I have a netgear wg111t that is running with ndiswrapper. It has an atheros chipset, but calling it ath0 didn't work.
Heres /etc/network/interface :
# This file describes the network interfaces available on your system
# and how to activate them. For more information, see interfaces(5).
# The loopback network interface auto lo
iface lo inet loopback
I had one of those random system deaths, so reinstalled squeeze (daily netinst image I think...) on my eee 1000, which uses an rt2860 wireless chip. The new install only installed 2.6.32, which I had been avoiding using because of a few problems, including it dealing with networking slightly differently. I couldn't get it to work - even without encryption - using wicd. Having had a read of [URL]... , I had a look at /etc/network/interfaces, which read; This file describes the network interfaces available on your system and how to activate them. For more information, see interfaces(5).
[code]...
ra0 is now called wlan0, as far as I'm aware. I've read in several places that it is best to expunge this file of all references to wifi, so I removed the bottom section (after '# The primary network interface'). I still got nothing. However, if I go ahead and change the 'ra0's to 'wlan0's, it seems to work - wicd connects. Not very familiar with Debian (spent more time on SUSE. Drop your tomatoes - I like it. Any idea what is happening? Is what I'm doing wrong? Conversely, is the file wrong? Should it be reported? Against which package? Including any particular files?
I have a rather urgent problem with my network, I got two virtual network interfaces one internal and one external. The problem is; I can't get connection to internet. The external NIC is set as a NAT and the internal is... internal.
/etc/network/interfaces
auto eth1
iface eth1 inet static
address 192.168.1.200
netmask 255.255.255.0
Running with this configuration makes my internet connect go away, however if I remove the configuration for eth1 everything is working fine.
I was just wondering if there's any point having both auto and allow-hotplug against the same interface in network/interfaces as allow-hotplug seems to bring an interface up at boot on its own.
View 3 Replies View RelatedI have a Dell PowerEdge SC430, Squeeze 6.0.2 box, Broadcom NetXtreme NIC which works fine DHCP. The network-manager package is not installed. I have now reconfigured /etc/network/interfaces for a static IP:
auto eth0
iface eth0 inet static
address 192.168.1.2
[code]....
What is the maximum number of virtual network interfaces possible?I would like to create around 300 or so. This is needed to simulate a 300 node network.
View 6 Replies View RelatedAlright, every time I boot or shutdown my routing box, it hangs at configuring and deconfiguring network interfaces. Below is my interfaces file. I see no errors or warnings in my log and I am running a pure kernel, not tainted with proprietary drivers. All of my hardware is 100% supported.
[code]...
As above, my wheezy 32bit hangs at boot. the last few lines displayed are
Code: Select allMounting local filesystems...done.
Activating swapfile swap...done.
Cleaning up temporary files...
Setting kernel variables ...done.
Setting up resolvconf...done.
Configuring network interfaces...
[Code] ....
I removed the files from /etc/network/interfaces.d/ just in case. i still can't boot up.
Resolved (I think) as on this post: [URL] ....
i recently started sockets programming. In the process i began to look for relevant network information about my computer and realized that ifconfig wasn't displaying the same information that resides in my /etc/network/interfaces file. On the interfaces file my IP address is 192.168.1.109 for interface eth0 but ifconfig displays 192.168.1.101. I was under the impression that ifconfig got its information from the interfaces file but clearly doesn't. I tried re configuring the device with ifconfig and then disabling and re enabling the device with ifdown and ifup so that the device updated its information but it didn't.
[Code]....
I bought a USB wireless adapter for my desktop. I finally got it to partially work using firmware-ralink as described [URL]sing network manager it will pick up my wireless network. However it will not connect to it.
The output of iwconfig is
wlan0 IEEE 802.11bg ESSID:"familyfarm"
Mode:Managed Frequency:2.437 GHz Access Point: 00:1C:DF:B6:EA:B9
[code]...
I use a 'wifi hotspot' provided by my mobile (android) phone for internet/email and to connect to my wifi capable HP p1102w printer. Installation and use of the printer worked perfectly until I bought a new phone, again android with 'wifi hotspot' capability. The wifi connection on my new phone works fine for internet and email but it totally fails to detect my printer.
I have tried to detect and connect to the printer using system-config-printer and using the HP utility hp-setup. Both fail to detect the printer on the 'new' wifi network.
The old network connection which detects the printer as expected gives the following output:
Code: Select allpat@debian:~$ ifconfig
eth0   Link encap:Ethernet HWaddr 6c:3b:e5:91:ec:0cÂ
     UP BROADCAST MULTICAST MTU:1500 Metric:1
     RX packets:0 errors:0 dropped:0 overruns:0 frame:0
     TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
     collisions:0 txqueuelen:1000
     RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[Code] ....
The new (problematic) network connection which fails to detect the printer gives the following output:
Code: Select allpat@debian:~$ ifconfig
eth0   Link encap:Ethernet HWaddr 6c:3b:e5:91:ec:0cÂ
     UP BROADCAST MULTICAST MTU:1500 Metric:1
     RX packets:0 errors:0 dropped:0 overruns:0 frame:0
     TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
     collisions:0 txqueuelen:1000
     RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[Code] ....
I'm installing Squeeze on on a Dell Latitude D830 laptop with a Broadcom BCM4328 wireless network card, and I'm stuck on getting wireless internet to work. I have the 2.6.32-trunk-686-bigmem kernel. I run KDE and I have knetworkmanager installed to sort the network connections out. Unfortunately, knetworkmanager cannot find any wireless networks for eth2 (the wireless adapter). There is a wireless network, as other equipment can still connect to it.
I've installed the broadcom-sta drivers according to http://wiki.debian.org/wl. When I run iwconfig, I receive the following output: eth2 IEEEE 802.11abgn ESSID:"" Mode:Managed Frequency: 2.412 GHz Access Point: Not-Associated Bit Rate: 14 Mb/s Tx-Power:off Retry min limit: 7 RTS thr:off Fragment thr:off Power ManagementMode: All packages received Link Quality=5/5 Signal level=0 dBm Noise Level=0 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 missed beacon:0
[Code]...
I have Debian 8.2 with KDE 4.14 and everything runs perfect, except for the internet connection. This problem happens randomly when I turn on my machine. Sometimes when the desktop loads, the connection is already settled.
But sometimes when the desktop loads, the wifi icon is still loading and keeps stuck at "setting network address". Since this problem happens randomly I really don't know what is happening here. My wifi chip is this:
Code: Select all01:00.0 Network controller: Intel Corporation Centrino Wireless-N 130 (rev 34)
This is the problem:
I installed Debian with non-free firmware because of this chip.
I got this message when I tried to get in WifiSettings.
"The system network services are not compatible with this version"
What should I do?
I have a weird problem with my /etc/network/interfaces configuration. I have the most simple static setup possible: Code: # cat /etc/network/interfaces
auto lo
iface lo inet loopback
auto eth0
[code]....
Similar to the linux command "chattr +i filename", I would sure like to set my eth0 interface immutable. so once I assign the eth0 interface's IP and gateway, make it stay set until I say otherwise.
this way, I can run dhclient or Networkmanager on another interface without having to fret that it may alter this interface. is there something out there that can do this?
I have a laptop connected to internet via wlan0. I also have eth0 interface and with it I share internet. I want to modify/filter all the traffic passing by the first laptop, something like this:
Code: Select all          *---------------------------*
          |    LAPTOP 1      |   *--------------* ?
          |-----*  *------*  *----*   |       |
  INTERNET<------>|wlan0|<-->|MY_APP|<-->|eth0|<---->|ANOTHER LAPTOP|
          |-----*  *------*  *----|   |       |
          *---------------------------*   *--------------*
I know that in FreeBSD it is possible to use ipfw for that purpose, because it build-in into kernel. We set for example rule Code: Select allipfw add divert 2000 ip from any to 1.0.1.1
and we can use our own application to process those packets, reinject them forward etc. It will work also fast, because as I said, it build into kernel.
Is there any standart Linux-based solution to do the same? I found some info about netmap-ipfw. Is this a correct solution? Or I have to use for example IP-aliases and iptables to do that?
I need to process all the IP-packets, not only TCP/UDP/etc-protocol. Solution also must be very fast.
My new Squeeze machine detects all of my hardware including the LAN and WLAN cards, but only brings up the LAN card. There isn't even an entry for it in /etc/network/interfaces for me to modify. I tried adding the info manually but then the entire network wouldn't start. I had it configured as a static IP and I know the commands were correct due to them working on the LAN card. I believe that the name "wlan0" was causing the problem, but how else can I bring it up at boot?
View 7 Replies View RelatedIf I try to add a new interface (eth1) to /etc/network/interfaces, I get
Code:
* Reconfiguring network interfaces... SIOCSIFADDR: No such device
eth1: ERROR while getting interface flags: No such device
SIOCSIFNETMASK: No such device
[Code]...
How do I add 2 interfaces and get anyone of them to work, as available ?
So I've always asked this in the past when I get on a Debian system. This makes no sense to me but I just don't see how I restart network interfaces (i.e. eth0) on a standard Debian install. If I change the static I.P. address listed in /etc/network/interfaces from x.x.x.100 to x.x.x.101, I then assume I can simply do any of the following:
- /etc/init.d/networking stop | start
- ifdown eth0
- ifup eth0
- service networking stop
- service networking start
All the commands above do nothing. My only solution I know that works and implements the changes I've made is a complete system reboot which to me in Linux, is ridiculous. I've struggled with this over and over and nothing I do correctly assigns the new I.P. in the 'interfaces' file to the actual adapter. This isn't my single isolated Debian machine but every Debian machine I can get my hands on. Servers, workstations, VM's, any release, etc etc etc. Below is my interfaces configuration file:
Code:
auto lo
iface lo inet loopback
[code]...
How do Linux identify the eth0, eth1, eth2 interfaces. For instance I plug in a network cable in to an interface. How do Linux recognize the plug in interface is eth0 or eth1?
View 1 Replies View Related I should be able to access xfinitywifi hotspots. /etc/network/interfaces and /etc/wpa_supplicant.conf. I don't want to use NetworkManager for this connection.> iw dev wlan0 scan
BSS 60:02:92:e6:78:0a(on wlan0)
TSF: 1619575398784 usec (18d, 17:52:55)
freq: 2437
beacon interval: 100 TUs
capability: ESS ShortPreamble ShortSlotTime (0x0421)
signal: -65.00 dBm
[code]...
I had some trouble with the netinst CD and I had to install lenny with the 6DVDs instead. My internet connection only works after I edit the interfaces and resolv.conf files manually. So my question is: can I do that from the netinst CD before it actually needs the connection to install everything? (otherwise I'll just need to use the DVDs.
View 4 Replies View RelatedMy pc is aser aspire 5735z. I have acer nplify 802.11b/g draft-n wlan
but i can use wifi on debian
what i have to do ?
Do i need driver or firmware?
how can i solve this problem ?
I did a netinstall earlier today (latest version, amd64) on my Dell XPS laptop and ended up with a minimal installation because I couldn't connect to the internet. Now I'm trying to get online without a desktop environment.
I have an Intel Centrino 1030, so I downloaded and installed the firmware [URL].... with a usb, then rebooted. My searches have turned up a lot of instructions involving a utility called iwconfig and wpasuppliant, but these are apparently not installed. I don't really know much about it, but my /etc/network/interfaces file looks rather empty:
Code: Select all# The loopback interface
 auto lo
 iface lo inet loopback
Shouldn't there be something like wlan0 there? The network card does show up with lspci
I've been installing multiple versions of ubunutu over years and now I better understand why I faced always problems with wifi configuration on these different baselines : Debian root of course.
Now on Debian 7.4 :
The Broadcom BCM4313 driver is not loaded by default (not free product) for my wifi card. This is stated thru the UNCLAIMED declaration
Code: Select allÂ
sudo lshw -c network
 *-network UNCLAIMED
    description: Network controller
    product: BCM4313 802.11b/g/n Wireless LAN Controller
    vendor: Broadcom Corporation
    physical id: 0
[Code] ...
Unclaimed means : no driver found (no kernel association)
So I installed the driver located in the non-free backports by adding this target into the repository
Code: Select alldeb http://http.debian.net/debian/ wheezy main contrib non-free
and install :
Code: Select allsudo apt-get update && apt-get install firmware-brcm80211
sudo modprobe brcm80211
Check seems OK :
Code: Select allsudo lshw -c network
 *-network
    description: Wireless interface
    product: BCM4313 802.11b/g/n Wireless LAN Controller
    vendor: Broadcom Corporation
    physical id: 0
[Code] ....
I can't connect with wlan0, it doesn't work. I found information here regarding WPA2/PSK wifi configuration on debian : [URL] ....
so I added this setup to my interfaces file an got :
Code: Select allauto lo
iface lo inet loopback
allow-hotplug wlan0
iface wlan0 inet dhcp
 wpa-ssid Hznteam-Datacenter
 # hexadecimal psk is encoded from a plaintext passphrase
 wpa-psk 12345678901234567890123456
It's worth ! no more wifi network are detected and ifconfig gives no ip address allocated :
Code: Select allwlan0   Link encap:Ethernet HWaddr 78:e4:00:4e:49:a3Â
     UP BROADCAST MULTICAST MTU:1500 Metric:1
     RX packets:0 errors:0 dropped:0 overruns:0 frame:0
     TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
     collisions:0 txqueuelen:1000
     RX bytes:0 (0.0 B) TX bytes:0 (0.0 B)
[Code] ....
In a hp pavilion 15 Notebook PC with Debian 8.1.After two hours or so wifi stops working. Network-manager does not give any indication of failure but some times a yellow question mark.
rfkill list wifi gives:
0: phy0: Wireless LAN
Soft blocked: no
Hard blocked: no
ifconfig gives:
eth0 Link encap:Ethernet HWaddr 8c:dc:d4:7b:c2:0e
UP BROADCAST MULTICAST MTU:1500 Metric:1
RX packets:3994 errors:0 dropped:0 overruns:0 frame:0
TX packets:3661 errors:0 dropped:0 overruns:0 carrier:0
[code]...
I've installed Debian 8.1 on Lenovo G50-80 Touch. Ethernet is OK but the WiFi adapter is disabled. How can I enable it?
Code: Select alluname -a
Linux debianserv 3.16.0-4-amd64 #1 SMP Debian 3.16.7-ckt11-1+deb8u3 (2015-08-04) x86_64 GNU/Linux[code][/code]
[code]lspci -nnk | grep -i net -A2
02:00.0 Ethernet controller [0200]: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller [10ec:8168] (rev 10)
  Subsystem: Lenovo Device [17aa:3821]
  Kernel driver in use: r8169
03:00.0 Network controller [0280]: Qualcomm Atheros Device [168c:0041] (rev 20)
  Subsystem: Lenovo Device [17aa:3545]
I am new to linux and decided to use Debian. I installed it on my laptop and have a few problems.First one is my WIFI.
Laptop type: HP Omen 15
Wifi adapter: Intel Wireless 7260n
rfkill list output:0: hci0: Bluetooth
Soft blocked: yes
Hard blocked: no
So wifi is not displaying
Kernel: 3.16.0-4-amd64
Debian version: 8.4
gui: LXDE
URL....
But they see in rfkill list the adapter.How to make this adapter work?I did this with no result:
nano /etc/modprobe.d/blacklist.conf
in file add:
#Fixing a bug that prevents wifi from working on HP Omen
blacklist acer_wmi
I would like to learn more about Linux, but before experimenting I need a working system. The plan for me is to run this as my native machine with vms on top of it with other OS.
I have finally weaned my laptop from network manager by setting up my /etc/network/interfaces file. # The loopback network interface auto lo iface lo inet loopback
# The primary network interface allow-hotplug eth0iface eth0 inet dhcp
# Wireless Setup auto wlan0 iface wlan0 inet dhcp wireless-essid linksysn
wireless automatically connects to my home wireless network (linksysn). But suppose I wanted to take this laptop to the coffee house where they have free wifi. I am assuming that my wireless will not automatically connect to any other wifi hotspot except linksysn. So how do i set it up to roam like NM did?