Fedora Installation :: Grub Boot Loader For 2 Different HD
Jun 8, 2010
What I like is to install Fedora13,Win7,WinXp, and Musix. One HD 1.5TB Ilike on that is win7 and Fedora13,the other one with 400GB WinXP and Musix. What should I do so I can setup on GRUB. How can I set up like that.
I have XP, Win7 Pro and F 11 installed. Before I installed F 11, Win 7 boot mgr was working fine. I then installed F 11 and I went to System/Admin/bootloader to edit it and it wouldn't bring up the boot loader. In the attachment was the error msg. Now my only option when I boot up is F 11.
I do not have access to the Win 7 DVD only the F 11 install disk since I am on a fishing trip and need to use Win 7. How can I repair to the grub boot loader to boot into Win 7?
I successfully installed Fedora 11 from the DVD iso. At the end, the installation program prompts me to reboot the system. But when the boot loader appears after rebooting, there are only the old entries.
I have 2 IDE disks and one sata disk. The first IDE disk is hd0, the second IDE is hd1. The SATA disk is hd2. In the setup, I selected hd0 to install grub. Fedora 11 was installed on the SATA disk (hd2). I forgot to say, that Fedora 10 is on /dev/sda and Fedora 9 on /dev/sdb
I have an HP Pavilion m7480n PC with Windows XP installed on the C-drive. I successfully installed FC 12 onto the spare USB drive. When I rebooted the PC all I got was a blinking underscore at the extreme upper left position of a totally black screen. After a bit of experimenting I found that if I hit the F1 key during the boot process, go into the BIOS setup, do nothing within the setup, and press ESC to get out of the setup then the PC will go back into the boot cycle a second time. During the second time however a small text message appears with words to the effect "Press any key to enter GRUB..." after which the GRUB splash screen comes up with the choice for FC 12 or "Other" (referring to Win XP). At that point I can boot into either one.
I have a laptop with windows vista installed on the internal hardrive.Last March I installed wanted to start to use linux so I brought a separate external hardrive partitioned it to enable media storage on one section and installed ubuntu on the other half. It works fine and so does the windows vista on my internal hardrive, however I have to have the hardrive plugged in to boot.Until now this hasnt bothered me, however I've recently started to take my laptop into university and cannot switch it off unless I have the external hardrive with me as I cannot switch it on without it.With it plugged in it loads up GRUB and then gives me the option to load either Ubuntu or windows vista, however if it is not plugged in when I power up it says GRUB loader failed.It also occured to me that if for some reason my external hardrive fails in the future I wont be able to use my laptop anymore.Has the installation of ubuntu (and GRUB) altered the MBR? Is there some way I can edit the settings so that I can load windows vista without the hardrive plugged in, and then if it is plugged in I get the choice which one to load?
I had a dual boot machine with fedora 12 and windows vista and I could use grub boot-loader to switch between two. Few days ago windows got corrupt and I have to reinstall it. I put windows 7 now and as usual it erased grub. So to reinstall I put the fedora 12 installation CD on and followed some usual setup steps. When I got the command line I issued the command "grub-install /dev/sda" (sda not hda because It showed bunch of sda, sda1..) but surprisingly it said grub command not found. I remember doing it before while it worked fine.
I have installed Ubuntu 10.10 Minimal on a 2GB USB using CLI and it is working very well after I added a few things. I intend to use it on machines other than my own. But the GRUB boot loader was installed to the main system on my machine and it is booting from there.
During the installation it was said that the bootloader can be installed on a floppy. So I started a new 2 GB stick and tried to install the boot loader on a floppy but my computer does not recognize floppies anymore (seems to be a wider problem with recent distributions).
So I tried to install the bootloader on a different USB stick and and this also did not work. Cannot find recent and relatively easy way to install GRUB boot loader to a stick.
I installed Ubuntu 11.04 64-Bit via Wubi but it seems that when I turn on my machine I first get the Windows Boot Loader, when I select Ubuntu from the list it then goes into GRUB with the option to select Ubuntu or Windows. Is there any way to change this so only GRUB is used?
I got the grub loader to work finally. The problem is it does not always display at initial boot or a restart. I have seen the selection menu but it doesn't always appear. I have it set to point to windows so that my wife can hit enter when she gets a blank screen.
As I attempted to uninstall an MP3 decoder through the command line, I may have also uninstalled the boot loader to Fedora 13. I entered the command to uninstall the program as su - , left for a second, and upon my return I noticed a lot of things were being uninstalled. After canceling the process I turned of my computer and now when I try to start it, my computer freezes after the Fedora icon appears on the blue screen. After looking through the online manuals, I think I uninstalled the GRUB boot loader. I've been trying to reinstall it through the image on the DVD, but it keeps getting stuck on the blue screen. I use a Toshiba satellite with no partitions.
I've had to give up trying to install linux. It just won't work on my machine, a Presario 6370us that has been upgraded over the years such that it is not compatible with linux, apparently. (You can read my travails elsewhere on this board; thanks very much to all who tried to help.)
Now, how do I remove the GRUB boot loader from my system? I need the system to boot directly to Windows XP.
I can't start linux in any way, shape, or form, so I need to either edit GRUB inside the GRUB environment itself, or to do so from Windows.
Ideally, I'd like to remove GRUB entirely. Failing that, I'd like to edit the GRUB config file so that only Windows is an option. Failing that, I need to make Windows the default OS.
i installed it on a external HDD. my primary OS is windows 7 on my 1 internal hard drive. After i installed ubuntu whenever i boot up my computer i have to have my external hdd plugged in and turned on or else i get "cannot find GRUB" then some rescue thing comes up where i can type stuff. i would just like to move the GRUB loader to my primary hard drive or at least recover my windows loader but have ubuntu on it.
I have installed Linux mint and it failed on grub, if I press something grub crash, tired of that I install Ubuntu but my surprise was the same problem on grub, I was thinking if grub2 was the problem, so I tried grub legacy and was the same x_x
I remember use a old version of ubuntu with lilo (or was opensuse) but it works! but neither last ubunt nor mint with grub
Grub loader: select OS If I press ANY key it crash, if I wait the 9 seconds it enter to default OS (first option)
Note: It is neither PS2 nor USB keyboard, it's a laptop keyboard, a Compaq presario 2100
I tried to install linux on hard disk and it installed without any problem. However, when i boot i directly get the windows boot loader screen and no grub screen. I reinstalled linux. I tried to fix grub, but still no grub screen.
I installed Ubuntu 11.04 on a separate partition, with Grub being in it own partition. When I start the PC only windows Xp is available. So how do I get grub or Ubuntu load with windows xp boot loader? I tried with Live cd, the sudo grub but then it says command not found. I think its because Ubuntu 11.04 uses grub 2.
I just installed Fedora 11 (I installed over the Fedora 10 installation I had already installed)..
-Before I would have Grub give the choice of Fedora 10 or Windows (Where Windows would load the Win Boot loader for my options of Windows 7 and Windows Vista)
-NOW: I have the same options.. But when i select Windows (It loads the Recovery partition) instead of the Windows Boot Loader...
Here is my fdisk -l
Device Boot Start End Blocks Id System /dev/sda1 1 192 1536000 27 Unknown Partition 1 does not end on cylinder boundary. /dev/sda2 192 5414 41943040 7 HPFS/NTFS Partition 2 does not end on cylinder boundary. code....
I'm having a problem installing Ubuntu Studio 9.10-alternate-amd64 onto my machine. This is the third attempt and I keep running into the same problem. Grub Boot Loader will only install to 16% when a screen pops up:
Ubuntu Installer Main Menu
Choose the next step in the install process:
choose language configure the keyboard detect and mount CD-rom etc...
choosing the option "Install Grub boot loader on a hard disk" sends me back to the Grub install and once again at 16% the Ubuntu Installer Main Menu pops up. Choosing the option "Install the Lilo Boot Loader on a hard disk" resolves in an Lilo-install failure and i'm directed back to the Installer Main Menu. The option "Finish the installation" sends me back to the same menu..I'm stumped as to what to do... a disk check ensured me that the instal-dvd is valid though I can't get past this silly install menu.
I have Windows 7 and Ubuntu 10.04 dual-booted on my machine. grub was aautomaticlu installed as the primary loader. Soon i want to nuke my ubuntu partition but i know that will delete grub. Can i remove grub or at least make Windows boot loader default.
I am a brand new Ubuntu user that just tried to install on an old PC using the 10.10 desktop edition.During installation, I hit an error that the bootloader could not install, and after reading about it on the forums, opted to attempt to install it manually after. I have followed the tutorial located here,[URL].. on reinstalling GRUB2 from the liveCD, which I assume means to boot with the installation CD and select try Ubuntu (given the only other option is install, which I have tried twice) everything up to step 5 in that tutorial seems to run successfully, and I am given a message it is installed, but then when I reboot the system it does not open the GRUB2 menu, rather the CLI interface, which suggests there is no grub.cfg
So I am unable to refresh at the GRUB menu because that command is not recognized by the CLI (and it may not help if I am missing files, so I might have screwed up reinstalling them in step 5, or maybe the "Try Ubuntu" terminal doesn't alter the computer like I thought?)
I am a new Ubuntu user, and I am attempting to set Windows 7 64 bit as my default OS in the boot loader instead of Ubuntu 10.10. I have entered the command gksudo gedit /boot/grub/menu.lst into terminal, and the menu.lst file does open. However, this file appears to be completely blank, which does not seem to make sense and is preventing me from changing the boot order.
Not a major issue but my Ubuntu boot screen change to the old classic Orange theme after i installed Kubuntu on a different drive and ofcourse a new Grub loader as the Kubuntu installation prompted. It can't be because of the Kubuntu installation but i can't find any other reason for that to happen.
I recently replaced a failed graphics card w/ a GT 240. Next thing I know, Fedora 11 won't boot up properly. I guess it was a driver issue. I can tell you I went about fixing it all wrong because I wiped the FC11 partition (intending to install FC13) and now I can't boot anything up. My system consists of: sda1 vista, sdb1 XP, sdb5 extended, sdb6 Fedora. I thought grub was on the fedora partition, but reinstalling fedora with grub on that partition didn't fix the boot up problem. Do I need to replace the windows boot loader on sda1 with grub when installing fedora?
I installed Fedora 14 alongside windows, overwriting my old Ubuntu 10 partition. Unfortunately, now the GRUB loader only recognizes my Fedora partition and the built-in windows recovery utility partition. I checked the disc utility and my windows partition still definitely exists, I just can't seem to boot into it.
A failed upgrade, from disk images, of Fedora 10 to 11 resulted in no GRUB bootloader main menu appearing on bootup (no WIN, no LINUX choices from which to boot). I am booted directly into the GRUB command shell...so, no WIN, no LINUX, nothing. And my understanding of GRUB shell commands is very low.I have 2 hard disks, WIN on the first, LINUX on the second. I believe GRUB Bootloader is on the first disk.Sadly, I have no external install media.An old grub.conf hardcopy indicates that root =/dev/sdb2, root (hd1,0), kernel /vmlinuz....olderversion...(relative to /boot),initrd /initrd...olderversion... (relative to boot). and WINDOWS on (hd0,1), with chainloader +1
I need to somehow get past this grub shell, and re-install/re-instate the grub bootloader, so it can boot normally.What grub command(s) must I use? I've played around with the commands, but with no success.I worry that if I can't resolve this, the whole machine may be useless.