Ive got a problem on my server ....installed Debian 5 , Webmin and than syscp settung up syscp ready ....
I try to ping "localhost" ansver ping: unknown host
I try to ping "localhost." there is a host with IP 127.0.0.1
I need it to change it in "localhost"
Is that the bind9 maybe?
Even ping google's ip address doesn't work. unknown host error using backtrack4 able to browse net with these settings.
My network settings:
What's the problem with these settings...
I am using ubuntu 9.10 and I still cannot figure out this thing. I work behind a proxy managed by my university. Now, I cannot ping the other users on my network although they can ping me. Not to mention, I also cannot ping [URL]... It says : ping: unknown host [URL]... But I can ping the proxy server.
View 4 Replies View RelatedI've encountered a problem after doing a fresh install with xubuntu 10.10 (2.6.35-23-generic).some sites are blocked like [url]....if I do dig [url]....- I receive the A, CNAME records and the IP address and everything.when ping[url].... - I receive 'unknown host'.when ping <theipaddress> - I receive responses
View 2 Replies View RelatedHost - Fedora 12 64bit
KVM
VM - Windows Server 2008 64 bit
bridge-utils
VM can ping host and Internet but host can't ping VM.
I set VM static IP 192.168.0.205.
It turns out dynamic IP - 192.168.0.55
On host:
I am using an virtual machine. where I need to ping from one machine to another. earlier I was able to ping. But after going to google.com once, I cannot ping back to this machine.
But if I gave ping -I eth1 <IP> then I can ping.
I cannot install any package, so tell me solution which includes not installing any package.
Host - Fedora 12 64bit
KVM
VM - Windows Server 2008 64 bit
bridge-utils
VM can ping host and Internet but host can't ping VM.
I set VM static IP 192.168.0.205.
It turns out dynamic IP - 192.168.0.55
On host:
$ ping -c3 192.168.0.55
fails
I have a debian server installed with a static ip. Now i am able to ping my ip, but when i try to configure a domain name with the nameserver as my ip, i am not able to ping the domain name
eg:
I have two machines on this network, one running Ubuntu and the other running Fedora.
When I'm using the Wireless network on the Ubuntu machine, I cannot ping the Fedora machine. Everything else works. I can browse the net fine.
If I switch over to the Wired Network then I can ping the other machine.
I don't understand why ping doesn't work only over the Wireless. I can ping the router so I'm guessing it's getting blocked by the router but I didn't block ICMP traffic.
I tried asking on IRC and they ran out of ideas too to find out where the problem is.
I'm pinging a certain website and what happens is that each time the ping process freezes for an unknown reason ca. 10-15 sec then it starts to ping. Note that only this particular domain causes this hanging and Ctrl-c seems to have no effect at all! The domain is niteco. So far I've tried several independent linux systems all with the same result however other non-linux systems ping normally.
View 2 Replies View RelatedI made an ip packet using raw sockets and used icmp header of echo request inside that ip packet.I have a wifi lan with 2 host(laptops) connected to it. when I send the packets to any of these host the reply me with echo reply as i see in wireshark. but when i change the source ip and mac to that of another host there is no echo reply packet in the network but only echo request packet is there. Can anybody tell me why is this happening. and am also using Promiscuous mode so non of the packet is discarding.
View 3 Replies View RelatedI have a server that I can ping, and I can connect remotely with ssh to it. But when I try to connect to apache (port 80) I get "no route to host". But I can connect to localhost It's not just my client system that is having this problem but also systems that are on the same subnet There is no firewall running on the server route on the server
[Code]...
I just installed my first EVER bind DNS server. I am running bind9 on Ubuntu 10.04. Everything seems to be working great except one thing: If I ping a host that I have set up in bind by its HOSTNAME the pings take 5-6 seconds to reply/print to the screen between each echo response. If I ping by the host's IP address, they echo back very quickly.
I have read that IPv6 can cause this, but I have disabled it in /etc/sysctl.conf and the problem still exists.
I know everyone says this can't be a DNS issue, but this never was an issue with dnsmasq (which i was using prior), and it doesn't make sense that the ping are ONLY slow when pinging by hostname and not IP.
Configs below:
Ping by hostname - there is a 5-6 second delay between each one of the responses:
Code:
Ping by IP - the responses come VERY quickly one after the other:
Code:
/etc/resolv.conf:
Code:
Code:
rev.0.168.192.in-addr.arpa:
Code:
So, I have an Virtual Machine running CentOS 5.4. It sits behind a hardware firewall which also does NAT'ing. I've set up plenty of these, so I know for sure the firewall and NAT rules are set up correctly. From the host, I can ping anything in my subnet and the gateway. But I can't ping anything else beyond the gateway. I can perform DNS queries and when I try to ping, it finds the appropriate IP address.But from the outside, I can ping the PUBLIC address (It's a 1 public to 1 private address NAT, not 1 public to multiple private). I've tried it with IPTABLES on and off, with no change.
View 11 Replies View RelatedI have Mandriva One 2009.0 (192.168.1.100) on one box and Mandriva Free 2010.0 (192.168.1.118) on the other. I can ping router (192.168.1.1) from both of these boxes but I can't ping one box to the other and the other way around. What's going on?.
Do I have to change some settings in router?. Or is it firewall issue on those two machines?. Both of these boxes are connected by cable. Symbol of the router: TL-WR340G.
I have a somewhat complicated network setup that I am testing on an internal network. I have the following route setup:
PC Client (192.168.2.100) --> Router (192.168.2.1) --> DSLAM (on our internal network) --> PPPOE Server (192.168.9.1) on Linux Ubuntu 8.04 on interface card eth2.
On the same Linux Ubuntu Machine on interface card eth1 (static IP 192.168.5.100), I have an Asterisk SIP server plugged into it. SIP Server = 192.168.5.101 (static) I need the PC client (192.168.2.100) to register via SIP soft phone to register on the SIP server (192.168.5.101). From the PC client I can ping as far as the eth1 interface (192.168.5.100)...but cannot ping the SIP Server (.101).
From the SIP server (192.156.5.101)...I can ping 192.168.5.100, I can ping 169.254.5.228 (Eth2:avahi), but not sure what that is. I cannot ping the pppoe default gateway (192.168.9.1), which I think you cannot anyway. No firewalls are running. My IPtables I cleaned out totally. I think it might be as simple as a route add, but I really have no clue. Tried building a virtual bridge using brctl LINUX betweeh eth1 and eth2, but that made things worse (could not ping anything after that)
Route table:
Destination Gateway Genmask Flags Metric Ref Use Iface
192.168.9.100 * 255.255.255.255 UH 0 0 0 ppp0
192.168.5.0 * 255.255.255.0 U 0 0 0 eth1
[code]...
If I try ping a host on my internal lan from my ubuntu notebook the host name never resolves, but if I ping www.domainname.xxx it will resolve because our dhcp server is setup as the dns server too. If I use the connect to server tool and select samba share and specify host by name, it can resolve that and the shares show up... same dns server, same machine, but different interface/program. My real reason behind this is because my synergy+ keeps falling over whenever the synergy servers dhcp lease expires and it gets a new I have to then specify the new address and change configs.
View 3 Replies View RelatedI am working behind a http proxy (172.30.x.x:3128). I have configured it in my terminal. All the applications such as wget,lynx firefox etc. are working correctly.However all dns utilities like nslookup, host and even ping too are not working.Following is output of host command:
Code:
root@ding:~# host google.com
;; connection timed out; no servers could be reached
Output of host -T:
[Code]....
To connect to net I have to first run dhclient3(learnt from this forum!).It gives me my ip but where is dns address sent I don't have and idea.
I cannot access/ping my Debian server. I know the IP is right (ifconfig, route and ip addr) all gave me 10.0.2.25 (route gave me 10.0.2.0).I cannot ping it from any computer in my netwerk, even when I try to ping it from my Debian itself, it gives me Destination Host Unreachable !(Wierdly, I can ping 10.0.2.2 tho).I am using virtualbox when the netwerk options 'NAT' turned on. When I look at my /etc/network/interfaces/ the last line looks like:iface eth0 inet dhcpShouldn't their be some other stuff listed?
View 6 Replies View RelatedI had configured Squid in RHEL 5 and facing an issue with pinging. Not able to ping any website,hostname is resolving to ip address but not able to ping
[code]...
I can ping a host on my LAN successfully, but I cannot ping [URL]... for example. I have disabled the firewall and set http_proxy and can browse the internet with "Use system proxy settings" checked in Firefox. I am unable to update with yum either, but I am not sure if this is a side effect or not. I have run a trace on my ip address as I am browsing the internet and I can see the sites I am visiting on our web appliance. However, if I try to ping or update no requests are hitting the proxy so I don't think that is the issue.
View 6 Replies View RelatedI have a machine running linux with 3 ethernet interfaces attached.
My Ifconfig:
My route output:
eth0 is attached to a laptop, eth1 is attached to a PC. eth2 is attached to a DSL modem, and the server is successfully acting as my internet gateway. The trouble is, my PC cannot see my laptop and vice versa. E.G. cannot ping, host seems down.
This is a RHEL 5.4 install. I did a fairly routine install setting up a static IP address of 10.5.96.10, a subnet mask of 255.255.254.0, and a gateway of 10.5.96.1 with the standard DNS setup for this network. These are all standard network setting for this network and otherwise work fine on other systems. The IP, gateway, and subnetmask all appear correctly on all relevant configuration files. This server can not ping any other system on the network and can not ping its default gateway. No other systems can ping this one either. Also this system can not ping "localhost" or its own hostname. The hosts file contains the line:
[code]...
I can ping 127.0.0.1 and 10.5.96.10 and it works fine. Also the firewall is disabled. I know I probably can't get a straight forward fix with the information I have on hand right now, I'm more of a Debian guy, so there might be some Red Hat intricacies I'm not familiar with. I think I had a CentOS install some months back that had this issue and I don't remember how I fixed it, or if I even did. I might have just replaced it with Debian. That's unfortunately not an option this time around since it's not my box.
A brief description of my network:It is a small home network consisting of an Ubuntu 10.04LTS server edition, an Iomega ix2 NAS, a WinXP pro server and several family laptops.This is all routed through a Netgear WNDR3300 home router. All are assigned IP's via DHCP and all but the laptops are static (via DHCP though). The WAN address/DNS is assigned via DHCP from my ISP.The problem:When one of the machines is offline, Ubuntu does not resolve the netbios name correctly. No surprise here. But what is happening is that it is finding some arbitrary machine on another network. Below is what a ping to an offline host reveals:
Code:
ping -c3 hostname
PING hostname (204.232.162.92) 56(84) bytes of data.
[code]....
After I applied below iptables rule.. I am unable to ping the host in 172.16.1.0/24 from OpenVPN client
View 1 Replies View RelatedI have a router which have 4 ethernet ports(eth0,eth1,eth2,eth3,eth4 ) & One ADSL Line & One USB, I need to configure My router eth3 as a WAN & eth0 as a LAN using iperf, I am going to findout test a my Application(using iptables) whether my application is correct or wrong As of now I configured like server pc1(192.168.1.230)--->eth0(gw)(192.168.1.1)Router--eth3(gw)(192.168.2.1) -->pc2(192.168.2.157). For eth3 as a WAN and eth0 as a LAN. But I am not able to ping between two pc's.
View 1 Replies View RelatedI have connected xp and fedora through crossover cable . xp has ip address 192.168.0.1/24 (manually assigned) fedora has 192.168.0.2/24 with default route equal to 192.168.0.1
I can ping fedora from xp computer but i can't able to ping xp from fedora computer.
I have manully edit the /etc/sysconfig/network-scripts/ifcfg-eth0 file with correct subnet mask and ip address because when i tried to give ip address manully in network manager the subnetmask is replaced with gateway address don't know why.
Now i want to share internet through crossover cable . xp is connected to internet through wireless usb adapeter.
I try to use the "ping -a" command for getting an audible ping. But there is just silence The command "beep" works fine, so everything should be ok with the speaker (in the konsole).
View 3 Replies View RelatedI try to ping with php : exec("ping -n 1 $ip",$output[],$retval); it works fine in window. but in linux i got this error : ping: icmp open socket: Operation not permitted are there any ways to solve this ?
View 5 Replies View RelatedThis applies to my 2 opensuse PC's, my Windows PC is fine.I can ping a hostname, say "PC1" but I can not ping PC1.domain.local (even the host PC can not ping it's own FQDN). When I ping just the hostname the ping stats even list the FQDN.Onto the next issue, since all my PC's, have the domain prefix domain.local, my Synology can not. I can ping it's IP and that is it. I can resolve it's name with nmblookup just fine tho and that is what is killing me. How is this not resolving.Even weirder, I can browse to "Synology" in Network Servers under places on the slab.
View 3 Replies View Related