General :: Serial And Parallel Data Communication On Fedora 13

Apr 22, 2010

I have been trying out serial and parallel data communication on Fedora 13 Beta. I can easily see the list of serial ports through:

Code:
setserial -g /dev/ttyS[0-3]
And can also write some data through:
Code:
ll > /dev/ttyS0
But I am unable to see parallel ports
I can see something like:
Code:
/dev/parport0
But when I try out:
ll > /dev/parport0
It throws error.

View 3 Replies


ADVERTISEMENT

Programming :: Serial Port Communication Program Always Lose One Byte Data: 0x00?

Dec 13, 2009

I wrote a serial port communication program to access a equipment.

int main(void)
{
int fd = 0;
int nread = 0,i = 0,nwrite = 0, tmpread = 0, m = 0, n = 0 ;

[code]....

View 2 Replies View Related

General :: Parallel Port Communication With RHEL6 Not Working?

Dec 13, 2010

I was trying out the parallel port communication on RHEL 6 but found it not working:
#echo hello > /dev/parport0
write error :Invalid argument".
#ll > "/dev/lp0"
/dev/lp0:No such device or address

View 2 Replies View Related

General :: Serial Communication In Between VM And ESX?

Apr 28, 2010

I am in verse to understand the serial communication between guest and host.I have just added a serial port through VI Client selecting "Use serial port on host"(host being ESX host).If I am on VM and run :

ll > /dev/ttyS0

I understand that it should get displayed through ESX Host. So On ESX Host, I typed:

cat /dev/ttyS0

But nothing worked !

View 1 Replies View Related

General :: Palm Vx & Serial Mouse Communication ?

Apr 25, 2011

When I try to Sync a Palm Vx to my PC through serial port I get a communication error message in the gadget. My PalmOS Devices application is already configured to use tty0 or tty1 in unsuccessfully trials. I have a lot of information in the addresses, agenda, notes, etc. and do not want to loose that information gathered for years, nor to return to Windows.

As a test, I used a serial mouse in the serial port and It didn't work. I verified the Bios Setup and COM 1 and COM 2 are enabled.

I also checked my system serial support with the following commands:

And messages were OK when compared with typical outputs. My machine is a Pentium 4 CPU 1.6 GHz, in a U8668 motherboard (Award Software International). I have Ubuntu 10.04 LTS with Gnome.

I am new in Linux and don't know Bash yet. I had followed indications from Internet tutorials successfully, but I don't know how to proceed in this case.

View 1 Replies View Related

General :: Establish Serial Port Communication Through USB In System?

Jun 30, 2011

I am new to Ubuntu and I need to establish a serial port communication between my PC and microcontroller MSP430G2452.

On connection the USB available with the Launchpad and using lsusb.

It identifies the port as:

Bus 005 Device 003: ID 0451:f432 Texas Instruments, Inc. eZ430 Development Tool

After establishing such a connection what I need to do? My aim is to send a byte of information in Linux.

View 1 Replies View Related

Red Hat / Fedora :: How To Change From Serial To Parallel Mode On Cluster

Jun 10, 2010

I compiled a code on a Linux cluster machine with mpich and ifort. A test run shows that the program works fine. However, it seems that the program is running in serial instead of parallel mode: reducing the number of CPU's from 32 to 3 does not increase the time it takes to run the simulation. Infact, the simulation is slightly faster with 3 compared to 32 CPU's. Unfortunately I have very little experience on the subject.

My questions are:

(1) How can I be 100% sure my code is running in parallel and not in serial mode?

(2) If the code is running serial, what do I need to do to make it run in parallel mode?

Details:

For submission I use a jobscript which includes the following lines:

Red Hat 4.1.2-46

View 1 Replies View Related

Hardware :: Serial Communication Only Works In One Direction - Why Is So?

Sep 21, 2010

Running RHEL5.5 on a Dell R710 server. I installed a 2-port PCIe serial card, built the driver, and installed the kernel module. The ports show up in /etc/hwconf, lspci, kudzu, /proc/ioports, etc., and I now have two new device entries...

/dev/ttyE0
/dev/ttyE1

When I connect a null modem cable from port 0 of the card in the new computer to serial 0 of another computer, I can receive text from the other computer. When I do this... code...

View 2 Replies View Related

Ubuntu :: Open The COM1 Port To Do Serial Communication Via PHP?

Mar 15, 2010

Not really sure where to post this, so here goes... I installed apache2, php and MySQL via LAMP and everything seems to work fine but when I try to open the COM1 port to do serial communication via PHP, I get a permission denied error.

'mode com1: BAUD=9600 PARITY=N data=8 stop=1 xon=off';
$fp=fopen("COM1:","w+");

I've also tried using /dev/ttyS0 instead of COM1: but no luck. Anyone out there know what I'm doing wrong? I don't know if I need to set something up in apache2 or php or if the code is just wrong. I'm on an Acer Aspire One with Ubuntu's LNR 9.10.

View 6 Replies View Related

Networking :: Setting Up Serial Communication From Desktop Through USB Port In Terminal?

Jan 15, 2010

I am new to linux terminal programming and all but i want to set up a simple serial communication from my desktop through USB port. The actual idea to to write some data in the terminal and build a terminal program that sends the data to the usb port with a fixed baud rate. are there ready made terminal programs available for this simple communication?or atleast any Graphical tools which could help me build and design such a terminal in ubuntu 9.04?

View 8 Replies View Related

Programming :: Communication Data Between Different Process

Nov 22, 2010

I would like to send struct data from process A to process B but I dont known what is the best way. I have read about IPC, but there are a lot of ways to do it.

View 2 Replies View Related

Programming :: Send /receive Data Through Serial Port In Fedora?

Dec 27, 2010

I am doing work on serial port. I want to send/receive data to/from Microcontrolar through serial port. But I don't know how to initialize, receive and send data to Serial port. i am new in fedora so i hav'nt any deep concept of fedora.can anyone send me C code , which communicate through serial port in fedora (or atleast help me). I am using Fedora 11.

View 6 Replies View Related

Networking :: Serial Port : Read Data, Not Reading Complete Data?

Mar 5, 2010

I have an application where I am sending data via serial port from PC1 (Java App) and reading that data in PC2 (C++ App). The problem that I am facing is that my PC2 (C++ App) is not able to read complete data sent by PC1 i.e. from my PC1 I am sending 190 bytes but PC2 is able to read close to 140 bytes though I am trying to read in a loop.Below is code snippet of my C++ AppOpen the connection to serial port

Code:
serialfd = open( serialPortName.c_str(), O_RDWR | O_NOCTTY | O_NDELAY);
if (serialfd == -1)

[code]...

View 5 Replies View Related

Programming :: Get Data From Serial Port Function Read() Blocks When Data Not Available?

Jun 11, 2009

I am using read() in c++ to get data from a serial port. However, if no data is available on the serial port the function blocks until dta arrives.Example code:

//------------------------------------------------------------
char m_readBuffer[255] = {0};
char* p_curChar = m_readBuffer;

[code]...

View 1 Replies View Related

Networking :: Data Transfer In V2V Communication (Fedora11)

Feb 27, 2010

i am using NCTUns simulator and having problem while receiving message from an OBU. sending a message works properly but recving creates problem and fails. i am using exactly the same function as used by the developers in the demos but still no luck. i copy the code attch the screen shots to have a look

sendto() and recvfrom() are used for message transfer. they both return >-1 if they are executed successfully. please have a look in the screenshots. agentClientReportStatus is the built in packet format which im using here whose fields i filled manually are in the code below.

agentClientReportStatus *message,*mssg;
int remainTime,n,n2,n3,i,sendingaddress,value;
sockaddr_in cli_addr;
timeval now;

[Code].....

View 3 Replies View Related

Programming :: Appropriate Interprocess Communication With Data Preservation?

May 29, 2011

I am searching for an interprocess communication that is platform and language independent and is two way communication among different processes and the most important thing is the ipc should have the ability to store data until the receiver receives it.

View 2 Replies View Related

General :: Redirecting Serial Data To An External Devices Using Bluetooth?

Apr 24, 2010

i have the following challenge: i have a Bluetooth GPS device that i have connected to my linux notebook. but now i also want to use the same device (or better, GPS data stream) for my Navigation device (HP Ipaq with TomTom). make an serial port bluetooth service (sending) that my Navigation device can connect to. copy the incoming bluetooth serial port data stream to the outgoing bluetooth serial port.

i have already installed GPSD so i have the TCP port where the GPS data is available for everything on my notebook. but now i also want it to send it out through bluetooth.

1. is there someone out there who already did this?

2. how to make an bluetooth serial port service on Fedora 12?

3. how to copy a data stream from 1 device to the next device?

View 1 Replies View Related

General :: Minicom Shows Offline And Is Not Capturing The Serial Data Being Sent?

Jan 5, 2011

Minicom was running fine two days ago capturing data from a gage device via a serial cable. Yesterday, users of the data started complaining that they were not receiving any data.

The minicom status line reads offline. Is this part of the problem or is this normal (I never really noticed it before.) All settings on the gage device match the minicom settings.

View 3 Replies View Related

Programming :: Parallel Data Transfer Using Sockets

Feb 25, 2011

I am doing a project where 2 clients connect to server and communicate (chat) and transfer data one after other using sockets. I have working code for this in C language. Now our main aim is to create a communication link where two clients transfer multiple streams data parallely. To be more precise i want to transfer images files and audio files parallel at same time, so is it possible to send data parallel using one socket connection?

View 3 Replies View Related

Software :: Serial Printer Setup 7 Data Bits Rx 8 Data Bits Tx

Aug 8, 2010

About 7 years ago I setup a Redhat system with 8 serial terminals and 8 serial printers, this is still running but I need to get another system running so the original can be taken down for maintenance. The printers are ancient Newbury data dot matrix wide carriage with 7 data bits receive 8 data bits transmit Xon/Xoff flow control. Now I remember setting the transmit and receive data bits as above but after 7 years can't remember where.

View 2 Replies View Related

General :: Windows With Putty Via USB Serial Cable To Serial Port - Output Ok, Input Isn't?

Jan 13, 2010

I am trying to get two way serial communications going between a Windows XP system and a Linux system (RHEL 5).I have /sbin/agetty -L 9600 ttyS0

in /etc/inittab. I am using a generic USB to serial adaptor on Windows (Unitek) and a null modem cable. I have putty configured for 9600 baud, 8 bits, no parity, one stop bit, no flow control.I get the login prompt from agetty in the putty window but input does not work; I see weird characters in the putty screen. I can echo output into the device from windows and see it, but

cat < /dev/ttyS0. just prints out weird characters from what I type.

View 3 Replies View Related

Programming :: Intercept Data On Serial Port?

Dec 21, 2010

I dont know if this is the right forum, But I try to find a solution, I want to intercept data from/to serial port without disrupting the software that manages the serial port, (I would like to save the data to a file or sent into a socket) I searched somes modules and programs (linspy, ttysniff, interceptty, maxty ...), A bit complicated (There are some diff. between kernel 2.4 and 2.6), So I'd like to change the serial port driver to intercept the "read" and "write " and do what I want with the data, I'd like to know what do you think about

View 3 Replies View Related

Programming :: Send Data Through Serial Port Using C?

Oct 20, 2009

I am not a profession programmer. I have to write a C code which send some command to attach display using C program. Can any one please help me in this regard.

View 3 Replies View Related

Networking :: Serial Port : Not Able To Write Big Chunk Of Data?

Mar 10, 2010

I am trying to send text data from one PC to other using Serial cable. One of the PC is running linux and I am sending data from it using write(2) system call. The log size is approx 65K bytes but the write(2) system call returns some 4K bytes (i.e. this much amount of data is getting transferred). I tried breaking the data in chunks of 4K but write(2) returns -1.My question is that "Is there any buffer limit for writing data on serial port? or can I send data of any size?. Also do I need to continously read data from other PC as I write 4K chunk of data"Do I need to do any special configuration in termios structure for sending (huge) data?

View 4 Replies View Related

Programming :: Displaying I/O Possible When Reading Data From The Serial Port?

Aug 31, 2009

I have got a problem while reading from the serial port. I'm working on iMX-31 board and Eclipse IDE. Whenever I'm trying to read any data through the serial port, it's displaying I/O Possible and the application is being terminated. After reading I'm trying to write this data on a file. Here are the excerpts from the code:

# int main()
{
if (openport()<0)

[code]...

View 7 Replies View Related

Programming :: Serial Port Program Not Outputting The Right Data?

Apr 11, 2009

I have connected a device to my linux system with a serial cable (rs232). The settings are: port /dev/ttyS0, baud rate=38400, data bits=8, stop bits=1, no parity, no hardware or software handshaking. I wrote a linux program that sends 1 byte to the device, but the device doesn't receive it. I know the serial ports are working because when I use the CuteCOM application to send data, the device DOES receive it, so obviously it is a problem with my code..

Code:

#include <stdio.h>
#include <stdlib.h>
#include <math.h>

[code].....

View 2 Replies View Related

Programming :: Read Some Data From Controller Using Serial Port?

Aug 25, 2010

i want to try with a small application in linu in that i want to read some data from controller using serial port and i wanna transfor that data to another meachin in the network for this i want serial port interfacing programming as well as socket programming.

View 1 Replies View Related

Programming :: Serial Port Data Read Time Interval?

Oct 30, 2010

I am writing a C program which reads data over serial port. While reading data, if I send my data(which is a 13 byte structure) periodic with a period of 1 second for 10 times I read it without problem and I read the data 10 times as I sent and as I expectBut if I send data continuousuly(without any time interval between each sending) 10 times I can only read 1 of them(I can only read it once).

View 11 Replies View Related

Debian Hardware :: USB Serial Adapter Spontaneously Emitting Data Every 20 Secs

Jul 13, 2015

I tried connecting my Debian laptop to a vintage Apple //e using a Super Serial Card on the Apple side and a USB to serial adapter on the laptop side. It kind of works -- I can send data over to the Apple using e.g. echo "foobar" > /dev/ttyUSB0 or via minicom --, but every 20 seconds (quite exactly!) some 4 random characters appear on the Apple's screen (mostly tildes, sometimes a pipe). This does *not* happen when booting the laptop into Debian rescue mode; so I guess it must be some (daemon?) process messing around with the usb serial device in regular intervals.

I tried to disable quite some services, but the problem remains.I don't have any clue how I might catch the evil-doer in the act -- virtually all serial monitors I've so far read about allow only monitoring the interaction of a known program/process with a serial port. But in this case I first have to actually find out which process is talking to the serial port in the first place.

View 4 Replies View Related

Programming :: Debian Serial Port Read() Return Wrong Data?

Jul 6, 2010

I am implementing a simple serial protocol where my ARM9 board, running Linux is communicating to a slave peripheral board. The Master sends a 12 byte data stream and the peripheral board returns status in a 23 byte response. The serial port is opened in raw mode. It works perfectly on 44 reads; however, on the 45 read the data returned from the read() is incorrect. I've framed what's being sent on an oscope and it is correct.The coincidence is that 23 x 44 = 1012. It's as though the receive buffer is 1K and when I go past the boundary I get bad data. The read following the bad one is good again.I've tried flushing the buffer before reading but get the same result.Here's the port initialization code:

Code:
int initport(int fd)
{

[code]...

View 4 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved