fedora 14, but when i enable the desktop effects the graphics just crashes and fedora freezes. When i type lspci -nnk | grep VGA for the graphics card i get:

I made alot of research on how to get Intel graphics work on Fedora, but couldnt find any solution

Same problem I had with Fedora Core 12 and 13.

View 5 Replies View Related

Debian Installation :: X Server Crashes On New Install On Intel I855 Graphics Card

Sep 13, 2010

I have just reinstalled testing on a Samsung Q30 and I cant get X to start. I am just left with a blank screen and ctrl+alt+Fn does nothing. I had a previous install of testing that worked fine but it might have been running a previous version of the kernel, or I had installed a bug fix to do with 915resoultion that I can't remember about. Booting off a Slax live cd works fine but I have had similar problems with Knoppix and Ubuntu.

I am running LXDE but I previously tried Gnome and had the same problem. Running xander displays cant open display Running dpkg-reconfigure xserver-xorg returns nothing, as does Xfree86 -configure There is no /etc/X11/xorg.conf or installed by default, I have tried running startx with a custom xorg.conf and the automatically generated one from -configure. The automatic one did not include any resolutions and was configured for a dual head set up although there was only one monitor connected.

I thought it may be the same problem as this:[url]

But I have tried following the bug fixes on that site and I have had no luck.

lspci

Xorg.0.log

View 1 Replies View Related

Fedora Installation :: Can't Install FC10 Or FC11 For Desktop With Intel GMA X4500HD Graphics - Screen Goes Black

Jul 20, 2009

I cannot install FC11 or FC10 on my Dell XPS One/A2420 machine. Every time I tried to install the Linux operating system, the screen goes black and the computer goes no response. It seems to have something to do with the video card--Intel GMA X4500HD Graphics.

View 1 Replies View Related

OpenSUSE Hardware :: Ubuntu Edgy On Intel 945GM Graphics & Wide Screen LCD NoteBooks - Resolution Limited To 800x600

Mar 12, 2010

I'm stuck at 800x600, and no matter what i try i seem to hit a dead end. I've got the Intel Mobile 945GM/GMS rev 03, and it seems like lots of people have had to fiddle to get it working. Here's the info I've collected and tried so far. Ubuntu Edgy On Intel 945GM Graphics & Wide Screen LCD NoteBooks � 100% Linux Addict

HOWTO: install drivers and set up widescreen res. with Intel 945 vga card and Ubuntu - Ubuntu Forums Mostly Harmless: SuSE, Acer aspire 5580 and non-standard resolution 1280x800 Intel 945gm And 1280x800 Laptop Monitor Problem Suse 10.2 - openSUSE Forums I'm not too proficient with linux yet, so the right solution might be here and I'm just not getting it right. Maybe i'm not on the right path at all.

View 9 Replies View Related

OpenSUSE Install :: 128 Gb Boot Error / Installation Froze At 92% And After The Laptop Wouldn't Boot?

Nov 23, 2010

I tried to install 11.3 on my acer aspire 7530 notebook to have dual boot with xp.

I made 4 partitions: one for xp, and the three for linux were made automatically.Before installation I got the warning that the partition wasn't entirely below 128 gb, I installed anyway to give it a try.

The installation froze at 92% and after the laptop wouldn't boot.

Now I've formatted the hard disk and installed windows on a partition leaving a free un formatted partition of 100 gb.

View 9 Replies View Related

OpenSUSE Hardware :: Video With 11.4 32 Bit & The Intel 865 Graphics Controller - Disable "Desktop Effects"/XGL/compiz?

May 1, 2011

Just put 11.4, 32 bit on a system with an Intel D865 GLC motherboard and 865G built in graphics controller. While the install went OK it turns out that X is totally hosed. After fighting with things for a while and discovering that Sax2 had disappeared I poked at Google and discovered some other poor folks that have had similar issues with Intel video cards. Based on a suggestion for a doc in OpenSuse.org I edited the file: /etc/X11/xorg.conf.d/50-device.conf

and added the line: Driver "intel" to it - after that things got better. Obviously the install process had not identified the video card correctly. I'm now left with another issue - while the system now identifies the driver and can talk to the monitor correctly, a Samsung S23A350H I can't open a window after X comes up and I login - basically the same issue as the unresolved Bug 673873: [Bug 673873] intel [865G] Windows flash rapidly or don't appear if Desktop Effects are on in KDE and GNOME

The workaround is to turn Desktop Effects off but since X doesn't work I can't figure out how to do that. I can't find the gnome-xgl-switch or a xgl-switch that used to exist to do it on the command line so that's out. Someone said you could drop the empty file "disable-compiz" in the ~/.config/compiz directory and that would do it but in 11.4 that directory doesn't exist. how to disable "Desktop Effects"/XGL/compiz or whatever it is now called on the command line in OpenSuse 11.4 without a gui if that is still possible?

View 6 Replies View Related

OpenSUSE Install :: Error After Boot \ When Start The System, Opensuse Is Not Open With This Lines?

Jul 4, 2011

I set up opensuse 11.4. I updated nvidia 6600 drivers from vendor. Everything is good until automatic kernel update. When I start the system, opensuse is not open with this lines.

/etc/rc.status: line 1: /bin/ash : no such file or directory
bash: ./etc/sysconfig/chron : cannot execute binary file
X_MOUSE_CURSOR : Undefined variable

[code]....

View 3 Replies View Related

OpenSUSE Install :: Clean Install 11.4 Dual Boot System Grub Error?

Apr 27, 2011

I did a fresh install of SuSE 11.4 (WIN7 TOO) and changed my Larger HD1 to the first HD. I was installing and got this error first: the boot loader is installed on a partition that does not lie entirely below 128GB The system might not boot if BIOS supports only lba24 (result is error during install grub mbr) status loc dev/sdb6

I continued with the install and then got:

Yast2 error occured
while installing GRUB ver 0.97 (640k lower/3072k upper memory)
[minimal bash-like lineediting is supported? for the first word, TAB lists possible command completition anywhere else TAB lists possible completion of a device/filename]
grub setup --stage2=/boot/grub/stage2 --force4-lba (hd0,5) (hd0,5)
Error 25
disk read error
grub> quit

View 9 Replies View Related

Ubuntu Multimedia :: Dual Boot Up And Low Graphics Mode Error

May 26, 2011

I have a dual boot xp -ubuntu - AGP ati 2600 series radeon. Intel 8300 dell. The message comes up after login "ubuntu is running in low-graphics mode". I hit ok and I get 5 choices and none of them work.

1) run ubuntu in low-graphics mode.
2) reconfigure graphics.
3) troubleshoot the error.
4) exit to console login.
5) restart X.

View 5 Replies View Related

OpenSUSE Install :: KDE To Boot From A USB Key - Getting Error 17

Feb 20, 2011

Trying to get an OpenSuse Live KDE to boot from a USB Key and I'm getting error 17 messages. I get no Grub boot screen or access to any of the grub functions so I'm stuck. BIOS has been changed to allow booting from USB so no issue there. If I remove the USB key and boot from HDD I have no problems dual booting either Linux or Windows using Grub.

View 3 Replies View Related

OpenSUSE Install :: ACPI Error On Boot

Dec 26, 2009

After upgrading to 11.2 my laptop HP dv9000 I'm getting some errors:

ACPI Error (psargs-0359): [2012] Namespace lookup failure, AE_NOT_FOUND
ACPI Error (psparse-0537): Method parse/execution failed [\_SB_.PCI0._OSC] (Node ffff88007fbf45f0), AE_NOT_FOUND

View 3 Replies View Related

OpenSUSE Install :: Boot Error Following Upgrade To 11.4?

May 7, 2011

I upgraded to OpenSuse 11.4, and I am getting the following error message on boot:fsck.ext3 -a -c0 /dev/sdb2Bad magic number in super-block while trying to open /dev/sdb2The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid andreally contains an ext2 filesystem (and not swap or ufs or something else), then superblock is corrupt and might try running e2fsck with an alternate superblock:

e2fsck -b 183 <device>
fsck failed. Mounting root device read only.
mounting root /dev/sdb2

[code]....

View 2 Replies View Related

OpenSUSE Install :: 11.3 - Red Error: "the Boot Loader Installed On A Partition That Does Not Lie Entirely Blew 128 GB .The System Maight Not Boot"

Mar 29, 2011

i want to install opensuse on my new lap top i partition my hard (600gb) with 5 parts:

c: 97 gb
d: 150 gb
e: 150 gb
f: 100 gb
g: 50 gb
and 38 gb unlocated part

in opensuse instalation , the yast makes a 2gb for swap 14gb = root , 21 gb = home, but in Instalation Overview under Booting has a red error: the Boot loader Installed On a Partition that does not Lie Entirely Blew 128 GB .The system maight Not Boot;

View 1 Replies View Related

OpenSUSE Install :: Upgrade To 11.2 - Filesystem Error On Boot ?

Nov 23, 2009

Upgraded from 11.1 to 11.2 using GUI (YaST and Wagon)

Machine stops on boot and says:

fsck failed. Please repair manually and reboot. The root file system is currently mounted read-only. To remount it read-write do: bash# mount -n -o remount, rw /

Attention: Only CONTROL-D will reboot the system in this maintenance mode. shutdown or reboot will not work.

Give root password for login:

I write: mount -n -o remount,rw /

And then reboot with CONTROL-D.

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved