Fedora Networking :: HPLIP Port Settings - Printer Not Recognized
Aug 5, 2010
I have recently installed Fedora 13 on my netbook. I wish to use my HP Officejet via the HPLIP utility. The problem with this is that when I have the firewall turned on, the printer is not recognised at all during setup. When the firewall is switched off, the printer is recognised. The printer in question is an HP Officejet 8500a which is connected via Ethernet cable to a wireless router. I would like to know if there are any network ports (that's used by HPLIP) that I could 'turn on' in the firewall that could let my computer recognise the printer.
I have newly installed opensuse 11.4 x85_68 on my computer. Yast2 refuses to see my connected HP Laserjet 4l on parallel port, I can install a second network printer but neither hplip nor yast2 can start printer configuration. The printer is present in Yast2 hardware List under /dev/lp1
Deskjet-F4400-series -------------------- Type: Unknown Installed in HPLIP?: No, not using the hp: or hpfax: CUPS backend. Device URI: usb://HP/Deskjet%20F4400%20series?serial=CN9C1CK70705C5 PPD: /etc/cups/ppd/Deskjet-F4400-series.ppd
how do I get the printer installed in hplip? I can print but cannot scan. xsane will not recognize printer. Jaunty 64bit 2GB Ram 350GB HD
I installed a LPT1 printer a hp office jet T65 to add this printer was requested hplip I install the software that should de printer driver, when I print a file the file remain only in processing it wont go forwarder then that.I hope I was explicitly enough.
I did an upgrade using preupgrade program and it went very well. However, I have lost my HP 1020 printer. Can anyone assist with this. I tried to use HPLIP-Gui, but it doesn't even see the printer at all. The other problem is that I get the following message when trying to use Yumex:
Failure getting http://rpm.livna.org/fedora/11/i386/...ta/repomd.xml: 13:09:06 : --> [Errno 14] HTTP Error 404: Not Found 13:09:06 : Trying other mirror. 13:09:06 : Failure getting http://livna.cat.pdx.edu/fedora/11/i...ta/repomd.xml:
I have managed to install ubuntu server and set it quite nicely to share my files and printers over my network. I have two printers, a Lexmark e232 and a hp C3180 multifunctional printer (i.e. printer+scaner+a copy function). I have no problem installing the Lexmark printer on my windows 7 computers on the network, however, the All in One printer only gets recognized as a printer but there is no way to get it to scan. I have been reading on the web about all in one printers but I don't quite understand what the issues are.
Is there a way for me to get the full functionality of this printer over the network? I think this wouldn't be a problem if there was some sort of software designed by hp that would allow me to add printers that are not directly connected to the computer (via usb) but are shared from another pc on the network.
I recently had problems with my HP printer in Fedora 12, where as I never had a problem with it in any other distrubution.... For some reason, the HPLIP driver in the repo doesn't work correctly... I don't know why... but I kept getting errors with "error: Printer queue setup failed. Please restart CUPS and try again."
I tried every suggestion I found... which was installing extra dependencies, disabling firewall, disabling SELinux and a whole bunch of other stuff... but nothing worked... THEN finally I decided to use the HPLIP driver from the HP website... it was a .run file... and I executed it, and my printer has worked perfect eversince..... my question is.... has anybody successfully installed their hp printer from the hplip driver in the repo's..??? I don't know why it didn't work for me, and i've seen other fedora users complain of the same thing? maybe theres something wrong with the package? or its not pulling in a needed dependency? I don't know...
I have Ubuntu version 10.10 and I'm trying to install the HP DeskJet 1000 J110a printer. I have HPLIP version 3.11 (the latest version I believe). The printer shows up but when I try to print the error message reads: Printer requires the 'foomatic-rip-hplip' program but is not currently installed.
I have a desktop and a laptop connected by ssh (Places>Connect to Server). This works OK for file sharing but the laptop does not recognize the 2 printers attached to the desktop machine. As I understand (??) it, if the 2 printers are set up as 'shared' in CUPS (as they are on the desktop) then they should be recognized by the other machine on the network. But this is not happening. Is this the right way to network printers?
I am running 11.04 on a Dell Inspiron 1501 (the first gen.). I was using my Ethernet port to connect to the internet until about two weeks ago - suddenly the system no longer recognised that port even existed and just kicked me offline. I am able to get online now with a wireless card (replaced the broadcom card, that was a whole different can of worms...).
why my system is unable to connect with the Ethernet port? If I plug in the cable nothing happens.
A command like (single quotes used in the command):
Code: ssh -L '[::1]:3128:127.0.0.1:3128' ...
is getting an error message like:
channel_setup_fwd_listener: getaddrinfo(::1): Address family for hostname not supported
This is supposed to be an IP address, not a hostname, for the localhost in IPv6. Anyone know what is wrong with this? Addresses like this work OK in rsync. I know I can use ip6-localhost as a hostname. But right now I'm testing actual IP addresses in IPv6 to see what programs can or cannot handle it.
I have Ubuntu 9.04, and a HP laserjet 1018 printer.
I install the printer using:
And when it ask me about plugin I give the path to it. (the 3.9.2 version of the plugin, because Ubuntu 9.04 has the 3.9.2 version of hplip)
well I install the printer, everything works perfectly. .... but, when I turn off the PC, and turn it on again, the printer does NOT work!, I send work for being printed but mothing happens , Ubuntu tells me that the job was printed but ... no case, my printer does not print it. I have to install it again since cero. what can I don to stop install it every time I turn off the computer ?
Everytime I get HPLip working with my printer, it will only work until I shutdown the computer. On next restart, it no longer works and the only way to get it to work again is to delete the printer configs in hplip and re-create them!
Trouble with cups - Opensuse 11.3 x86-64 Hplip installed prrinter = HP photosmart 4280 No way I can set the printer as default printer in cups as in 11.2. Now hp-device-manager. Part of hplip is complaining "set the default printer"
I'm running Ubuntu 9.10. The Update Manager did an update to HPLIP, the Hewlett Packard Linux Internet Printing software, one or two days ago. When I went to print today, the HP Officejet 4500 printer showed up in Open Office when my mouse pointed to the printer icon. But, the printer wouldn't work. Then I noticed that the HPLIP Toolbox icon was moved from the Applications - Accessoires folder, to the System - Preferences folder. I reinstalled all the HPLIP software, using the Synaptic Package Manager. When I click on the HPLIP Toolbox & run the HP Device Manager, it says "No Installed HP Devices Found".I was a little surprised to see the software upgrade caused the HPLIP toolbox to move fromhe Applications folder to the System folder. Because of this, I suspect there may be a bug in the upgraded software? Is anyone else having this problem?
I just built a system and put a fresh install of ubuntu 9.10 on it. I have two other systems with 9.10 as well. On both of them the printer (an HP Officejet Pro 7680 set up directly on the network) is shown as an HPLIP printer with a URI that starts with hp:/net/ . When trying to set up this printer on the new machine the option for HPLIP is not present and the URI starts with dnssd://. I can only set up as and LPD Network Printer or an Appsocket/JetDirect network printer. Yes I have the hplip stuff installed on the new machine. My main concern is actually using the scanner function with Xsane. The other two machines scan just fine, the new one can't find any devices. I think this must be connected with the lack of HPLIP functions. This is with the AMD64 bit version of 9.10
I just installed HPLIP using Synaptic package manager. One of the configure parameters (shown by 'hp-check -r') is
Am I correct in assuming that this means that a network printer will not work? Is there a way to override this while still using synaptic package manager? Would I then be able to use a network printer?
I have my eye on the HP photosmart plus B209A - and it looks like HPLIP supports it (there is a ppd file for it).
I have an HP Photosmart USB printer that I configured with HPLIP (which seemingly "exports" into CUPS). All is well until the printer is turned off and then back on again sometime later: somebody, somewhere automagically adds the printer to CUPS so that I have two, count 'em, printers defined.
I want to do a simple port redirect, i.e. whatever comes trough whatever interface on port AAAA will get redirected to port BBBBI thought that iptables -t nat -I PREROUTING --source 0/0 --destination 0/0 -p tcp --dport AAAA -j REDIRECT --to-ports BBBBhowever it doesn't work, e.g. nc -v -w2 -z localhost AAAA gives:
nc: connect to localhost port AAAA (tcp) failed: Connection refused while nc -v -w2 -z localhost BBBB
while my brother was browsing the web on my windows partition he had a blue screen pop up, one of the soft/hardware error ones, not a true BSOD, anyways, ever since my lan port on the computer seems to not be activiating as no wired connection is recognized. The lan port/card is directly attached to the Mother Board, it's a gigabyte motherboard in a self-build computer. I'm just wondering if there's anything I can do to troubleshoot this and see if it is truly a hardware problem or if its something else.
after an update to 11.2 (from 11.1), 64 bit, I don't get the printer to work. I reinstalled the driver and checked in cups: it says that the printer is available and waiting for a job. When I send something to the printer, nothing happens. The priont job will be stopped immediately. The printer is properly connected: xsane finds the scanner, that is part of the printer, without a problem. The printer is also ok: I can copy documents, it just works fine.
I just installed opensuse 11.3 and was configuring the printer (via http) as usually using the HP Device Manager. But this time I got these error message:Printer queue setup failed. Please restart CUPS and try again
These lines were generated in the error-log of cups: E [31/Jul/2010:23:30:35 +0200] [cups-driverd] Bad driver information file "/usr/share/cups/drv/sample.drv"! E [31/Jul/2010:23:30:35 +0200] [cups-driverd] Skipping "/usr/share/ppd": loop detected!
So if I do dmesg | tail and find out that lp0: using parport0 (interrupt-driven). lp0: console ready [root@Juha Juha.Koskiniemi]# cat /proc/bus/usb/devices
What is it fro following? lspci 00:00.0 Host bridge: Intel Corporation 82855PM Processor to I/O Controller (rev 03) 00:01.0 PCI bridge: Intel Corporation 82855PM Processor to AGP Controller (rev 03) 00:1d.0 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #1 (rev 01) 00:1d.1 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #2 (rev 01) 00:1d.2 USB Controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) USB UHCI Controller #3 (rev 01) 00:1d.7 USB Controller: Intel Corporation 82801DB/DBM (ICH4/ICH4-M) USB2 EHCI Controller (rev 01) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 81) 00:1f.0 ISA bridge: Intel Corporation 82801DBM (ICH4-M) LPC Interface Bridge (rev 01) 00:1f.1 IDE interface: Intel Corporation 82801DBM (ICH4-M) IDE Controller (rev 01) 00:1f.3 SMBus: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) SMBus Controller (rev 01) 00:1f.5 Multimedia audio controller: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Audio Controller (rev 01) 00:1f.6 Modem: Intel Corporation 82801DB/DBL/DBM (ICH4/ICH4-L/ICH4-M) AC'97 Modem Controller (rev 01) 01:00.0 VGA compatible controller: ATI Technologies Inc Radeon Mobility M6 LY 02:00.0 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev aa) 02:00.1 CardBus bridge: Ricoh Co Ltd RL5c476 II (rev aa) 02:00.2 FireWire (IEEE 1394): Ricoh Co Ltd R5C552 IEEE 1394 Controller (rev 02) 02:01.0 Ethernet controller: Intel Corporation 82540EP Gigabit Ethernet Controller (Mobile) (rev 03) 02:02.0 Network controller: Intel Corporation PRO/Wireless 2915ABG [Calexico2] Network Connection (rev 05)
And how to evaluate the list of cat /proc/bus/usb/devices? I am asking this since seems that parport is recognized but why I can not access the it to via gtkteminal by using /dev/lp0 QGtkStyle cannot be used together with the GTK_Qt engine. Qt: Session management error: None of the authentication protocols specified are supported opening failed How to edit thread header since the misspelling?
Ive just installed Fed 13 KDE, but my Epson Stylus DX7450, is not recognized and installed. (works fine on Fed 13 Gnome). So i went to Printer Config. in system settings. New printer/ New network printer. where i get an error message "Not authorized - this password may be incorrect". I carry on and input my printer details, but at the end I get another error message, "There was an error during the CUPS operation: 'client-error-forbidden'."
I have ubuntu jaunty 9.04 installed in my system(thats my only OS.. no dual boot). When I tried to install hplip to enable hp printer driver, I understood that 9.04 is obsolete and no more support for it. I want to upgrade now. Update manager shows '10.04' for uogradation but it seems I cannot jump from 9.04 to 10.04 without getting into 9.10.
When I boot fc14 with an already defined printer connected on the parallel port, then I can use the printer. The printer appears on parallel:/dev/lp0. But, if the printer is not connected during startup, when I connect the printer I cannot use it. Nothing happens. I have no corresponding message using "dmesg" command when I connect the printer.
I cannot make cups see that the printer is connected, using "localhost:631" in firefox. Is it possible to "mount" the printer manually? Using "system-config-printer", the printer has to be "activated", even though it is not used or even connected. Then "parport" module is installed during boot (with other related modules: "ppdev" and "parport_pc").
Then, when the printer is connected, "dmesg" shows : lp0: using parport0 (interrupt-driven). lp0: console ready And, of course, it is now OK to use the printer.