i use fedora11 and try to use wireless i find driver for chip Realtek RTL8187 but want to know command to install it. i save folder of driver on desktop in folder name rtl8187_linux_26.1010.0622.2006has like this
[Code]....
How do I install my driver wlan in Fedora 14? I use this notebook hp:
http://h10025.www1.hp.com/ewfrf/wc/p...reg_R1002_USEN
I have already installed the update of fedora and still does not work.
I've got Fedora 14 (2.6.35.12-90.fc14.i686.PAE) installed and i'm trying to use hostapd with my Realtek RTL8191S USB WLAN Adapter, but can't get it to work. The driver i'm using is : rtl8712_8188_8191_8192SU_usb_linux_v2.6.0006.20100 601.tar.gz
[Code]....
just swapping all my computers over to linux as it far far better than anything i've used before. Have the above driver as identified in lsusb.[URL].. Downloaded the linux driver but dont know what to do from here. Tried doing it the windows inf file way but that didnt work. Or more like i couldnt get it working.
View 9 Replies View RelatedThere seems to be some trouble with 8139too not working in a previous post. Has anyone found a solution to this? ubuntu version 2.6.24 (Hardy Heron?). Followed all known possibilities but information is all mostly out of date. module 8139too.ok? does not load. Following makefile on 8139too.c supplied, after altering to suit my version, comes up with 3 pages of errors?. ifconfig shows nothing for eth0like the last person markjuggles i have hit a brick wall here. Am I wasting my time?
View 10 Replies View RelatedI have a ThinkPad x100e with a wireless card.Code:03:00.0 Network controller: Realtek Semiconductor Co., Ltd. Device 8172 (rev 10)my problem is that I can't connect to my wireless network with Gentoo. I've been running Slackware64-13.1 on this computer and now have Windows 7, Ubuntu and Gentoo installed. Slackware, Ubuntu as well as Windows 7 connect to the wlan without problems. I'm using the driver rtl8192se, the module is loaded r8192se_pci and is the same with Slackware and Ubuntu.
I've read many posts and found that other people experience problems with Realtek wlandevices as well. But I have no Idea how to get connected with Gentoo at my wlan. It looks like that the netbook is connected for a very short time, but when dhcpcd broadcasts for a lease the connection is already closed.
I hope I'm posting in the right forum here, but I'm trying to install a realtek wireless driver and make goes okay, but when I get to make install it says permission denied when trying to create a file in a folder near the end of the process. Is there anyway to fix this? What can I do?
View 2 Replies View RelatedI have a Toshiba Satellite L305-SP6944C, Pentium Dual Core 2.16, 2GB RAM, 160GB hard drive, DVD-RAM UJ880AS, display 15.6 TFT widescreen, ethernet Realtek RTL8101E/RTL8102E PCI Express, WLAN Realtek RLT8187, Opensuse 11.2 and KDE 4.3.1. Installation was OK and finally the wireless card is working... but I don't have conectivity bacause in the browser (Firefox) appears a message saying "the server can't be found"
I follow the howto write by Swerdna. With ndiswrapper I install the XP driver for RLT8187, KnetworkManager is in charge of connections showing both eth0 and wlan0, the wireless sign of router Dlink DIR-280 is OK, in the dialog box of network connection I put the mac address of the wlan card but I think that is not the problem.
Other thing that I missed is that I don't find boot.ini at any directory to add modprobe ndiswrapper in the boot sequence, in etc/init.d/ appears a "boot" file, is this file that I have to change to modprobe ndiswrapper??
I just checked the Realtek website and they have a new Linux Driver for the RTL8185. The new driver is dated 6/26/2009. So it is quite recent. I would have thought it might have gotten into FC11.
I have 2 questions. Has anyone tried it? What would be the steps to install it?
I have Ubuntu 10.04 installed and can browse the internet via cable, but wireless isnt working. My wireless driver is "Broadcom 802.11b/g WLAN".
In the windows device manager, I found the corresponding inf file to be oem20.inf which I tried to install it through "Setup Windows Driver" but it gave an error saying invalid driver. I also tried installing the Broadcom STA driver, but that didnot help.
I am dual booting with Windows 7, and i installed ubuntu through the windows wubi installer. My laptop is HP Pavilion dv4. I have installed the regular Ubuntu desktop and have made all upgrades. The results from lspci command i have added below.
gowda@ubuntu:~$ lspci
00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07)
00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 07)
[Code].....
(For the record, I have already read the other threads. Either they don't work for me or are too difficult.) My laptop is an Acer TravelMate 250. I have installed Ubuntu 10.10 (2.6.35-28 generic i686) after erasing Windows 7. At first, the usb wireless adapter worked. Then, I restarted the PC because of some updates and it didn't work anymore. In "edit connections" I find "Auto SpeedTouch8350DB" which is the wireless connection (on my sis's computer it works). When it tries to connect, I'm asked the password but it doesn't work.
[Code]...
I've got a Puppy system running version 4.3.0 that I'm trying to get on the home network. I'm using a D-Link DWA-130 (H/W revision C), which has a Realtek RTL8192U chipset. I got the drivers off of D-Link's website, and they compiled and installed just fine, but when either a) I try to connect to the network, or b) while I'm browsing the web, the system locks up completely. No mouse, no keyboard, no Ctrl-Alt-Bksp to get out of X, nothing.
I'll outline my steps: Install Puppy using a "Full" HDD install (not "Frugal"). Copy the "devx_430.sfs" file (which I got from the Puppy website) from a thumb drive to the "my-documents" folder (although the exact location proabably doesn't matter). Mount it, cd to the mounted directory and execute "cp -a --remove-destination ./* /" and "sync". Copy the kernel source for 2.6.30.5 ("kernel_src-2.6.30.5-patched.sfs4.sfs") to the same directory. Mount it and execute the same commands as before. Copy the folder containing the RTL8192U drivers ("rtl8192u_linux_2.6.0006.1031.2008") to the root directory (i.e. "/"). cd to the folder in the terminal and run "make", "make install".Reboot the machine. Set up networking using the Puppy Internet Connection Wizard. HERE'S WHERE IT SCREWS UP: It connects, but after a while (e.g. just after logging into LQ through it, as a test) it freezes the entire system.
I have to do a hard reboot ("panic button"), then a soft reboot (for some odd reason the usb module won't load after a hard reboot, so the mouse won't work) to get the system working again, only to have it lock up again once it connects to the network.
Are these drivers broken? Outdated? Is there anything I can do to fix this? EDIT: I should add that this only occurs when the adapter is plugged in. If I boot the system with it unplugged, it works fine (probably because it never loads the kernel module).
I just installed FC14 on an ASUS Eee Pc with Realtek WNIC (RTL8191SE) and I am trying to install the driver for the WNIC which I downloaded from Realtek's website. There is a problem though during the 'make' command and this is the output
[code]...
what is this 'build' that is looking for? what can I do to fix this?
How can i install Realtek HD Audio Driver??
I Downloaded The Driver From Realtek Website
http://img517.imageshack.us/i/20100827183305.png/
Then
http://img821.imageshack.us/i/98431356.png/
i dont know how to install this driver from this file
i want to use my Sound Card Features ( like Windows 7)
Ex.
http://smg.photobucket.com/albums/v1...ealtekHDMI.jpg
trying to get my little Encore USB wireless adapter to work on several flavors of Linux (Ubuntu 10,10, ElementOS, Xubuntu, and Puppy), I emailed tech support at Realtek. I asked where is the Linux driver for this product? I did this because there were no Linux drivers posted on their site and everyone here (and on Newegg) is jumping though hoops trying to get a working wireless connection with the Encore and similar dongles that use the RT8187b chipset. I didn't expect an answer, but felt better after my little vent. I get an email from Realtek with a driver. Realtek needs to promote Jerry -- a beacon of customer service in the age of the "get lost" school of customer relations. I have attached the driver below. Caveat: I have not yet compiled the driver, so I don't know much more about it than I've said already, although the archive appears to contain the source code.
View 3 Replies View RelatedI want to install this URL...How to? Because i downloaded the tar.gz2 format of it.And i dont know what to do.
View 2 Replies View RelatedI am using ubuntu 10.04lts on my compaq615 laptop, which has a realtek wireless card, with which I had a few issues to get it to work.
Here is what I had to do:
When I do this, it works beautifully, after setting my router to open I may add.
So, as I said it is probably the fastest wireless I have ever experienced, but my problem is this, everytime I switch my laptop on I have to re-install, starting at:
when I updated from 10.04 to 10.10 beta, I lost my wireless on my Gateway MX3410 laptop. In 10.04, the wireless Realtek RTL8185 card was auto-detected, worked with the default driver.
So I installed the linux driver version of Realtek RTL8185. Although the driver shows up in the "Additional Drivers" panel under "Administration", the computer is not recognising the driver.
Below is all the specs of the current situation.
Gateway MX3410 Computer
OS: Ubuntu maverick (development branch)
2.6.35-22-generic x86_64
lspci:
Ethernet controller: Realtek Semiconductor Co., Ltd. RTL-8185 IEEE 802.11a/b/g Wireless LAN Controller (rev 20)
lsusb:
Bus 002 Device 001: ID 1d6b:0001 Linux Foundation 1.1 root hub
Bus 001 Device 001: ID 1d6b:0002 Linux Foundation 2.0 root hub
[Code]....
I printed off the Readme file from RealTec and went though the following procedure. If anyone spots a glaring error could you please advise and I will try and fix. I changed to superuse using : sudo su and entered my password. All good so far.I was already in the directory containing the downloaded RealTec driver. I downloaded RLT8192SE ver 0019 as this was the closest to my hardware version and the latest driver available.
I used the command : make
and then : make install
Both these commands ran ok. However when I rebooted and activated wireless using Fn F10 on the laptop I was still disconnected from WIFI.
I then used : iwconfig wlan0 up
but this resulted in an error (see below)
root@Ubuntu:/home/jon/LDD/Drivers/test# iwconfig wlan0 up
iwconfig: unknown command "up"
root@Ubuntu:/home/jon/LDD/Drivers/test# ifconfig wlan0 up
SIOCSIFFLAGS: Operation not permitted
my Ethernet card stopped responding a few days after installing Ralink Wireless Card Driver for Linux. I have tried installing the drivers from Realtek's site, but it fails. I also have tried reinstalling the network manager, and that still didn't help any. I have also tried looking online for any post or blog that could help, but that also turned up nothing. The Computer is a new 2010 / 2011 (bought it on new years eve) HP Pavilion desktop that came with windows preinstalled.
View 6 Replies View RelatedRealtek 8111 / 8168 LAN Driver will not install on RHEL 5
[root@localhost r8169-6.002.00]# make clean modules
make -C src/ clean
make[1]: Entering directory `/root/r8169-6.002.00/src'
rm -rf *.o *.ko *~ core* .dep* .*.d .*.cmd *.mod.c *.a *.s .*.flags .tmp_versions Module.symvers rset
make[1]: Leaving directory `/root/r8169-6.002.00/src'
make -C src/ modules
[Code]....
I've just installed Ubuntu 10.04 on my samsung n150. It has the 8192 device in it. Have installed ndiswrapper, however cannot get the drivers for it. How to fix/where to get the driver from so I can get my wireless card working again.
On lspci:
00:00.0 Host bridge: Intel Corporation N10 Family DMI Bridge
00:02.0 VGA compatible controller: Intel Corporation N10 Family Integrated Graphics Controller
00:02.1 Display controller: Intel Corporation N10 Family Integrated Graphics Controller
00:1b.0 Audio device: Intel Corporation N10/ICH 7 Family High Definition Audio Controller (rev 02) .....
I think the driver may be there, however I just can't 'enable' it. On my laptop there is a blue light saying that wifi is enabled however who knows.
I'm having trouble with my Samsung Netbook N220 and its Realtek 8192 wireless card and could use some help with diagnostics. I would like to use the netbook as a server and after a day or so the system stops responding. What I'd like to know:
- What do the "========>ieee80211_parse_info_param(): athros AP is exist" spam messages actually say? Does anyone else have this and stability problems?
- Why is the realtek driver package not working?
I'm running Ubuntu Netbook 10.04/Kernel 2.6.32-24-generic. Initially the card was unable to connect, so I installed the Realtek driver rtl8192se_linux_2.6.0017.0507.2010 which adds a kernel module r8192se_pci.ko. At first my system was hanging during bootup. I then restored /lib/modules/2.6.32-24-generic and now the card is connecting but the system is unstable. The 2.6.32-23-generic kernel, modules listed below, still has modules as installed by the realtek driver and is not working. Below the drivers supplied by ubuntu
./2.6.32-24-generic/kernel/ubuntu/rtl8192se/r8192se_pci.ko
./2.6.32-24-generic/kernel/drivers/staging/rtl8192su
./2.6.32-24-generic/kernel/drivers/staging/rtl8192su/r8192s_usb.ko
[code].....
Today I realized that my newly installed Natty does not recognize the Ethernet port, I used to have it when I was working on the Ubutnu 10.10. The following is the output (only the network related part) of lshw command:
Code:
-network
description: Ethernet interface
product: RTL8111/8168B PCI Express Gigabit Ethernet controller
vendor: Realtek Semiconductor Co., Ltd.
[code]...
I intend to attach WLAN PCMCIA card to my embedded system to connect to a wireless network. However, my embedded system uses a strangs OS that not supports the card driver. I think that I can investigate on how Ubuntu control the card to find out the way to control it in my system. The WLAN PCMCIA card that I can buy is:TP-Link TL-WN510G,Linksys WPC54GSCan any one tell me, how can I have the source code of WLAN PCMCIA driver and how can I find out the way Ubuntu control this card?
View 4 Replies View RelatedI have a Dell Latitude D800 with a Dell Wireless 1350 (802.11b/g) WLAN miniPCI Card. I need to install wireless on this laptop but I see no wireless card when I know I have the above wireless card. Here are some commands that I ran that I might prove useful:
[Code]....
Now, my issue is that I have no access to ethernet in my apartment so I need to rely on wifi for my install. But during the install when it is looking for the network hardware it never sees the TP-Link Dongle and never asks if I wan to load the firmware. I even tried it with the CD image that has the non-free drivers included but it never asks for the drivers. Any other distro, like Linux Mint 7.3, sees the dongle fine.
So is there a way to force load the realtek-firmware drivers during install?
I am trying to get the drivers and patches for my alfa AWUS036EW on BackTrack 5 with these instructions: [URL] Everything works until I type make I get this message:
[Code]....
I tried to install the latest RealTek driver for Linux and it has wiped all my devices. I've tried reinstalling the alsa-base packages but it hasn't worked
View 4 Replies View RelatedI patched my wireless driver in order to support packet injection. Using this tutorial:
- Install the Firmware:
Code:
- Create new directory:
Code:
- Now disconnect Internet and unload all your driver (use rmmod command)
- Move/copy the Compat-Wireless patched in /usr/src/drivers directory and unpack the drivers:
Code:
Blacklist the wl driver: (STA driver)
Code:
Currently I'm running Ubuntu 10.10, Kernel 2.5.35-29-generic. I have a Broadcom 4318 for my WLAN and a Broadcom 4401-B0 for my ethernet. I followed the tutorial and I managed to get packet injection working on my WLAN; however, my ethernet connection isn't working. I tried sudo modeprobe b44, but I get the following message:
FATAL: Error inserting b44 (/lib/modules/2.6.35-29-generic/kernel/drivers/net/b44.ko): Invalid argument