I'm new to Ubuntu. Today, I took my old Compaq Presario V3010US and gave it life with Ubuntu 10.04. The hard drive was erased and replaced with the Linux OS stuff. Ubuntu recognizes most of the hardware except my Broadcom wireless card. I find this to be a pain because i'm a newbie to linux stuff. Anyway, can anyone help me fix this? I thank you for your time reading this.
View 1 RepliesJust installed Fedora 14 from the Live CD i686 on my Dell Inspiron 1521. I can't connect to the SpeedTouch 585 on either wireless broadcom card or the wired Ethernet card.
I can connect to it from the same Laptop on the Vista which is on dual boot on the same laptop.
Further confusing is that I ran Fedora 14 and connected to another SpeedTouch today.
Already checked the Channel on the wireless nic and it's on the same one as the SpeedTouch.
I have a Broadcom BCM4311 wireless card on my Dell D620 laptop.
Code:
09:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5755M Gigabit Ethernet PCI Express (rev 02)
0c:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01)
My wireless works perfectly with my university networks. But I have problem connecting to my house router. The first time I installed Ubuntu 10.10, it connected to internet and worked well. After a restart needed by nVidia driver, my house wireless stopped working while my university wireless still works. I have tried reinstalling the driver using System/Administration/Additional Drivers and manually
Code:
sudo apt-get update
sudo apt-get --reinstall install bcmwl-kernel-source
Ever since I upgraded to the new Ubuntu, I have been having problem with wireless. In the "Hardware Drivers" I come up with 2 drivers:
1) Boadcom B43 wireless driver
2) Broadcon STA wireless driver
I activated the first one, but latter noticed that the wireless was not working, so I tried installing the second and it returned this message:
Quote:
So I unactivated the first and then it disappeared leaving me with the second, and its error message.
Quote:
What should I do now?
The output for "lshw -C network":
Code:
The last few pages of /var/log/jockey.log.
Code:
I am new to Ubuntu and have just installed Ubuntu 10.04 on a Dell D600. My wired network is working perfectly however, my wireless card is unable to detect wireless networks. I am using a Broadcom Corporation BCM4306 wireless card. I have updated the drivers and it is installed correctly as far as I can tell. My card seems to be working, but it doesn't detect any wireless networks. I know that my wireless is functioning, because I can log on successfully with a windows laptop. In addition there are 5 or 6 other networks available, so it should be able to detect something. I am new, so please let me know what information you need and, if possible, how to find it.
Here is the results of "lshw -C network" from the terminal below:
mikee@mikee-laptop:~$ lshw -C network
WARNING: you should run this program as super-user.
*-network:0
description: Ethernet interface
product: NetXtreme BCM5705M Gigabit Ethernet
vendor: Broadcom Corporation
[Code]...
I chose to change my operating system from Microsoft Xp to Linux and finally chose Fedora to be my new OS.
After Fedora installation I got a problem that I cannot connect to my wireless network I used to using Xp, I think that my wireless card is not installed on Fedora because when I checked in the network configuration I found that the only installed adapter is the Ethernet Realtek for the wired connection.
My OS is Fedora 11.
The CPU Model name is : Intel (R) Core (TM) 2 Duo CPU T8300 @2.40 GHz, so I think that my architecture is x86_64.
My Network controller is : Broadcom Corporation BCM4312 802.11b/g
I just installed 9.10 and I can't detect any wireless networks. Is the card compatible with 9.10? Do I need to install any drivers? If the card isn't compatible with 9.10 is it compatible with later versions of Ubuntu? Marking this as somewhat urgent as I need to get internet access for some coursework soon, and also because my parents will kill me if they find out I've done anything unusual with the laptop because it's new and they think anything non -MS is a virus.
View 9 Replies View RelatedI have a DEll Mini 9 - it has worked fine even though it has a limited memory. But Husband only uses to have a surf. It now wont connect to net. The Broadcom4312 Wireless Card is not working on Obunto. It has a Dell 802.11b/g Wireless LAN Mini card installed and Obunto Edition Version 8.04 Have phoned Dell and after several calls on Hold for over 15 mins each time and getting nowhere fast i am coming to you guys/girls. I am not a very good comp person, but i do get by and i am trying, so be gentle with me. in simplistic terms.
View 2 Replies View Relatedi'm running ubuntu 10.04. i've followed these instructions:[URL]that got the light for the wireless on my laptop to light up but it doesn't seem to be able to find any networks.when i click on "connect to hidden wireless network" and enter the details + encryption code. it spends a few minutes trying to connect before asking for my encryption code again but i know that the code i entered is right.i'm using a belkin router with wpa/wpa2 encryption. but i think it's a problem with the wireless on my laptop rather than a problem with my specific network because under windows on other machines in my house i can see some of my Neighbours networks
View 2 Replies View RelatedI just installed Lucid Lynx on my Dell Vostro 1000 laptop. The problem I'm having is that my wired network card has died on me prior to installation. I'm having the hardest time finding the required files to make my Broadcom BCM4311 wireless card work without being able to download any packages from the web. If anyone knows which files I need and which order I should use to install them that would be great.
View 5 Replies View RelatedI have an HP mini 110 with Fedora 11 install. I installed the broadcom-wl and wl-kmod from yum but still no wireless. First I can't get the broadcom card to turn on using the slide switch on the front of the computer. The device is inactive in the network configuration-devices window. The card is not in the network configuration hardware window. When I try to add it manually, there is no entry for the card in the drop down list. I am new to Fedora but have used linux for years. Unfortunately this is my first attempt at wireless networking.
The posts and google stuff doesn't say much more than "yum install broadcom-wl" Can anyone point me into the right direction? I have a feeling I am missing something very simple, because this computer dual boots Linux Mint and wireless works flawlessly.
I recently installed Ubuntu x64 on my dell studio 1535 using the windows installer (wubi).
All seems to be working fine apart from the built in wireless card, the proprietary driver (found in hardware drivers) installs and activates successfully and works perfectly. Until I shut down or restart the system. On the next boot the wireless card is 'disabled' and no longer works.
The card I have is a Broadcom Corporation BCM4312 802.11b/g
I am going to try a proper install on a second partition rather than using wubi later on but wondered if this was a commonly occuring problem?
The wireless card works as soon as the driver installs, however I am shown a "restart to activate driver" message and after restarting it's dead.
when it comes to openSUSE but I am earnestly trying. I installed the openSUSE OS on my HP dv6000 laptop, but it does not seem to recognize my wireless card (which is a Broadcom 4311).
View 7 Replies View RelatedI know some wireless card can work in Master Mode but it seems use madwifi driver. I know madwifi doesn't support usb dongles find a usb wireless card which can work as AP under Ubuntu. I have check this list [URL] I am not sure if ar9170usb.ko and its device support Master MOde.
View 6 Replies View Relatedive just installed the aircrack package in my dell vostro 1310 which i bought with its ordinary wireless card ( hell knows what it is. couldn't find..).At the very first time while trying to reach my wireless internet i was using backtrack 4 and i was not sucesfull.. that would be good normally, but it was not. because i couldnt do it cuz my wireless card wasnt being recognized by airmon..so i tought..i can use my wireless with ubuntu... then i got ubuntu again.. and intalled the aircrack.. as i run it i found ou t that still it wont find my wireless card...do i need any further config. to make it work with aircrack ??i can only find eth0, which is my wired network device....
View 1 Replies View Relateddell laptop and went out on thenet looking for a solution for my failed wireless interface. i downloaded the firmware but then my interface still fails to come on after a reboot.
wlan0 IEEE 802.11bg ESSID:""
Mode:Managed Frequency:2.412 GHz Access Point: Not-Associated
Tx-Power=0 dBm
[code]...
Any opinions on which of the PCMCIA wireless cards work the best out of the box? I currently have a USB wireless adapter but want to get rid of it and use my PCI slot on the laptop. I am currently running lucid. I would rather not have to mess around with NDISWRAPPER again, something that has a native linux driver would be great.
View 2 Replies View RelatedI have been running F13 since it came out, with the wireless working fine since I got it working (using the RPM Fusion repository, broadcom-wl-5.60.48.36-1.fc13). Since I updated software (without reading what was to be updated), yesterday, I am unable to even find wireless networks, although I am, as you can see, able to access through eth0 It is not a hardware problem, as I can not only find them, but access them on Ubuntu 9.10 live disc. Below is my lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
[code].....
I have been trying to find a wireless card that will readily work with Ubuntu 10.04 Desktop. Preferably an +802.11 N with an indoor range of between 300 to 400 ft. with possibly two antennas. Am finding many that say linux on the box but find that it ain't so. Also most times with no instructions or very convoluted process that results in errors.
View 1 Replies View RelatedAluminum Unibody macbook, the only aluminum macbook to date. It has a Broadcom chip in it and I installed the STA drivers. The first day it seemed to work fine. Then I noticed pages stopped loading. The max throughput I get is like 30KiB/s once in a while. Sometimes I see consistent speeds of 600B/S...this really sucks. Is there a fix or anything?
I was going to make the switch slowly to 10.10 full-time, but the wireless issue is bothering me. The keyboard brightness keys don't work natively, but there's a fix I saw but didn't have time to implement earlier. I like ubuntu but I don't like my wireless not working!
I decided to start of with Debian. I'm having trouble getting my wireless connection to work. I think i need drivers or something, i can't make a wireless connection. And it is a bit difficult for me, as i am new to Linux, and I'm not sure what I'm doing when i am writing these commands.
My wireless card is a Broadcom Corporation BCM43142 802.11b/g/n
I have been using Raspberry PI a little, so i am familiar with the terminal.
I'm trying to find a driver for my wireless card (Atheros AR928X) and I think it's ath9k what I need. As far as I know there isn't a linux driver for it, so I installed ndiswrapper to use a windows driver instead. The problem is that when I type modprobe ndiswrapper I get "bash: modprobe: command not found" (even as root). I know I'm missing something about modprobe, but I can't find any help on google. Anyway, I installed ndisgtk next, because I thought it would be easier, but when I go to System> Administration> Windows Wireless Drivers I get a message "Unknown error".Do you have any ideas on how I'll make ndiswrapper work?
View 3 Replies View RelatedI seem to be have issues periodically connecting to wireless networks with WPA. It'll work one minute, and then I switch my macbook back on after a period and it refuses to connect again. It's happened on and off on three different networks now.
An example of /var/log/syslog:
Code:
Apr 15 17:57:27 macbookpro NetworkManager: <info> Activation (eth1/wireless): association took too long.
Apr 15 17:57:27 macbookpro NetworkManager: <info> (eth1): device state change: 5 -> 6 (reason 0)
Apr 15 17:57:27 macbookpro NetworkManager: <info> Activation (eth1/wireless): asking for new secrets .....
Apr 15 17:58:27 macbookpro NetworkManager: <info> (eth1): deactivating device (reason: 0).
Apr 15 17:58:27 macbookpro NetworkManager: <info> Policy set 'Auto eth0' (eth0) as default for routing and DNS.
Apr 15 17:58:29 macbookpro wpa_supplicant[949]: WPA: No SSID info found (msg 1 of 4).
Apr 15 17:58:29 macbookpro wpa_supplicant[949]: No network configuration found for the current AP
Apr 15 17:58:29 macbookpro wpa_supplicant[949]: CTRL-EVENT-DISCONNECTED - Disconnect event - remove keys
I just installed fresh Squeeze to my new hpmini 210-1100 netbook. No wireless. I have checked and I have Network Manager installed already.
I also compiled and installed Broadcom driver from here[url]
I followed their instructions and compiled the driver. I did get a wl.ko driver and installed it insmod wl.ko after modprobe lib80211
I noticed after rebooting neither wl.ko nor lib80211 showed when i did lsmod. So I did modprobe and insmod again. Still no wireless. Here are output of some commands that I thought would be relevant.
lspci:
I see only 2 computer icon in the system tray but not the parallel bars. When I went to System>Administration>Network, I was not able to add my wireless network name. The Add button was grayed out.
I'm thinking of installing Fedora 14 on my hp laptop, and need to know if this will support the Broadcom 4322AG wireless card it came with, will only probably use Fedora if the card is already recognized, or an easy gui install. This is the game changer between using fedora or linux mint for me
View 1 Replies View RelatedI finally gave up trying to configue the Broadcom 4311 card. I went and bought a Netgear WPN111 USB wireless adapter. I've looke for the drivers but I can't seem to find them.
View 3 Replies View RelatedI have had trouble in nearly every linux distrobution cept for backtrack 3(heavily modified ubuntu which has a lot of wireless drivers on it. i know A LOT of people in the past have had trouble with these cards.
View 9 Replies View RelatedI have installed SATA driver recently...Even if i can use wifi but i could'nt find any ath0 interface in ifconfig or iwconfig commands....My wifi is taking place through eth1 interface why it happens.....The reason for asking this in order to use aircrack for wep key it says that the injection process only applicable for Athelon interfaces but mine is eth1...I was just trying aircrack-ng...
View 2 Replies View RelatedHow to use the BRCM driver for this following wireless cards?
BCM4313
BCM43224
BCM43225
Seems the since the 2.6.37 kernels it would be included. And wouldn't be necessary to use Broadcom STA linux driver anymore.
I'm about to install OpenSuse 11.3 gnome on my laptop with ubuntu & vista in a dualboot, and wanted to make sure that the Broadcom 4322AG wireless card would be compatible with my laptop.
View 2 Replies View Related