Networking :: Configure A CDC Ethernet Device ( A 4g USB Dongle)

Oct 2, 2010

I have a usb 4G dongle which has stated no linux support in australia from vividwireless.

The flip flop part does not exist for me in the sense I can not see the cd autorun files so I downloaded the files off the net and put them in my wine directory

I attempted to run the exe file thru wine but whether I try graphical or command line....it defaults to a graphical dialog box....I click on English...installer then shows the dialog box for the welcome screen ...then I click on next and the screen shows for a nanosecond the user agreement but exits with no log etc.

2) so in linux here is the info

Code:
Bus 001 Device 020: ID 12d1:380b Huawei Technologies Co., Ltd. but when I press lsusb again....that info disappears....hmmm

ok so

Code:
Oct 3 06:42:35 sid rsyslogd: [origin software="rsyslogd" swVersion="4.6.4" x-pid="1435" x-info="http://www.rsyslog.com"] rsyslogd was HUPed, type 'lightweight'.
Oct 3 07:00:15 sid kernel: usb 1-8: new high speed USB device using ehci_hcd and address 3

[Code]....

View 9 Replies


ADVERTISEMENT

Ubuntu Networking :: Use 3G USB Modem Dongle And Ethernet Network At Same Time

Feb 24, 2010

I currently have a computer sitting underneath a router/switch on a Local Area Network that I want to connect to the Internet using a 3G USB dongle modem. If I am connected to the ethernet and then enable the modem connection, only the ethernet LAN side works. If I enable the modem and then enable a (disabled) ethernet connection, only the ethernet LAN side works. If I keep the ethernet disabled and connect using the modem, I can get out onto the Internet, but obviously not the LAN. I need to be able to do both.

View 2 Replies View Related

Ubuntu Networking :: No Ethernet Device At All?

Jul 9, 2010

I just installed 10.04 on a Dell C800 and I've been trying to connect to the internet via Ethernet with no avail. I did some searching and ran lspci -nn and got this:

user@user-desktop:~$ lspci -nn
00:00.0 Host bridge [0600]: Intel Corporation 82815 815 Chipset Host Bridge and Memory Controller Hub [8086:1130] (rev 02)

[code]....

View 1 Replies View Related

Networking :: PCI Device And Ethernet Adapter Relation?

May 20, 2010

I have two pci network adapters. I see them in pci device list (lspci). And I see them using ifconfig. How do I relate them - which pci device corresponds to ifconfig network adapter ? (I can't open my hardware and relate them using MAC stickers)

View 4 Replies View Related

Networking :: Configure Ethernet Connection Between 2 Fedora 12 Pcs?

Mar 5, 2010

I want to connect my pc to my laptop. I have fedora 12 installed in both system.How can I do this?

View 14 Replies View Related

Networking :: Configure My Ethernet Card To Work?

Sep 2, 2010

Tell me how to configure my Ethernet card to work. My pc only works wirelessly. I don't know what kind of Ethernet card is installed. I have Ubuntu 10.4 on a dell pc 1ghz, 20ghd, 512mb.

View 2 Replies View Related

Ubuntu Networking :: No Ethernet Connection Recognized - No Such Device

Jun 17, 2010

I just installed 10.04 on my new netbook and I am suprised to see that the ethernet is not recognized. When I run

Code:

ifconfig eth0

the result is

Code:

no such device

The machine was working fine before I installed Ubuntu. I am suprised to see this problem as I have already installed it on a few machines without any problem such as this.

View 2 Replies View Related

Ubuntu Networking :: Find A Device Connected Via Ethernet?

Nov 12, 2010

I have a device (not a pc) connected to my pc via ethernet, it dose not show up in networks, I was hoping there was a way of scanning to detect for it, is there a way of seeing content of it is basically what I'm asking?

View 5 Replies View Related

Ubuntu Networking :: Usb To Ethernet Device Not Detected / Enable This?

Jul 28, 2011

I'm using ubuntu 10.04 enterprise cloud server for my project. I use USB NIC to interface with other 2 servers. but the system doesnot detect USB NIC. detect & configure USB NIC in the network.

View 5 Replies View Related

Networking :: Ethernet Interfaces - Device Activated On Reboot

Dec 28, 2010

The ethernet configuration files are under
"/etc/sysconfig/network-scripts" such as "ifcfg-eth0:1" etc.

The file looks as follow:
Code:
DEVICE="eth0:1"
BOOTPROTO="static"
ONBOOT=no
IPADDR="172.23.17.10"
NETMASK="255.255.255.0"
ALIAS="yes"

I've set the ONBOOT=no. This means this device should not be activated at boot-time. But as I reboot the machine, this device is activated again. This means the option ONBOOT doesn't work. Seems this is a bug of RedHat LINUX?

View 3 Replies View Related

Ubuntu Networking :: VMWare Workstation 7 On 9.10 - Can't Find Ethernet Device

Aug 29, 2010

I just upgraded to VMWare workstation 7. I was previously running v.6, and an older linux version, and everything was working fine. I moved over the same VM files to the new computer, and it doesn't find the ethernet connection. When I start up the virtual machine, I get an error message:

Could not connect Ethernet0 to virtual network "/dev/vmnet8". More information can be found in the vmware.log file.

There log file doesn't say much more:

Jan 07 17:31:36.928: vcpu-0| VNET: MACVNetPortOpenDevice: Ethernet0: can't open vmnet device (No such device or address)
Jan 07 17:31:36.928: vcpu-0| VNET: MACVNetPort_Connect: Ethernet0: can't open data fd

[code]....

Once xp has booted, I get the "new hardware" wizard, saying that it found an ethernet adapter. However, it can't find any driver for it. I think this dialog started appearing after I added a new virtual network entry using the "Virtual Network Editor". Originally I didn't even have a /dev/vmnet8 file. Now I do.

View 2 Replies View Related

Ubuntu Networking :: Configure Second Ethernet Card For A Dhcp/dns Server?

Mar 2, 2010

i already have an eth0 configured to automatically get its info from dhcp.

but i wanna configure eth1 to be able to serve dhcp and dns. i havent configured either dns or dhcp server on the server box since i have not configured the serving interface.

so far my interfaces file is:

Code:
# The loopback network interface
auto lo
iface lo inet loopback
# The primary network interface
auto eth0
iface eth0 inet dhcp

[Code]....

View 1 Replies View Related

Debian Hardware :: Wired Ethernet Dongle Drops Connection

May 2, 2015

I'm using a wired ethernet dongle due to my machine not having an ethernet port, however it sometimes drop connection, how can I diagnose whether if the dongle is faulty or my system is having trouble maintaining a connection.

View 14 Replies View Related

Networking :: Increase Storage Space Of Server With NAS/DAS Device Via Gigabit Ethernet?

Feb 8, 2010

Cost effective (the people want cheap) solution to increase server storage space with as little impact on throughput (what I want) as possible. I have a server that sends instructions to 20 clients to perform certain tasks. The clients send gigs of data back to the server for storage.

BACKGROUND INFORMATION
Network: Gigabit Ethernet
Clients: (20) HP, Solaris, Linux
Linux Server: Dell R805 PowerEdge (QUAD Core Athlons 16 gigs of ram, 4 gigabit ports.

Selected directories are mounted (NFS) by clients. One directory to be mounted by the clients contains executable files. Mount commands are sent from the server (rsh) to the clients. Yes I know (ssh) but this is how the software was originally written so let's go with it.

The clients then receive commands to execute the binaries contained within the mounted directory. The binaries basically create an image of the clients filesystem including special applications. The client then sends the files and directories to the server which stores this �image�. This process can be reversed to restore a client to the initial baseline image.

In a nut shell, 20 clients are sending gigs of data to the server for storage. I need to attach a NAS (gigabit) to extend the storage capability of the server. The server would mount (NFS) to the hard drives on the NAS. The NAS, configured as a �direct attached storage� device (DAS), means the storage device is connected directly to the server and not the network (which makes it a DAS). This would provide direct storage expansion for the server. However, this configuration cannot be a bottleneck that significantly hinders performance.

Clients <---data---->Server<----storage---->DAS/NAS

1) Will a low end NAS (gigabit port) work? (NetGear 1TB ReadyNAS Duo, RND2110-100NAS) or something with a higher rated throughput (QNAP TS-239 Pro II)

2) Low end won't work, go with �?

3) Does the processor on the NAS play any role that would determine the performance of this configuration given that the server would mount directly to a directory on this device (DAS/NAS)?

View 7 Replies View Related

Ubuntu Networking :: Error Ethernet Controller Is BROADCOM Corporation Device 1692 ( Rev 01)

Dec 1, 2010

I am not able to configure ubuntu 9.04 on network ,

i get error Network UNCLAIMED. error ethernet controller is BROADCOM Corporation Device 1692 ( rev 01)

View 3 Replies View Related

Networking :: Slackware 13 64bit - Nvidia Forcedeth Module - Can't Load - No Ethernet Device

Feb 15, 2010

64bit Slack doesn't recognize my ethernet device. ifconfig -a show no eth0. It's an onboard nvidia MCP55 ethernet nic. Never had this problem using 32 bit Slack.

When I try to modprobe forcedeth I get the following error:

repeats those two statements 3 times

I just recompiled my kernel with every possible 10/100 ethernet device included in the modules. Still no go.

View 3 Replies View Related

Ubuntu Networking :: Configure OS Version 9.1 Laptop To Vwork With Device

Jan 19, 2010

I have a Netgear wgps606 wireless print server with a 4 port switch. My question is how do I configure my ubuntu 9.1 laptop to vwork with this device.

View 6 Replies View Related

Networking :: Unable To Configure The Network Card Because The Kernel Device Is Not Present

Jan 28, 2010

I have installed Linux SuSE 10.3 on a PC (Lenovo Thinkstation A58). However, when I start the computer I get the following error message:

"No valid Host_ID or host-name found."

I then use YaST to set up the network. I get the following error message:

"Unable to configure the network card because the kernel device is not present."

The computer has Windows 7 installed and everything seems to work fine. The LED on the Ethernetplug is blinking when using Windows, but not when using Linux. I guess this means that there is no driver for the Ethernet card (Marvell Yukon 88E8057). I have not found any driver for the card and am considering buying a new one. Which PCI card works with SuSE Linux 10.3?

View 1 Replies View Related

Fedora Networking :: Configure ADSL Using Use Fc10 - Ethernet Cable <Asus Am608 ADSL Modem>

Aug 6, 2009

I want to configure my ADSL but I don't know what should I do. Can you explain me How can I configure it?(I use fc10, ethernet cable <Asus Am608 ADSL modem)

View 9 Replies View Related

Ubuntu Networking :: User Interface Changed And It Defaulted To Ethernet And Now It Won't Letting To Go Back On Wireless - Disable Ethernet?

Sep 1, 2011

My laptop was working fine on wireless till the userinterface changed and it defaulted to ethernet and now it won't let me go back on wireless How do i disable ethernet?

View 4 Replies View Related

Hardware :: Connecting USB 3G Dongle Device As "modem"

Dec 26, 2010

connecting a 3G USB dongle device, that works with a SIM card, perhaps via wicd as the network manager. I have it working under Windows 7 and the following are some of its details:

Code:

Device Name : ZTE Proprietary USB Modem
DeviceType : Modem
Authentication : CHAP

[code]....

View 14 Replies View Related

Red Hat / Fedora :: How To Configure Ethernet Card

Dec 10, 2010

I have installed linux on my system. I have connected two ethernet cards in the CPU. I have then connected one cord to one card from the modem. Its working fine. I have connected another cord from the second port to the switch and there by from switch to other systems. However the system is not detecting the second card. I am a newbie to linux and I don't know how to configure it.

View 3 Replies View Related

OpenSUSE :: Terminal Access To A Ethernet Device

Feb 24, 2011

I know that there is support for this, but i can't seem to find any appropriate tools. Let's say my widget is at 192.168.1.111; i need to open a terminal window talking to it. Then i can control the things connected to it (it is a bus converter). oS 11.1, KDE 3.5, various machines.

View 2 Replies View Related

Server :: Configure Two Ethernet Cards With The Same IP For Redundency?

Jul 20, 2010

how to configure two Ethernet Cards with the same IP for Redundency and Load Balancing?

I appriciate if you spare some time on replying by above query.

View 1 Replies View Related

Debian Hardware :: Ethernet Device Appears And Disappears

Mar 12, 2010

Brand new Acer laptop | Intel chipset
Ethernet controller: Attansic Technology Corp. Device 1063 (rev c0)

During this week, I installed Debian twice on this system using NetInst, connected trough ethernet. Yesterday, I noticed the ethernet controller wasn't listed by lspci. I restarted, it appeared but didn't work. I turned off the system, started it a bit later and the device worked normally. This odd behavior has happened during the last twenty four hours. The ethernet controller appears and disappears. I enabled the "Boot from LAN" BIOS option to check the availability of the device right upon start and I'd say there's a 50% chance that it doesn't appear. I posted this message connected through the ethernet device.

I guess I should return the laptop because of this problem but I know very little about hardware and I wanted to ask first.

View 5 Replies View Related

Debian Hardware :: Connecting To Device With Ethernet Card

Mar 18, 2011

I just did a fresh install of Squeeze with a KDE desktop on my computer. I use this computer to run an instrument in my lab. The instrument is connected to my computer through an ethernet card. Since my reinstall I cannot figure out how to get my computer and instrument communicating again. I'm guessing that I need to somehow tell my computer to connect to the device, but I don't know how. Here is my interface configuration:

[Code].....

I think my instrument is connected to eth2, which does not show any inet addr or Bcast ip, so I'm guessing that is a problem. How do I fix this?

View 9 Replies View Related

OpenSUSE Network :: No Ethernet Device After Installing Updates?

May 26, 2011

I'm currently using SuSE 11.4 and after running the full online updates and restarting the machine as YAST suggested, I no longer have eth0/eth1 available.

I'm clueless about what to do since I'm kinda new to Linux and at the moment, I'm trying out all the distros before making a full commitment to anyone. So far, Ubuntu has been trouble-free from day one, but I'm willing to give this distro (opensuse) some slack.

View 9 Replies View Related

General :: How To Call Ethernet Card - By Device Name Or Nick Name ?

Jun 23, 2010

I want to know that in my Linux box under "Network Configuration....>Devices" i can see Device eth1 and Nickname eth0.

The ambiguity in my mind is when we want to down network interface we should call it by device name or nick name

Example

Or

Code:

View 4 Replies View Related

Slackware :: 64 13.1 Attansic NIC - Dell Inspiron R17(N7010) - No Ethernet Device

Dec 26, 2010

Just installed slackware64 13.1 and there is no ethernet device... lspci: Ethernet controller: Attansic Technology Corp. Device 2060 (rev c1)

View 8 Replies View Related

Slackware :: Configure Old Desktop With 12 As A Router And Ethernet Card RTL 8029

Jul 2, 2010

I am really interested to configure my old desktop with Slackware 12 as a router. But unfortunately I did not found any other ethernet card (second) as Realtek 8029. (I need two ethernet cards according to the howto [URL]) It is possible to get up and running this card? I was googling a lot. I tried to use the ne2k-pci module. It seems that it was loaded successfully, but I cannot see my interface (eth1) with ifconfig.

lspci shows:
Quote:
00:0b:0 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8029(AS)
lsmod:
Quote:
ne2k-pci 12768 0 (used by)
[Code]....

View 6 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved