I just installed Squeeze on an older PC. Installation seemed to go fine. But when it booted up on the installed system for the first time, I could not login - username/password failure. I tried every possible typing error and CAP LOCK error I could have made - still nothing.
I brought up a console window and tried logging in as root - same problem.
I booted into single user mode and entered passwd command to set new root password - I got a SYSTEM ERROR message from the passwd command.
I booted to a Live CD, went to /etc/shadow and deleted the encrypted password. Rebooted on the hard drive, went to console window and logged in as root, with no password required. So far so good. I entered passwd command to set new password and got the same SYSTEM ERROR message.
The machine seems fine when running on the Live CD, and the install seemed to go fine.
I am using rhel5 with ip 192.168.0.254.i am using rhel on vmware 7. when i run links 192.168.0.254 then i got error "bash : links : command not found" i want to know why this error is showing? when i use red hat without vmware then there is no problem.
I did install a brand new debian etch on my server, update and upgrade has been done.I did installed a postfix and couple of tools ( like courier-* ).But when i want to try to sent a mail with mail command, it says command not found.I did use the method on the bottom of this thread succesfully, but any idea for this tool to be back on my server ?Did i uninstall it when installing a package ?
I'm trying to boot into the Live CD (64bit version) and it dies with an error "nouveau .... 0x8DF6 Init table command not found: 0xA9". Get the same error after I install and try to boot into Debian, it starts booting but errors out later.
Running Intel 4770K on Gigabyte Z97X-UD5H with 8G ram, Nvidia graphics card and several SSDs ...
I downloaded linphone 3.30 using mozila and tried installing. while giving the command ./configure it was successful and next giving the command make gives me a error message make file is not found. but makefile.am and makefile.in is already available in the current working directory.
I have given the link of the pastebin for ./configure command and make command..
I was running an update on my computer (running Ubuntu 10.04 Lucid) and something must have been transferred incorrectly as every time I open synaptic, I get an error message that tells me to type a command into the terminal:
Code: sudo dpkg --configure -a After doing that, it displays this:
I've installed openMPI-1.4.1 on my laptop and I'm trying to compile some fortran code I've written using MPI. I downloaded the openMPI-1.4.1 file from the openMPI website and used the shell script they provide to install it. This is the shell script:
shell$ cd openmpi-1.4.1 shell$ ./configure --prefix=/usr/local shell$ make all install
There was an additional line extracting the tar file, but I did this by hand. The first time I ran this script there was an error on the final stage saying that a directory couldn't be created because of lack of permission. I decided to run the script again this time as a sudo.
Having run the script again everything appeared to install properly, however when I went to compile some fairly simple code I got a message saying that the compiler couldn't find MPI. I was using this command: gfortran messages.f90 -o messages I looked on the openMPI website where it recommends compiling with a compiler called mpif. However when I type mpif messages.f90 -o messages I get an error message saying mpif isn't a recognized command......
I am having problems installing fortran g95 compiler. I followed the exact instructions listed on the website The G95 Project (click on manual tab for further details), but I am still getting this error when I try using the driver:
shamo@linux-wrws:~> g95 bash: g95: command not found
Here is what I did:
>wget -O - http://ftp.g95.org/g95-x86-linux.tgz | tar xvfz -
The program installed properly, and I was able to verify the installation in /usr/share/g95-install. All the libraries were installed, and I was able to run the actual "executable" when I cd'ed to its directory) Next I created a symbolic link to the driver so that I could run from anywhere using g95 command:
I was reading in one of my redhat books that this command would make linux rered the inittab file but whin I try it I get Bash: init: command not found.
i try today to install Firestarter , unfortunately i got some problems regarding of the following messages:
1- insufficient privileges : 2- how can i change and save the file /etc/sbin/firestarter with visudo cammand 3-i got this message when i try to run it through terminal Error reading /proc/net/ip_conntrack: No such file or directory
I am having redhat 5 linux machine running on my windwos x in vmware workstation. Today i was installing oracle software in redhat 5 after editing the bash profile for the oracle user i got the following messages
su - oracle password:***** -bash: [oracle: command not found
i am using scientific linux, fedora 12accidentaly i changed LD_LIBRARY_PATH of the root profile to a different location. so terminal cannot understand any command as i type. is there any other ways to access .bashrc file exept using editors emacs, vi, nedit. my own profile works fine but i dont have permission to access the root folder. only commands the terminal responds to are pwd, cd, echo. i dont have any clue how to restore the library because it locates here:
I'm not entirely sure how to describe this. I've got a user account set up and I've downloaded a few programs I'd like to install. When I'm in my account, I go to the terminal and type then get; $ pkgtool bash: pkgtool: command not found However, if I'm in root and do the same thing, it brings up the menu. What do I have to do to get pkgtool to work from my user account?
Gcc seems to be installed by not configured maybe?Below are some command line resultsIs gcc installed, and if so, how do I configure it so it run properly.
