Networking :: Nmap Showing Wrong Information?

Oct 16, 2010

I'm not too sure if this is the right topic to post in but if it isn't please move it to the correct topic. I recently opened some ports for my Playstation 3 and the connection test on the PS3 tells me that the ports are open . But when I execute this command

nmap -p 0-60000 192.168.1.5 I get this

Quote:

Starting Nmap 5.21 ( http://nmap.org ) at 2010-10-16 20:54 AUS Eastern Daylight
Time Nmap scan report for PS3 (192.168.1.5)
Host is up (0.00063s latency).
All 60001 scanned ports on PS3 (192.168.1.5) are closed
MAC Address: **:**:**:**:**:** (Sony Computer Entertainment)

Nmap done: 1 IP address (1 host up) scanned in 4.12 seconds

I could be executing the wrong command or something but I have read through the manual and couldn't find anything that helped. I have tried this command on other machines that I have opened ports for and get similar results except for a few Ephemeral ports (80,443 etc.) which also makes me wonder why these aren't listed as open on the PS3?

View 2 Replies


ADVERTISEMENT

General :: Nmap (No Ports Showing Open)

Apr 16, 2011

I scanned my home machine (windows vista) with Nmap, after disabling the firewall and all ports came back with the status as unknown (No Open Ports). Why no ports are showing as open?

View 3 Replies View Related

Hardware :: Wrong RAM Memory Information At BIOS

Nov 4, 2010

I have 4GB RAM installed on my PC (ASUS P7H55M-BR, Intel i3 530 2,93Ghz). Onboard video has 32 MB (BIOS config).

It should be this way (or maybe not?):Each slot has 1GB of RAM memory: 4 x 1024 MB = 4096 MB.

Now, subtracting the video memory: 4096 MB - 32 MB = 4064 MB.

It's working on Dual Channel.

But when I am booting the system, the BIOS shows only 3920 MB (3,9GB). Linux shows even lower: 3881 MB.

Memory Remap Feature is enabled at the BIOS config.

View 5 Replies View Related

Hardware :: Xbindkeys Giving Wrong Mapping Information

Apr 7, 2010

I'm having a problem with xbindkeys giving the wrong mapping information, hence I can't get it work at all when trying new mappings from this machine. From another computer, I have some definitions for xbindkeys (made with xbindkeys-config). These key codes work correctly on this computer I'm having difficulty with. From the config file for example:

[Code]...

View 1 Replies View Related

Ubuntu :: Showing More Information From Lm-senors

Dec 25, 2010

I have followed the guide here on the forums, and still can't get much to show up when running "sensors" from within terminal.This is all that will show up when I run 'sensors' in terminal:This has me puzzled, as I followed the guide exactly as it was stated, and I can't get everything working. Is my hardware too new or something?

View 3 Replies View Related

Red Hat / Fedora :: Du Is Showing Wrong ?

Mar 24, 2009

I've got my data disk partition like this:

Filesystem Size Used Avail Use% Mounted on
/dev/sda5 256G 74G 169G 31% /data

When i run the command du -hs * on /data it tells me I used 538GB. How is that possible? Is it possible to get the right amount?

View 8 Replies View Related

Red Hat :: Multipath Information In Vxvm Showing As 8 Paths

Apr 9, 2010

I am working on a server which connected to two EMC storage box. when i am checking the multipath information of a disk its showing as 8 paths. how to understand 8 paths for a single disk.

[Code]....

View 1 Replies View Related

Ubuntu :: Showing Wrong Disk Usage

Oct 29, 2010

I have benn using ubuntu on an old laptop to run a samba server and a torrent server and it has been working fine till a few days ago when it stopped letting me write any files to the disk, So i tried deleting some of the files i no longer needed to free up some space and the disk usage didnt decrease so i checked it out using the disk usage analyzer and it says its full but i know for sure its not.

View 9 Replies View Related

Server :: Rsync Showing Wrong Output?

Feb 16, 2011

Iam comparing 2 filesystem using the below command.rsync -navrz --exclude=logs/* /opt/otm/ glrrd@105.78.7.100:/opt/otm/The output showing the files which are same in size and timestamp that are to be sync.Iam using rsync 2.6.3 version so i dont have itemize changes option to debug the problem.Is there anyway i can find the how rsync is finding the difference between the 2 filesytemEx: filesystem1

-rw-rw-r-- 1 glog glog 39132 Nov 26 2009 FinJ-code_2003-10-22_12h17_CEST+0200.jar
-rw-rw-r-- 1 glog glog 39132 Nov 26 2009 finj.jar
-rw-rw-r-- 1 glog glog 954987 Nov 26 2009 jakarta-taglibs-standard-1.1.2.zip

[code]....

View 3 Replies View Related

Server :: Phpinfo Stops On Showing Date Module Information?

Feb 7, 2011

I have an apache2 php5 on an ubuntu 10.04 it was working fine except today and does not open web site now. I tried to open phpinfo.php but it takes long time and at the end it loads php informations just until date module. I installed php5-cli to find out what does not work properly then I used:

Quote:

# php5 -i
PHP Deprecated: Comments starting with '#' are deprecated in /etc/php5/cli/conf.d/mcrypt.ini on line 1 in Unknown on line 0
PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib/php5/20090626+lfs/gd.so' - /usr/lib/php5/20090626+lfs/gd.so: cannot open shared object file: No such file or directory in Unknown on line 0
PHP Warning: PHP Startup: Unable to load dynamic library '/usr/lib

[Code]....

View 6 Replies View Related

Ubuntu :: Login Screen Showing Up On Wrong Monitor?

Mar 28, 2011

one of them is a TV with an HDMI input. The login screen shows up on the tv, so if someone is watching a movie, I have to pause it to switch inputs and login. Other than that, everything is fine. How do I get the login screen to show up on the main monitor?

View 1 Replies View Related

Ubuntu :: Desktop Showing Wrong Folder Contents

Jul 22, 2011

My ~/Desktop is generally kept empty.

Yesterday on start resume from hibernate, it looked as if my encrypted home directory was unmounted; or at least instead of my $HOME contents I got a bunch of files related to this.

I rebooted the system, and since then my desktop has been rendering icons for every file in my home directory, but not updating the icons until the next reboot, if I change anything in $HOME while it is running.

I opened the gconf-editor and checked: the box for using the home dir as the desktop is not checked. I even tried toggling it and the option that controls drawing the desktop on/off in every possible combination. Nadda. The only thing that works is turning off drawing the desktop.

View 3 Replies View Related

Networking :: Using NMAP On A Range Of IP Addresses

Dec 21, 2010

Hopefully Ody has found a result in the 5 years since he posted this question, for anyone else looking for an answer
NMAP scan for a range of individual IP's can be done using the '-' for example:
(this is accurate as of 2010, actual results have been altered to match OP's address range)


$nmap -sP 192.168.0.1-14

Starting Nmap 5.00 ( http://nmap.org ) at 2010-12-22 09:55
Interesting ports on 192.168.0.1:
Not shown: 999 closed ports
PORT STATE SERVICE
80/tcp open http


Interesting ports on 192.168.0.2
Not shown: 999 closed ports
PORT STATE SERVICE
80/tcp open http


Interesting ports on 192.168.0.3:
Not shown: 999 closed ports
PORT STATE SERVICE
80/tcp open http

Nmap done: 14 IP addresses (3 hosts up) scanned in 8.08 seconds

View 1 Replies View Related

Fedora :: Hard Drive Showing Wrong Free Space?

May 15, 2011

[URl]also I wonder why there is such a gap between the size of the files (7 GB) and their size on the disc (44 GB)

View 13 Replies View Related

Ubuntu Servers :: Landscape Showing Wrong Temperature On HP Proliants?

Dec 9, 2010

Here is quick fix I did for HP Proliant servers where landscape shows wrong temperature eg:

root ~ # landscape-sysinfo
System load: 0.12 Temperature: 8 C <----- WTF
Usage of /: 0.2% of 808.13GB Processes: 214

[code]....

View 1 Replies View Related

Networking :: Can Nmap Detect Port-sharing

Sep 28, 2010

Since I no longer have access to a spare machine to actually test this out on, I was hoping some kind soul might know the answer, or be willing to try it out for me. I'm trying to find out if the port scanner nmap can detect two different services which are sharing a single port. For instance, if I'd managed to set up, I dunno, a web server and an ftp server to both run over the same port, would nmap with version detection be able to detect both of them, or just one?

View 7 Replies View Related

Debian Hardware :: Fibre-Channel RAID Not Showing, Wrong Setup?

Jun 8, 2011

I've been running Debian for a while, and now have the chance to do some enterprise-level experimentation. I stumbled across a very cheap EMC Clariion CX300 fibre RAID unit on eBay with 10 disks (90!), so I snapped it up with a fibre HBA. It's not a SAN, technically a DAS in its current configuration. I'd like to know how hard it is to set up one of these as an actual disk device in Debian.I tried installing the HBA (an Agilent Tachyon XL2 PCI-X card, 32 and 64-bit modes) in my current 'live' server (a Celeron 1.2GHz-based machine), but while Debian detected it as a FC controller card, mapping the LUNs within Navisphere on the CX to the host caused nothing (obvious) to show up in the OS. From what I've read about setting up SANs (not DASs, there seems to be precious little info on setting up these), there's firmware involved with the card, and there are no references to getting a Tachyon running under Linux.

I also snagged a good deal on a PowerEdge 1850 server, but as it's the PCI-Express version, the Tachyon won't fit, so I'm considering buying a PCI-E HBA. I found a QLogic QLE2460 for a good price, but I'm hesitant to buy it, in case I still can't get Debian to see the disks. I'd most like to have the device connected to the PowerEdge instead of the Celeron machine. Have I missed a step in the configuration, or is there anything I can do to test if the system is working as it should be? The units we use at work are much simpler: set the RAIDs up, map the host LUNs and the disk shows up in Windows. I'm also sure I've set everything up correctly on the CX, as the same LUN is available to Windows. Just need to get Debian to see something on the end of the HBA!System Specs:Live Server: Celeron 1.2GHz, 512MB RAM, Intel D815EEA2 board, SATA soft-RAID hard drives, PCI Gb Ethernet and USB2.0, Agilent Tachyon XL2 PCI-X FC HBA, Debian 6.0.1PowerEdge 1850: 2x 3.2GHz Xeons, 6GB RAM, SCSI RAID disks, PCI-E riser, planned QLogic QLE2460 PCI-E HBARAID Unit: EMC Clariion CX300, 10x 146GB FC disks, 2Gbps Fibre-channel interfaceThe PowerEdge is the planned replacement for the Celeron machine, which started life as my experimentation box and became my personal live server. Storage is holding it back, so I'd love to add a further five disks to the CX and have nearly 2TB of RAID-protected storage.

View 1 Replies View Related

Ubuntu Networking :: Nmap Ping A Pc With Icmp Disabled?

Nov 13, 2010

I tried to ping some of the pcs on the local network but for those with icmp disabled it doesn't work. I've used

Code:
nmap -sP 192.168.2.0/24

View 3 Replies View Related

Ubuntu Multimedia :: Creative Zen Vision:M Showing Wrong Partition Size (After Format)?

Apr 11, 2010

I have a issue in that my 30gb creative zen is showing up fine as a media device, I can delete and add files. It is showing up as z 3.9gp partition. I formatted inside the Zen I formatted inside Windows Vista It showed 28,800ish megs free and it still showed up at a 3.9 gig partition There is no .trash folder How can I fix this? Qlix installed don't know if that matters.

View 1 Replies View Related

Ubuntu Networking :: QBittorent With Portforwarding 6881 - Router And Run Nmap On Localhost "no Direct Connections"

Mar 16, 2011

is there still a bug in qBittorent with portforwarding 6881? i forwarded it in my router and run nmap on localhost and shows its open yet it is always saying no direct connections on the bottom with that little yellow globe near the nodes

[Code]....

View 1 Replies View Related

Fedora :: Write A Program Which Would Get Information From A Webpage And Display The Information On Desktop Sort Of Like A Widget?

Sep 3, 2009

I'm trying to write a program which would get information from a webpage and display the information on my desktop sort of like a widget. I kind of remember there being something like this already made, but for the life of me I can't remember what it's calledDoes anyone know?

View 1 Replies View Related

OpenSUSE :: How To Install Nmap?

Feb 20, 2011

So I tried to install it using the install/remove software and then run it out of the start menu but nothing happens. Bear with me I am new to linux,

View 9 Replies View Related

Ubuntu Security :: HOW TO Installing NMap 5.20 In X64

Jan 22, 2010

If you have been trying to compile & install the new NMAP 5.20 scanning utility as a 64 bit user, you may have run into some issues as I did...The compiler will halt when you attempt to 'make', saying that you need to recompile using -fPIC.The fix: "./configure CXXFLAGS=-fPIC CFLAGS=-fPIC LPFLAGS=-fPIC"then rerun "make".I hope this helps someone, as it took me way longer than it should have to get this going. Enjoy the new versions as it is supposed to have 10,000 updated OS detection signatures and new scripts!

View 2 Replies View Related

General :: How To Upgrade Nmap On Backtrack

Mar 29, 2011

i have old version for nmap:root@bt:~# nmap --version nmap version 5.35DC1 ( http://nmap.org ) i download new version, but before i install it, is there a way to upgrade the old one on my system? or need to un-install the old version and install the new version? i tried this:

root@bt:~# yum upgrade nmap
Setting up Upgrade Process
Could not find update match for nmap
No Packages marked for Update
root@bt:~#

View 8 Replies View Related

General :: Using Awk To Clean Up Nmap Output?

Jan 13, 2011

Wondering how to use awk to take nmap's output "Discovered open port 23/tcp on 192.168.0.4" and create a output of "192.168.0.4:23"?

View 9 Replies View Related

Security :: Detect Nmap With Iptables?

Apr 27, 2011

i have a problem with iptables when i use nmap to scan ports then ports shown.this is my rules on my firewall.Quote:

*filter
:INPUT ACCEPT [0:0]
:FORWARD ACCEPT [0:0]
:OUTPUT ACCEPT [1002:40080]
:RH-Firewall-1-INPUT - [0:0]
-A INPUT -j RH-Firewall-1-INPUT

[Code]...

View 3 Replies View Related

Debian Configuration :: Nmap Never Updates Scriptdb

Aug 25, 2015

nmap does not update the scripts when launching Code: Select allnmap --script-updatedb from ANY debian i EVER tried.

I cannot find a workaround, just old bug reports that this is fixed.

Why, is this not ever working on debian. I expected an update-nmap-db command to be Debian conform but there is no such thing.

Running Wheezy with latest updates.

View 0 Replies View Related

Debian Configuration :: Different Nmap Results And Configure A MTA?

Jan 26, 2010

I have been trying to configure an MTA (sendmail) on a new Debian installation to receive system messages and local network mail. I have no need to fetch or relay mail outside my teeny LAN. The logs on the sending machine told me the mails were refused by the receiving (Debian Lenny) system. So I ran some quick nmap scans. From the sending machine, scanning the Debian machine:

PORT STATE SERVICE
22/tcp open ssh
111/tcp open rpcbind

From the Debian machine, running 'nmap localhost':

PORT STATE SERVICE
22/tcp open ssh
25/tcp open smtp
111/tcp open rpcbind
587/tcp open submission

From the Debian machine, running 'nmap debian' (this is a virtual machine named debian) :

PORT STATE SERVICE
22/tcp open ssh
111/tcp open rpcbind

Why the two different results? How do I get the scans to be the same so I can, eventually, configure an MTA?

View 3 Replies View Related

General :: Scanning A LAN For Specifc Ports With Nmap?

Jul 16, 2011

I want to identify all the computers on my LAN that have port 80 open. So I want to scan an IP range (192.168.0-255.0-255) and have Nmap print onto the screen all the IPaddresses it scanned that are accepting connections on port 80. How do I do this?

View 1 Replies View Related

Security :: Show Banners On Nmap For Apache2?

May 5, 2011

when I nmap -sV domain I can see my chrooted apache2 banner how can I do not even show the banner even if is chrooted.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved