Hardware :: Get A 2nd Display For A PCMIG 1.0 Passive Backplane With An Advantech 6010 CPU?

May 2, 2011

Need to get a 2nd display for a PCMIG 1.0 passive backplane with an Advantech 6010 CPU [onboard video works fine], but NO PCI card will come up as the 2nd display! Tried 11 cards and most leave the cursor at the top corner when doing xorg-configure, but no that's all.

Has anyone gotten a 2nd display to work on a passive backplane system? Tried some newer cards, but they don't even allow the system to POST - perhaps because they are PCI 3.0 and the backplane is PCI 2.0 or 2.1?

View 9 Replies


ADVERTISEMENT

Debian Hardware :: Advantech USB 4761: Invalid Module Format

Jan 20, 2010

I've got a brand new Advantech USB 4761 Digital/Analog PC Lab card. They claim to run under Linux. The install, " dpkg -i advdaq_1.04.0006-1_i386.deb", was successful. But when I tried to modify and run their install script, "adv_load_template", I get this:./adv_load_templateinsmod: error inserting './modules/advdrv_core.ko': -1 Invalid module format insmod: error inserting './modules/usb4761.ko': -1 Invalid module format

View 1 Replies View Related

OpenSUSE Hardware :: Xerox Phaser 6010 USB Printer Not Detected?

Jun 21, 2011

I'm running OpenSuse 11.4 and trying to connect a brand-new Xerox Phaser 6010 printer through USB.

I started by trying Yast>Hardware>Printer>Add, but no printer was detected. I tried "Detect More", but still no printer was detected.

The USB cable is connected, the printer is turned on, and /dev/usb/lp0 exists. There is only one printer on my system, so this must by my printer device; indeed, it disappears when I turn off the printer. Also, the printer works nicely under Windows, so there is no hardware problem with the printer itself.

I tried removing and reinserting the usblp module (using `rmmod usblp; insmod usblp`), but still no printer. Cups does not seem to find it.

I also tried explicitly specifying a URI for the printer using ConnectionWizard>SpecifyArbitraryDeviceURI usb:/dev/usb/lp1, selected the Xerox Phaser 6010 driver (which is present in the list) and tried to print a test page, but nothing happens.

What other options are there to figure out what is wrong and get this printer to work under OpenSuse?

View 9 Replies View Related

Networking :: Making NIC Completely Passive?

Jun 29, 2010

I want to make an Ubuntu box a completely passive sniffer. As such, I want the NIC to never send anything or replying to anyone on the network, while still being able to capture the network traffic using pcap.

View 8 Replies View Related

General :: Code For Passive Clustering In NS 2.34?

Apr 4, 2011

How can I get the NS Code for passive clustering in NS 2.34

View 3 Replies View Related

Software :: Configure Cygwin On Passive Mode?

Dec 26, 2008

I am using Cygwin with RHEL 4. Can anyone guide to configure it on passive mode.

View 2 Replies View Related

Debian Configuration :: Setup Passive Ports And Masqurade?

Aug 27, 2010

my proftpd setup will not do passive ports, reading the how-to on this page [URL] It gives the instructions on how to set up passive ports and masqurade but the example is using ipchains so before I start typing these commands in I would like to know if I need to change anything in the commands other then the ipchains command.

[Code].....

will this work on debian 5.05 also how do I find out if I use ip filters.

View 1 Replies View Related

Networking :: Active FTP Using Raw FTP Commands / Turn Off Passive Mode Using It?

Apr 1, 2009

Can anybody have an idea of an ftp client code using raw ftp commands.

OR
Can anybody tell me how to turn off passive mode using raw ftp commands.
PASV is the command which turns on passive mode but there is no such alternative of active mode.
I have already tried using pasv_enable=NO in vsftpd.conf but that is not working.

View 1 Replies View Related

Networking :: Pure-ftpd Passive Transfers Not Working?

Jun 4, 2010

I have a dns-323 linux device that's running pure-ftpd with SSL/TLS authentication. Pure-ftpd is sitting behind a linksys router with IP 192.168.1.51. Pure-ftpd is configured for port 8021 and passive port range 55562-55663. The linksys router is configure to forward port 8021 and the passive port range to 192.168.1.51.

From outside my network I can connect to the ftp server using the WAN address of the router. I'm using filezilla 2.2.32 as my client and I choose FTP w/ explicit TLS (no other option will connect). The client will authenticate successfully with pure-ftpd but once it sets up the passive data connection and tries to do a LIST of the root directory, there's a timeout. I'm assuming this is because the passive data connection is not working. In pure-ftpd, I tried changing the passive address that it reports, to be the WAN address of the router, but it did not make a difference. I included the log from filezilla below.

[Code]...

View 5 Replies View Related

Fedora Networking :: IPtables Passive Ftp Rules Donot Work?

Aug 15, 2011

I'm trying to build a firewall with IPTables: INTERNET <--------> (eth0) FIREWALL (eth1) <------------->FTP_srvI set all rules DROP by default.My rules for forwarding packet to FTP server:

#iptables -t nat -A PREROUTING -i eth1 -d $FIREWALL_EX_ADDR -p tcp --dport 21 -j DNAT --to-destination $FTP_ADDR:21
#iptables -A FORWARD -i eth0 -o eth1 -p tcp --dport 21 -m state --state NEW,ESTABLISHED,RELATED -j ACCEPT

[code]....

View 2 Replies View Related

Server :: Drbd Active-passive Cluster Change Primary One?

May 21, 2011

i have a two node drbd cluster, while drbd1 is primary and drbd2 is slave i should make drbd1 slave and unmount drbd partition and make make drbd2 primary and mount drbd partition to see content on drbd2is it any way to automate it so as drbd1 goes down, drbd1 make itself primary and mount the partition?

View 2 Replies View Related

Server :: Run A Ftp On Default Ports With Port 10100-10199 As Passive?

Feb 19, 2010

tring to run an ftp server on default ports with port 10100-10199 as passive. Using vsftp. But the ports refuse to open what the heck am I doing wrong? see screen shot. oh using karmac, now.

View 2 Replies View Related

Server :: Nagios Passive Or Remote-host-side Alert?

Jan 6, 2010

Is this possible that a process running on a remote-host only inform nagios when some thing is wrong. Rather then nagios-monitoring-server checking through NRPE every so often. Reason is I want to add too many alerts in the application. And I don't want a whole list of ok messages.

View 1 Replies View Related

OpenSUSE Network :: Uploading Files To Remote FTP Server Using Passive Mode With Enabled SuSeFirewall2

Feb 28, 2010

I've got problems uploading files to a remote FTP server using passive mode with enabled SuSeFirewall2 (Using 11.2)

I've disabled Firewall and everything went ok. Why firewall disables or terminates OUTGOING connections to a remote FTP?

View 7 Replies View Related

OpenSUSE :: 11.4 Gnome 2.3 Display - CRTC Error That The Display Is Over The Maximum - 1920x1920

Apr 16, 2011

I have a fresh install of OpenSUSE 11.4 64bit and I have installed the AMD Display drivers for my Radeon HD 5970. Everything seems to be working quite well. I have a multiple monitor setup (1280x1024 monitor and a 1920x1080 monitor).

I have my primary display set to 1920x1080, however when I try to enable the second display, I get a CRTC error that the display is over the maximum (1920x1920). If I enable both monitors at lower resolutions, there is no problem.

I have done a fair bit of reading and have been unable to determine where this maximum is set, or how to change it. I'd like to be able to run both monitors at their native resolutions.

View 3 Replies View Related

General :: Know Which Display Number For The Variable DISPLAY To Be Exported When Ssh To Server?

Dec 26, 2010

When i ssh to server using -X, i always confuse about which display number i should export. It seems to me sometimes the display number has been used by something, so what i can do is only

export DISPLAY=localhost:0 && xclock
export DISPLAY=localhost:1 && xclock
export DISPLAY=localhost:2 && xclock

[code]....

View 1 Replies View Related

Ubuntu :: HD4870 Dual Display - Cannot Seem To Swap My Primary Display

Jan 8, 2010

Hi I am new to ubuntu and am having major problems setting my displays up. my setup is a hd TV to the Left of my pc monitor, i have managed to configure catalyst to let me have a main display with the second display being an extension of the first, the problem is i cannot seem to swap my primary display, at the minute my HDTV has all the taskbars and everything on it while my pc monitor is just a blank background, i would like it so i could start a film playing for my children, then drag it across to the HDTV while i can still use my pc in the background.

View 1 Replies View Related

Fedora :: System-config-display Just Ruined Display?

Jun 29, 2010

I did not have any /etc/X11/xorg.conf, so I read on these forums that system-config-display would create one for me. I ran system-config-display and it created an xorg.conf. But now my display is all messed up!! So, I deleted the xorg.conf and nothing changed. Why on earth would the display still be messed up if I deleted the file that was causing it?? Does system-config-display change somethign else?

View 14 Replies View Related

Ubuntu :: Display Driver - Cannot Get Display Settings Nvidia7600GS?

Jan 28, 2010

I am using GeForce 7600 GSNot using the Nvidia X driver message you know... I searched all over, and seen this problem on many searches but no resolve issues.I want to be able to connect my tv, I use to be able to when I first installed Ubuntu and now IdK.

View 3 Replies View Related

General :: X11 Forwarding - Error: Can't Open Display: <ip Of Display>

Jun 28, 2011

I have the following scenario that doesn't seem to work normally. I have a windows 7 pc from which I am using putty to connect to my other linux servers (all running redhat 5 and 6). So here is the scenario that works and one that does not work. And I'm trying to figure out the one that does not work. Scenario that works:

From windows 7 (putty) I ssh into Linux_Server_1.
echo $DISPLAY
localhost:10.0

I run xclock and I see it pop up on my windows 7 pc. I am using xming on windows 7 to help me populate the display from linux to windows. One that does not work:

From windows 7 (putty) I ssh into Linux_Server_1. Then from Linux_Server_1 I ssh into Linux_Server_2.
echo $DISPLAY
<no output>

I try to setup $DISPLAY with localhost:10.0 or 0.0 or even my windows 7 pc ip address:0.0 ....etc Then when I try to run xclock I doesn't work.

I get these error messages: Error: Can't open display: <ip of display>

Also as a side note all our Linux servers are sitting on one subnet. My pc is sitting on another subnet. I use vpn to connect to the subnet where the servers sit from my pc.

View 4 Replies View Related

Fedora :: Display All Disks And Partitions Available In A GUI Display

Dec 1, 2010

I have installed Fedora 14 Security Spin, and want to display all disks & partitions available in a GUI display. How can I achieve that?

View 1 Replies View Related

Programming :: HTML5 "details" Tag Display - Inline - Display - Hidden CSS Ignored - Firefox - Seamonkey

Jan 11, 2011

I'm testing HTML5 for the first time, using Firefox (beta) 4.0b8 and SeaMonkey (beta) 2.1b1, and its ignoring some CSS. Specifically, I have problems with the <details> tag. (It is nested in a paragraph...I am using it to provide an in-paragraph definition in hopes it can be toggled.)

Firefox only partly supports <details>. It's not supposed to show anything except the content of <summary>, unless you click on <summary>'s content. Instead, it puts a line break before the content of <details>, splitting the paragraph in two peices (which looks silly), without the "closed/open" functionality.

So I tried using "display:inline" in my CSS, but that gets ignored. Just for fun, I also tried "display:hidden" (also ignored) and "display:none" (obeyed).

SeaMonkey doesn't doesn't do anything special with the content of <display>...but it also ignores the same CSS as Firefox.

The only thing I can do to support semantic design is apply "font-style:italic" to all <details> elements.

Granted, you might ask, "why bother using <details> at all. then?" Well, I would like to have <details> for the browsers that support it, with the "font-style:italic" to degrade the page nicely for those that don't (such as for SeaMonkey).

Does anyone know why "display:inline" and "display:hidden" get ignored?

View 1 Replies View Related

Ubuntu Networking :: Set Display And Xhost: Unable To Open Display "XXX.XXX.X.XXX:0.0"

Jul 20, 2011

I have configured an instance in AWS EC2. I am trying to set the display back so I can run x apps. I login using ssh -xy -i...

export DISPLAY=XXX.XXX.X.XXX:0.0
echo $DISPLAY to verify
xhost +
xhost: unable to open display "XXX.XXX.X.XXX:0.0"

I have commented out nolisten tcp as suggested HERE I have modified /etc/gdm/custom.conf as suggested HERE Actually, the last suggested modifying /etc/gdm/gdm.conf, but that file didn't exist, so I added the line: DisallowTCP=false to /etc/gdm/custom.conf I rebooted, and still I get: xhost: unable to open display "XXX.XXX.X.XXX:0.0"

View 2 Replies View Related

Ubuntu :: Xterm XT Error: Can't Open Display: Xterm: Display Is Not Set

Aug 20, 2010

I've just installed xterm, ant trying to run it from my windows machine using ssh. I have X11Forwarding yes on /etc/ssh/sshd_config when I use, MobaXterm, np, I can use xterm after I log ssh -X xxx

but when I use Cygwin, and do ssh -X xxx, and then xterm, I have: xterm XT error : Can't open display: xterm: Display is not set

View 3 Replies View Related

Ubuntu :: Kernel Spamming Logs Full "display Port Opened" And "display Port Closed"?

Apr 4, 2011

I have the following problem: syslog is constantly writing to disk, because the kernel spams these messages

Code:
Apr 4 14:14:56 aspire kernel: [138498.252610] display port opened
Apr 4 14:14:56 aspire kernel: [138498.299755] display port closed
Apr 4 14:14:57 aspire kernel: [138499.328206] display port opened
Apr 4 14:14:57 aspire kernel: [138499.371835] display port closed
Apr 4 14:14:58 aspire kernel: [138500.452671] display port opened

[Code]...

View 1 Replies View Related

General :: Shell Scripting \ (test If A File Is Empty, If It Is Then Display "file Is Empty" Otherwise Display "file Is Not Empty")?

Oct 5, 2010

I am a final year student doign Computer systems engineering and just been introduced to linux. While still strugling to catch up with the commands, I am now given an assignment under shell scripting.I seriously am strugling to understand this question, can you please assist me.Here follows the assignment:

Operating Systems III
Some tips
e.g. (test if a file is empty, if it is then display "file is empty" otherwise display

[code]....

View 10 Replies View Related

Ubuntu :: Cannot Run Display / What To Fix It?

Jun 15, 2010

I try to boot my computer, it starts, it starts loading ubuntu. But all i get is this full screen terminal thingy prompting me to log in. So i do, and well. There's still just a terminal. I try writing "Nautilus" and get the error that display cannot be run. I try writing "GKSUDO nautilus" and get the same error, with a little difference.

What should i do?

View 4 Replies View Related

Ubuntu :: No Display With VNC?

Mar 1, 2011

I could use UltraVNCViewer from XP Pro and Server 2008 to control the Ubuntu 10.10 desktop. The computer has not been turned off, but when I log in with UltraVNC Viewer, all looks fine but no display. I have a black screen with the mouse cursor I can move with the mouse on the XP computer.

I can still access the mapped drives on the Ubuntu Desktop, there are no errors when connecting, but no display.

View 1 Replies View Related

Ubuntu :: Don't See Any Display

Mar 1, 2011

I just installed Ubuntu 10.10 on my PC. When I start the computer, GRUB pops up and I select the top Ubuntu one, but then I don't see any display. I hear the sounds of the login screen, I can login in and continue, but I still don't see anything on the screen, and my monitor goes to sleep.

some specs:
intel Core 2 Duo
1 TB Hard Drive (Windows 7)
500 GB Hard Drive (Ubuntu 10.10)
nvidia GeForce 8400 graphics card

View 7 Replies View Related

General :: Getting X11 To Display In 8-bit?

Jun 30, 2010

I've been told to use an old Electron Microscopy program that needs to display in 8-bit.When I install and try to run I get the error

Searching for 8 bit PseudoColor visual ...
Searching for 6-bit PseudoColour visual ...
Searching for 24-bit DirectColor visual ...
No matching visual available.

How do I get Suse 11.2 (my dist.) to show something that has such a requirement? I found something on the web for Mac where they said use xquartz to and quartz-wm but I don't think these work in Suse(?). I also went fooling around on Sax11 and couldn't really find anything.

View 10 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved