Networking :: Multiple IPV4 Addresses Not Working After Boot

Oct 15, 2010

Fedora 12 running under VirtualBox 3.2.8 w/ Bridged networking
Host OS Windows 7

I have 3 IP addresses set up in on my Fedora 12 installation:
Directory: /etc/sysconfig/network-scripts/
ifcfg-eth0 -> 192.168.0.170
ifcfg-eth0:0 -> 192.168.0.171
ifcfg-eth0:1 -> 192.168.0.172

Hostname is configured to host associated with 192.168.0.170 in /etc/hosts

When I reboot and execute
# ifconfig

eth0 is associated with the 172 address and the other addresses are not active. After I run
# service network restart

All of the addresses are active and associated with the correct interfaces. Content of my ifcfg files below:

/etc/sysconfig/network-scripts/ifcfg-eth0 :
Code:
# Intel Corporation 82540EM Gigabit Ethernet Controller
DEVICE=eth0
HWADDR=08:00:27:0A:9D:24
ONBOOT=yes
TYPE=Ethernet
BOOTPROTO=none
IPADDR=192.168.0.170
PREFIX=24
DNS1=192.168.0.1
NAME="System eth0"
UUID=5fb06bd0-0bb0-7ffb-45f1-d6edd65f3e03
GATEWAY=192.168.0.1
IPV6INIT=no
USERCTL=no
NM_CONTROLLED=yes
/etc/sysconfig/network-scripts/ifcfg-eth0:0 :

Code:
# Intel Corporation 82540EM Gigabit Ethernet Controller
DEVICE=eth0:0
TYPE=Ethernet
BOOTPROTO=none
IPADDR=192.168.0.171
PREFIX=24
DNS1=192.168.0.1
NAME="System eth0"
UUID=5fb06bd0-0bb0-7ffb-45f1-d6edd65f3e03
GATEWAY=192.168.0.1
IPV6INIT=no
USERCTL=no
ONPARENT=yes
NM_CONTROLLED=yes
ONBOOT=yes
/etc/sysconfig/network-scripts/ifcfg-eth0:1 :

Code:
# Intel Corporation 82540EM Gigabit Ethernet Controller
DEVICE=eth0:1
TYPE=Ethernet
BOOTPROTO=none
IPADDR=192.168.0.172
PREFIX=24
DNS1=192.168.0.1
NAME="System eth0:1"
UUID=5fb06bd0-0bb0-7ffb-45f1-d6edd65f3e03
GATEWAY=192.168.0.1
IPV6INIT=no
USERCTL=no
ONPARENT=yes
NM_CONTROLLED=yes
ONBOOT=yes
After booting:

Code:
# ifconfig

eth0 ....

Restart network:
Code:
# service network restart
. . .
# ifconfig

eth0 ....

eth0:0 ....

eth0:1 ....

View 3 Replies


ADVERTISEMENT

OpenSUSE Network :: Assign IPv4 And IPV6 Static Addresses?

Feb 19, 2010

How do I assign IPv4 and IPv6 static addresses permanently in OpenSUSE 11.2? Currently I am only able to assign either IPv4 or IPv6 static address not both. I cannot find even the interfaces file(/etc/sysconfig/network/interfaces).

View 2 Replies View Related

Networking :: NAT With Multiple Internet Addresses

Mar 8, 2010

My Linux gateway has multiple address to internet:
eth0 = 76.148.200.3
eth0:0 = 76.148.200.4
eth0:1 = 76.148.200.5
and it's own gateway which is 76.148.200.2 (probably not relevant) and I also have which is not internet, but local:
eth0:2 = 192.168.0.1 netmask 255.255.255.0

They all work fine and tested. Now I am sharing the internet through eth0 (76.148.200.3) to 192.168.0.1/24 and that's working fine. The script I use to do that is here...

Code:
#!/bin/sh
echo 1 >/proc/sys/net/ipv4/ip_forward
echo 1 >/proc/sys/net/ipv4/ip_dynaddr
iptables -t nat --flush
iptables -A FORWARD -i eth0 -d 192.168.0.1/24 -m state --state ESTABLISHED,RELATED -j ACCEPT
iptables -A FORWARD -s 192.168.0.1/24 -o eth0 -j ACCEPT
iptables -A FORWARD -j LOG
iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE

Now all I want to change in the script is to share it through 76.148.200.4 (eth0:1) instead of what is already sharing through 76.148.200.3 (eth0). I am sure this is easy but can't work it out and iptables doesn't accept 'aliases'. How I can do this by modifying this script?

View 5 Replies View Related

Ubuntu Networking :: Upstart Vs. Multiple IP Addresses ?

Jan 27, 2010

I have run into a problem that I've tracked down to being a conflict between the "Upstart" init system, and how it handles multiple (alias) IP addresses per physical interface. The summary of the problem is that the interfaces are being configured in the background in parallel with the starting of daemons. One "feature" of this (apparently intended for pluggable devices that would add or remove an interface) is that the network daemons are restarted each time an interface is added (and presumably deleted). But this is a disaster when applied to alias IP addresses.

I first saw the effects of this when during booting Ubuntu Server, the screen showed a message about OpenSSH daemon being restarted ... several times a few seconds apart each. At the time I didn't know what was causing that, but didn't worry because it ultimately was running when I needed it.

But now that I am deploying these servers for specific duty with many IP addresses per system (per network interface), the symptoms are becoming serious, and I need a solution.

1. The IP addresses are coming online too slowly. Apparently the time it takes to restart each daemon is being added to each address being configured.

2. It appears to be disrupting some daemons sometimes. Occaisionally, some daemon just ends up being hung somewhere, or dies. Too many restarts.

3. Sometimes few or even no alias addresses get configured. This might be due to a daemon getting hung, and the whole sequence just not finishing.

4. The "nsd" name server as packaged by Ubuntu doesn't deal well with this at all. It needs all its IP addresses to be up when it starts, or else it won't start. The Ubuntu package of it doesn't including any if-up script at all, although I'm not sure that would do any good.

What I need is a way to configure all these alias IP addresses so they are all configured immediately when the point in time is reached to bring up network interfaces for the first time. These are all static, and all are aliases on ethernet NIC cards plugged into PCIe cards, or integrated in the mainboard. None of them are pluggables. I did run a manual test of "ifconfig" in a loop configuring 2540 alias IP address on eth0 and it only took 2 seconds (no if-up triggers or daemon restarts here). So I know it's fast if nothing else is done between these steps.

Even for pluggable physical interfaces, I see no reason to even try to step through every alias (if it has aliases) with a daemon restart. If an alias IP address is added on later, then I can understand doing it. But if you have a list of 100 aliases for a physical interface, they really should all be done ... or at least attempted ... at once, and do any triggers needed after that.

So, how can I configure or modify Ubuntu Server 9.10 to do that?

I have each alias listed in the "/etc/network/interfaces" file with a separate "auto" and "iface" section for each one, with sequential sub-interface numbers appended to the interface name. I tried it without those sections (e.g. just "address" and other items in sequence) and that prevents the system from even coming up (bootable CD to the rescue to undo that). At least cntrl-alt-del did reboot it.

I tried to attach the /etc/network/interfaces file, but I don't know if it worked because I see no confirmations about it. if it didn't attach and you need to see it, say so, and I'll just paste it in a followup.

View 2 Replies View Related

Ubuntu Networking :: Getting Dynamic Ip Addresses For Multiple Interfaces?

May 6, 2010

I have 4 Ethernet Interfaces. I need Dynamic IP-Addresses for 2 Interfaces. Can anybody help me how can i achieve that

View 3 Replies View Related

Networking :: DHCP Script - Assigning Multiple IP Addresses By Mac?

Sep 6, 2010

Ive been trying to give certain clients an IP adres by mac adress. For this I use the folowing code:

host apex {
hardware ethernet 00:00:00:00:00:00;
fixed-address 192.168.250.100;
}

This works perfectly, however when I try to add a second client this way it doesnt. I tried to add the above code multiple times as a whole (2 times the above code) but that doesnt work. I also tried to just add more lines under host apex but this also doesnt work.

So my question is: How do I add more of this mac related IP adress assignments in the dhcp.conf?

View 1 Replies View Related

Networking :: Forward Multiple Public Addresses With Iptables?

Jun 3, 2011

iptables and multiple public-facing IP addresses. With the current setup I have a public-facing firewall with iptables which will then forward traffic to a LAN IP. I will hopefully be allotted 1 private IP per public IP, which I hope will make this much more simple. For example, I have server A with the LAN IP of 10.0.0.1 which I would like to have traffic forwarded from 5.0.0.1, the public IP. I also have server B with LAN IP of 10.0.0.2 which I would like to have forwarded from 5.0.0.2, the second public IP. From what I have read and understood, this should be a simple task, however I would just like to double check to make sure that it is in fact possible, and if so, how would it be recommended that I go about doing so. Essentially, I need to forward each public IP to a corresponding LAN IP with all ports.

View 3 Replies View Related

CentOS 5 Networking :: Multiple Static ISP IP Addresses / Servers Configuration

Mar 31, 2011

I have a CentOS5 server with dual ethernet adapters + Webmin installed as my Router / Firewall / DHCP server working successfully with 1 static IP from my ISP. I also have 7 additional static IP addresses from my ISP needing to configure to individual servers inside my network. I have configured the additional virtual interfaces, but am lost on how to route data specifically from additional ISP address to specific internal network address.

Below is my desired configuration.
98.173.159.xx1 = eth0 physical interface ==> eth1 192.168.1.1
98.173.159.xx2 = eth0:1 virtual interface ==> 192.168.1.10 ==> CentOS Server 2
98.173.159.xx3 = eth0:2 virtual interface ==> 192.168.1.20 ==> CentOS Server 3
98.173.159.xx4 = eth0:3 virtual interface ==> 192.168.1.30 ==> CentOS Server 4
98.173.159.xx5 = eth0:4 virtual interface ==> 192.168.1.40 ==> Mac OS X Server 1
98.173.159.xx6 = eth0:5 virtual interface ==> 192.168.1.50 ==> Mac OS X Server 1
98.173.159.xx7 = eth0:6 virtual interface ==> 192.168.1.60 ==> Network Attached Storage Server 1
98.173.159.xx8 = eth0:7 virtual interface ==> 192.168.1.70 ==> Windows 2008 Server 1

View 2 Replies View Related

Ubuntu Networking :: Multiple External IP Addresses With Single Physical Ethernet Card And Virtualization

Feb 16, 2010

I recently installed Ubuntu Server 9.10 with the intent of using it as a platform for running a couple of Windows XP virtual machines along with Linux/Ubuntu.

I had no problems getting the server installed. Had no problems getting the network up and running so that I had access to both my internal network as well as external connectivity to the internet. Had no problems getting a VM installed and putting Windows XP inside of it. Had no problems setting up a bridge between the WinXP virtual machine and the physical ethernet card (eth0).

What Im having trouble with is figuring out how to bridge from multiple VMs AND Ubuntu natively through one physical ethernet card.

When I set up the bridge, it knocks out the static IP address of the ethernet card that was set up initially with Ubuntu when first installed before the VM was created and installed. Therefore, connectivity within Ubuntu natively is lost.

Similarly, am having trouble figuring out how the second VM (also going to be running WinXP) is going to get its connectivity since it doesnt seem to like me setting up 2 bridges to the same physical ethernet interface card.

I need all 3 machines to have static IP addresses and be visible/accessible from the external network for either web/mail/dns/etc servers on the Ubuntu side and for remote PC control functionality on the VM side.

I have tried setting up alias ethernet interfaces (eth0:1, eth0:2, eth0:3) with static addresses which work fine from native Ubuntu in presenting multiple IP addressees, but it seems that Im not permitted to bridge to these alias interfaces.

View 5 Replies View Related

Red Hat :: Disabling IPv4 Packet Forwarding: Net.ipv4.ip_forward = 0 (CentOS 5.5)?

Oct 29, 2010

I'm forging a gateway server, We have 2 Internet connection that goes to a load balancer router, and goes to my centos server and from our server goes to a switch for Internet distribution or routing.

OS-CentOS 5.5
[root@server etc]# uname -srio
Linux 2.6.18-194.el5 i386 GNU/Linux

My eth0 and eth1 has the following configuration and IP

[root@server etc]# cat /etc/sysconfig/network-scripts/ifcfg-eth0
# VIA Technologies, Inc. VT6105/VT6106S [Rhine-III]
DEVICE=eth0
BOOTPROTO=none

[code]....

Disabling IPv4 packet forwarding but i already changed it to 1 at sysctl.conf One of the online forum says i need to configure the named.conf deleted some and run it(named.conf) and successful but still when I run network service I still get the :"Disabling IPv4 packet forwarding: net.ipv4.ip_forward = 0" The network is getting the IP range but it doesnt get any Internet connection.

View 3 Replies View Related

Networking :: DNS Reverse Lookups Not Working For Private IP Addresses / Fix It?

Jul 13, 2011

We have bind 9.3 running on CentOS 5.2. We are able to do reverse lookups for the public IP's but not able to resolve to the private IP's on our network.

View 1 Replies View Related

Debian Configuration :: KVM / One Interface / Multiple IP Addresses

Dec 27, 2015

I'm renting a server which comes with 5 IP addresses, but only one network device. From what I can understand I'm able to create aliases by adding entries to /etc/networks/interfaces, I haven't tried I'm in the planning stages. Hypothetically, 192.168.22.30 is my primary IP and I want to set eth0:1 to have 192.168.22.31, and then after that I want to create a virtual machine (using kvm/qemu) that is able to communicate bidirectionally to the internet over eth0:1, and leave eth0 strictly for administrating (not for VM traffic).

The qemu guides I'm finding seem to assume that I want to use TAP or VDE, what I want to use is a sub-ip/alias. One guide I saw had me eliminate everything from eth0 and put it under br0. That would leave me unable to ssh into my server (and unable to administrate). Is there a way I can do something along the lines of: qemu [options] -net [option] -netdev=eth0:1 ?

View 1 Replies View Related

OpenSUSE Network :: Set Multiple IP Addresses Onto Server?

Jul 23, 2011

I want to set multiple IP addresses onto my server and I can then put under an alias.

But is it possible to somehow create a script in perl example that can do this for or is it only possible manually?

View 1 Replies View Related

Server :: Setting Up Postfix To Use Multiple IP Addresses?

Apr 17, 2011

I set-up his mail server for him with Postfix but what he wants I have no idea how to do.

Essentially he wants it so that the mail gateway IP corresponds with the dedicated IP of the domain and I have no idea how to accomplish this.

I found some documentation on the web saying that the fix for this was to run multiple instances of Postfix which I tried doing but each time I try to start the second instance I get the error that postfix is already running.

There has to be an elegant way to make this happen, I really hate to tell a client something can't be done even though the concept is a bit pointless, IMHO. I am hoping I can get some feedback here on if this can be done and if it can the easiest way for me to accomplish doing it.

Here is some of the config files (example.com has been put in place of the actual domain names and the ip of 5.5.5.5 is in place of the actual IPs


Code:
[root@youronlinehosting ~]# cat /etc/postfix/transport
example.com smtp:5.5.5.5
example.com smtp:5.5.5.6
example.com smtp:5.5.5.7

[Code].....

View 1 Replies View Related

General :: Ubuntu - Increasing Download Speed By Using Multiple IP Addresses ?

Jul 4, 2010

Quite often sites limit download speed per ip address or identified user.

Is it possible to use a tool such as wget in order to overcome this limitation?

View 4 Replies View Related

Server :: Sendmail To Split Single Envelope Into Multiple To - Addresses

Aug 4, 2010

Our system uses email to send fairly time-sensitive status messages between programs running on various servers on a WAN. Each email message is sent to two addresses (different servers). The problem occurs when one of the destination mail servers is off the network. I think because it's trying to send one email to two addresses, sendmail attempts delivery to the first address, then to the second address (i.e., serially). When this happens, it hangs for two connect timeout (CONNECT_TO) periods trying to connect to the offline destination, then after the timeout, it then delivers to the other destination. I'm trying to figure out how to work around that connection delay so it doesn't delay delivery to the other destination.

I'm working with the network guys to enable the right ICMP messages that signal when a network is unavailable, but I would also like to try having sendmail split the emails into two envelopes, then use parallel, independent connections for delivery.

After days of reading through the docs (O'Rielly Sendmail book + sendmail docs) I think one way to do this is to use multiple mail queues, but I can't decipher exactly how to do that from the docs.

There might be other, more elegant ways to do the same thing, but again, trying to decipher the docs has my head swimming. (This is my first experience with sendmail.)

View 1 Replies View Related

Ubuntu Servers :: Setup An Outbound SMTP Mail Server With & Using Multiple IP Addresses

Mar 15, 2010

This is the current setup that we have: We have approx 20 clients who pay us to send out a type of e-mail called an E-Blast to their customers. We currently are using 5 Microsoft Windows Virtual Servers to do this. The problem is that those machines are starting to break down. There are times that it will take Microsoft Windows approx 9-10 hours to complete 1 job. This is way too long. We want to move away from Microsoft Windows for this particular type of job as it seems there are more customers who are wanting to use this type of advertising.

It seems that using a Linux Server "Command Line or Shell" environment would be the best way to go as there is no GUI like Windows. Since there is just text...that is something that would/should process very, very quickly.

I am in the process of setting up a new SMTP outbound mail server. This is the current software & configuration (what is installed on this new machine):

All of the customer data (Names, E-Mail Addresses, etc that these e-mails are going to) are currently loaded in a Microsoft SQL Database.

My machine that I am using is plugged into the DMZ. I have 1 ip address for the 1 network card. I have also added/bound 4 more ip addresses to that network card.

I have configured Postfix for Multiple IP Addresses.

I can, from the command line, send successful test e-mails and receive them in my personal account.

As far as I know everything is setup correctly. I can and will post requested information so that it can be verified that everything is setup correctly.

Here are a couple of my questions:

Ensure that I have my Network / Interfaces file and my Postfix's Master.cf/Main.cf files setup correctly?

How can I setup this server to be an Outbound SMTP server and get it to use all 5 of the IP Addresses to send these e-mails quickly?

What can I use to check and ensure that this server is in fact sending out emails on all 5 IP

Addresses (I heard that there is a program named "Postal" that may help in determing this).

View 3 Replies View Related

Ubuntu Networking :: 7.10 - No IPv4 With Eth0 - Can't Connect To LAN

Apr 19, 2010

Current problem: fresh, clean install of Ubuntu 7.10 on known good hardware does not use/produce/get/have an IPv4 associated with eth0, so cannot connect to my home network for Internet access.

Background: Have been wanting to build and maintain a home file server for some time now. Have also been wanting some hands-on practice to help me progress from Noob to Intermediate, eventually advanced Linux Tech. (I have two decades of tech support experience, but only small fraction of that using command lines and almost zero Linux.)

Anyway, every time I download and attempt to burn a recent distro on my Vista Shuttle, I only end up making drink coasters and mini-frisbees. so I thought that I might have better luck if I used a Linux Workstation to download and burn a server distro.

That's where I an now. I took one of my fully functional WinXP systems offline, replaced the WXP HDD with an old 3.2 GB, dug out my 2008 edition Linux Bible, popped in the DVD that came with it, and installed Ubuntu 7.10.

Everything else seems to have progressed smoothly, but I cannot seem to get the onboard Via chipset ethernet controller to talk to the router. When I run "ifconfig" in Terminal, I see IPv6 info, but nothing for IPv4.

When I try to configure eth0, it doesn't matter whether I set it up for DHCP or static... nothing works.

Is there a command line tht I can use in Terminal to manually configure eth0 to use IPv4?

View 3 Replies View Related

Ubuntu Networking :: Configuring IPv4 With Fixed Ip?

Aug 2, 2010

Our router is pretty old and only capable of giving fixed ip and there is no support for IPv6. Via the gnome networkmanager I try to set a manual IP to 192.168.1.123 and a netmask to 255.255.255.0 and a default gw at 192.168.1.1 . However, this does not work.

If I open a terminal and type:

Code:
sudo ifconfig eth0 inet 192.168.1.123
sudo route add default gw 192.168.1.1
Then I get a perfectly valid connection to the internet.
ifconfig by it self returns:

[Code]....

ffor me it seems that the gnome network manager doesn't save the information that I gently ask it to.

I can fix it with the CLI commands, but I would like to know whats going on.

View 6 Replies View Related

Networking :: Duplicate Address Detection In Ipv4?

Sep 22, 2009

Linux has duplicate address detection mechanism for IPv6 and nothing for IPv4 in kernel. At boot time, initscripts take care to check for the duplicate address but when an IP address is assigned using ifconfig or ip utility, no error is generated.

View 2 Replies View Related

Networking :: No IPv4 On Eth0 - No Connect To Router

Apr 20, 2010

I have tried clean installs of Knoppix v0.6, Xandros 2.0, and Ubuntu 7.1... same issue with all. I cannot seem to get eth0 (via chip on mobo) to get/have/use IPv4. ifconfig shows only IPv6. (I cannot paste any info because linux desktop is on different box.)

End result is that I cannot get the linux desktop to connect to my lan, either with dhcp or with static ip.

I have a belkin router configured as my gateway 192.168.3.1 and nothing fancy with the setup. I have dhcp open for 192.168.3.245 thru ...254 and at most there are only 4 systems in home connecting with dhcp at any time. all other systems have static addresses.

I have two decades of desktop and lan support under my belt, but relatively small amount of command line experience and almost no history with linux (unless you count a dozen unsuccessful attempts to burn linux distro install discs on this Vista desktop).

Therein lies the start of my prob. I need to build and manage a fileserver for my home, but cannot seem to get a working installer cd or dvd to burn from anything I download.

So I said to myself, "Self," I said, "you're a tech. Build a workstaion, use the DVD that came with your Linux Bible (2008 Ed.) to install one of the linux distros on it, then download a recent, stable server distro and burn it using the linux workstation."

Unfortunately, if I cant get an ipv4 connection to my home network, I cant get out to the Internet to download any newer ISO files.

So what am I missing or doing wrong? How do I tell linux to stop trying to use IPv6 and let me use IPv4?

BTW, eth0 works just fine if I install Windows on that PC, so I know its not bad HW. Could it be a driver issue? Or do I need to use some Terminal command to turn off IPv6 and reconfigure eth0 for IPv4?

View 5 Replies View Related

Networking :: IPV4 Syntax - Any Host On Network?

Sep 2, 2009

Can someone explain me ipv4 notation like:
192.168.1.0/255.255.255.0
Does it mean "any host on 192.168.1.x" network?

View 1 Replies View Related

Ubuntu Networking :: Apache Binds To Ipv6 But Not To Ipv4?

Sep 1, 2011

On my 10.04 LTS Ubuntu Server installation, apache2 doesn't bind to ipv4. It does bind to ipv6. I didn't notice this at first, because from my home connection I could visit the webpages without trouble. I noticed it running netstats -ta:

Code:
tcp 0 0 localhost:10024 *:* LISTEN
tcp 0 0 localhost:10025 *:* LISTEN
tcp 0 0 localhost:mysql *:* LISTEN
tcp 0 0 localhost:spamd *:* LISTEN

[Code].....

View 2 Replies View Related

Networking :: Working With Multiple Network Connection?

Jul 29, 2011

I have a pc running Ubuntu 10.10 with 2 wired net card and 1 wireless card, all of them connected to a router through which connected to the internet. My question is when I launch a connection, such as ping or visit a website with browser, which one connection the system uses or both of them? Can I manually specify one connection to use? How to do it?

View 3 Replies View Related

Ubuntu Networking :: Open Ports - How To Explicitly Check IPV4

May 4, 2010

Normally I use 'netstat -an' to determine if a daemon is listening on a specific port. The excerpt of this command below doesn't list things like vnc (5900) on ipv4. It does however show it on ipv6. My issue is I want to know how to determine if it is indeed listening on ipv4 as would normally be seen with 0.0.0.0:5900. It would appear that all ipv4 ports are internally being redirected to ipv6. Of course this does simplify things, but it also leaves me unable to reliably determine the ipv4 listening status. How I can tell at a glance if a specific ipv4 port is being listened on? Is there a way to force netstat to list the ipv4 listens specifically?
Code:
art@eee1:/proc/sys/net/ipv6$ netstat -an
Active Internet connections (servers and established) .....

View 1 Replies View Related

Networking :: Enable Duel Ipv4 / Ipv6 Stack On System?

Mar 12, 2010

How do you I use duel stack i.e How do I use ipv6 packet inside ipv4 packet using fedora kernel 12 ?

View 1 Replies View Related

Fedora Networking :: DNS Not Working With Multiple Network Connections

Mar 5, 2010

I have a machine that I'm trying to setup as a reverse web proxy. It will have two NICs, eth0 will face the public network, and eth1 will face the "internal" network (connects to a switch that goes out to the other web servers that are statically assigned a private IP address).

When both interfaces are started, I can ping hosts on the 1.2.3.0 network and the 192.168.10.0 network without problem when doing so by IP, but if I try to run a ping or nslookup command with a DNS name, it does not work. I've tried commenting out my entries in /etc/resolv.conf and adding the DNS entries in the /etc/sysconfig/network-scripts/ifcfg-ethX files directly (DNS1=x.x.x.x and DNS2=x.x.x.x), but the results are the same.

View 2 Replies View Related

Ubuntu Networking :: Assigned IPV4 Settings Manually - No Internet Connectivity

Jun 20, 2011

I am new to UBUNTU. I installed the latest one alongside windows 7. I am having problem with the internet connectivity. I configured the static ip settings right I guess. Edited the Auto eth1 and assigned ipv4 settings manually and entered everything correctly.

Address 192.168.xx.xx
Netmask 255.255.255.0
Gateway 192.168.xx.xxx
DNS Server xxx.xxx.xx.x, xxx.xxx.xx.x

Do I have to put MAC Address as well? Which is addressed as 'Network address' in Windows where I put this MAC. I have on board Realtek RTL8101E Family PCI-E Fast Ethernet NIC (NDIS 6.20) Network adapter. Do I have to install the driver?

View 3 Replies View Related

OpenSUSE Network :: Port Redirection - Multiple IP Addresses - Or Run On Port 80

Apr 7, 2011

In SuSE firewall0. I do have a openSuse 11.4 and multiple IP addresses on eth0 interface

I run (trying to/have to) multiple TOMCAT servers.

I am trying to have each tomcat instance listen to on separate IP address for example:

What i am trying to do is to redirect

a) tomcat 1 -

a) tomcat 2 -

And so on.

I know that it has to be possible.

I do have just eth0/

Is is it possible. Do I have to create "vittual interfaces"? eth0:1, .......... and do redirection ?

"Server" has got just single interface - just 1 ethernet calbe goes to that server. I am planning to have 10-15 tomcat's on that server (I have to unfortunatley) and each has to run on port 80

Is it possible to "grant" permissions to normal users to run app on port 80 - that would solve me lots of problems if impossible to redirect.

I tried to setcap 'cap_net_bind_service=+ep' /path/to/tomcat ...... but no luck

View 7 Replies View Related

Ubuntu Networking :: Wireless Stops Working With Multiple Intel 5100 (vaio) On Wifi

Nov 24, 2010

I'm using a Vaio TT, which seems to use an Intel 5100 WiFi chipset, and a Linksys WRT54G2 (firmwares 1.0.1 and 1.0.4), ubuntus 10.10 and 10.04.

Wifi works fine out of the box. However if the other vaio tt in our office (running windows 7) comes online, my laptop stops being able to make new connections. It WILL stay connected to chat servers, and downloads SOMETIMES continue to work. However all new HTTP requests / ssh connections / rdp connections / pings fail. The laptop still appears to be "connected" to the wifi network.

This may also happen after an undetermined amount of time without the extra vaio. It is not solved by reconnecting or rebooting. Once the extra vaio leaves the building, everything works fine again. This problem does not happen at all if I boot into windows.

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved