Debian Configuration :: Wheezy - After Update Systemd Turn Off Laptop Screen On Boot

Sep 25, 2015

I decided to update all the software on my computer. Fortunately, it upgraded kernel version 3.14 to 3.16. I was happy to learn that suspend now worked on my laptop by calling pm-suspend, but it did not worked by closing the lid. So I search and found on debian's website that installing systemd and adding some config lines in /etc/systemd/logind.conf would sove the issue. So I followed the procedure and did like instructed, to end up with a computer that boots on black screen.

The last verbrose line I see on boot up is "kvm disabled by bios" and then it shutdown down the screen. The computer works, as I can login and shutdown by doing those operation blindly.

I tried removing systemd but it still does not work. If I use the old kernel 3.14 I can boot without any problem, but if I use kernel 3.16, I boot to a black screen. I remember successfully booting in 3.16 before installing systemd.

View 4 Replies


ADVERTISEMENT

Debian Configuration :: Systemd Boot Is Now Verbose

Aug 13, 2015

When I first started running Jessie 8.1 I noticed that after the disk check the boot was quiet, ie. no messages to the terminal . However, something has happened and now when I boot the machine I get a verbose listing of all the processes being started. Is there a way to change it back to the way it was? In other words a quiet boot. The only thing I know of that has been 'anomalous' behavior is the other day when doing a mp4 to avi conversion, using avconv, I apparently had an over temp condition which closed my LXDE session and brought me to the login prompt. Don't know what other info one may need but feel free to ask for more, if necessary.

View 13 Replies View Related

Debian Installation :: Multiple SystemD Errors After Upgrade From Wheezy

Mar 3, 2016

Recently I upgraded my machine from wheezy to jessie.

Everything went smooth until the point that I restarted the node.

During startup I'm getting the following message which is flooding the screen:

Code: Select allsystemd-journald[296]: Failed to forward syslog message: Connection refused

After waiting a long time (the message above still continues to flood the screen), I'm being prompted with the following:

Code: Select allGive root password for maintenance (or type Control-D to continue):

If I press Ctrl+D the boot process continues and finally boots normally.

What I can do to avoid pressing Ctrl+D during the boot process?

I'm assuming that it must be a startup service which is failing but I'm unable to trace which exactly is that.

I'm attaching the full log [URL] ....

View 8 Replies View Related

Debian Configuration :: Systemd Can't Read Boot Logs Of Failed Boots

Mar 25, 2016

I'm getting BSOD when I'm booting my main system (debian 8 fully updated). I get a BSOD with a _ sign. URL...because I can't access to failed boots files. Besides having the files

Code: Select allfelipe@debian ~ % ls /var/log/journal   
362d07f9e18b45f8aec4575c347f181d  92e8a448f7a348719da129184a7e6821

Code: Select allfelipe@debian ~ % journalctl --list-boots
 0 0c51ae5b67f144059c5470dbe345d621 vie 2016-03-25 09:05:29 ART—vie 2016-03-25 09:11:58 ART

View 3 Replies View Related

Debian Installation :: Dist-upgrade From Wheezy (using Systemd) To Jessie Hangs

Nov 19, 2014

I have done on previous releases, but this time it hangs on me. It's "only" a Virtualbox, so I can reproduce it.

The wheezy already runs systemd, and is fully updated to to latest packages. Does not run any graphical.

Edits the source.list and does
$ apt-get update
$ apt-get upgrade # Did on one upgrade
$ apt-get dist-upgrade

It starts to upgrade (complains about missing version in libpgp-error), libc is installed, but at some point the systemd is running at high CPU and a dpkg seems to be stalled.

Should I disable systemd on wheezy before? This might not have been tested so much.

View 10 Replies View Related

Debian Configuration :: Use A Key To Turn Off Display On Laptop?

Sep 17, 2010

I am wondering if it is possible turn off my display with a key of my laptop's keyboard. I mean if I press ctrl + o then my display turn off and then if I press ctrl + o my display turn on.

View 5 Replies View Related

General :: Turn Laptop On And The Comp Prepares 2 Boot The OS,a Screen Asking To Choose Which OS Version?

Apr 7, 2011

i've got UBUNTU 10.10 installed on my laptop.After i turn my laptop on and the comp prepares 2 boot the OS,a screen asking me to choose which OS version i'd like 2 select.Now ideally i'd like jst 2 names on dat list namely-Ubuntu and win xp..But I've a host of other options as well like memory testblahblah'safemode'....wotevr....Is this ok 2 have so many OS startup options.Is there a way to get rid of unwanted stuff like changin the BOOT.ini file or in any other way???

View 11 Replies View Related

Debian :: Unable To Boot After Latest Update Of Wheezy Amd64

Jun 21, 2015

After the latest update of Debian Wheezy, about three days ago, one of my machines won't boot anymore. The update was done by:

Code: Select all/usr/sbin/update-smart-drivedb
apt-get update
apt-get -y upgrade
apt-get -y autoremove

I get the error message: "Alert! /dev/disk/by-uuid/71c... does not exist. Dropping to a shell!"

The dir /dev/disk contains only "by-id" and "by-path".

I booted with the rescue system, dropped into a shell and recreated the ramdisk with

Code: Select alldpkg-reconfigure linux-image-3.2.0-4-amd64
dpkg-reconfigure grub-pc

But without success. On another machine the update went flawlessly.

View 7 Replies View Related

Debian Configuration :: While Watching YouTube Makes Screen Turn Off

Jul 1, 2015

When I watch any video on YouTube my screen will turn off (no HDMI connection) and then it will turn on after a couple seconds (10 -40 seconds). When I played Borderlands 2 the screen is completely fine.

View 10 Replies View Related

Debian Configuration :: Systemd Custom Service

Aug 4, 2015

On macbook air 6.2, i've installed a Debian jessie mate DE, dual boot using refind. I'm currently fine-tuning it. I've made a script following powertop advice:

Code: Select all[newb@debian /etc/systemd/system]$ cat mba_kb_sp.sh
#!/bin/sh
echo 'auto' > '/sys/bus/usb/devices/1-3.1/power/control';
echo 'auto' > '/sys/bus/usb/devices/1-3.2/power/control';
echo 'auto' > '/sys/bus/usb/devices/1-5/power/control';
exit 0

[Code] ....

All seems to work fine, however when i check the sys file it didn't change. But I can start manually the systemd service and, this time, it works.

View 2 Replies View Related

Debian Configuration :: Installing Libpam-systemd

Aug 12, 2015

I upgraded my machine from Wheezy to Jessie, opted to not install systemd yet. When i try to upgrade kde-plasma-desktop, apt doesn't let me do it.

For some reason "libpam-systemd : Depends: systemd (= 215-17+deb8u1) but it is not installable"

Installing systemd-shim doesn't work. Libpam-systemd package site gives impression that you would be able to use systemd or systemd-shim.

Tried looking through changelog, but it didn't really give any hint.

At 215-6 there are just
Code: Select allSwitch libpam-systemd dependencies to prefer systemd-shim over
    systemd-sysv, to implement the CTTE decision #746578. This is a no-op on
    systems which already have systemd-sysv installed, but will prevent
    installing that on upgrades. (Closes: #769747)
Version of libpam-systemd that would be installed is "Candidate: 215-17+deb8u1"

View 2 Replies View Related

Debian Configuration :: Systemd - NTP Host Name Not Found

Apr 14, 2016

my system keeps on telling me about an error:

Code: Select allsudo journalctl  -p 0..3
Apr 14 10:36:11 debian ntpd_intres[682]: host name not found: ptbtime1.ptb.de
Apr 14 10:36:11 debian ntpd_intres[682]: host name not found: ptbtime2.ptb.de
Apr 14 10:36:11 debian ntpd_intres[682]: host name not found: ptbtime3.ptb.de

A quick check

Code: Select allsystemctl status ntp.service
ntp.service - LSB: Start NTP daemon
   Loaded: loaded (/etc/init.d/ntp)
   
[code]...

3 packets transmitted, 0 received, 100% packet loss, time 1999ms.Same result when using the standard Debian ntp time servers like "server 0.debian.pool.ntp.org iburst" in /etc/ntp.conf.

View 13 Replies View Related

Debian Configuration :: Laptop DVD Drive Is Acting Odd (blank) After Update

Aug 20, 2010

After the mass amount of updates that appeared for Debian, my DVD drive seems to detect a burned DVD I have as blank now. And when i put in the disc, there's two copies of the DVD drive on Computer, both of which are labeled CD/DVD Drive: Blank DVD-ROM Disc. I have gone in to disc manager and found that it is possible to mount the volume on the disc, and on the second icon it will appear and work. However, this is annoying having two icons.

Now, when I don't have a disc in there, it only shows one drive. My PC may have messed up during the updates, because I just let it update in the background while my sister was using it to show my mom's friends pictures and she randomly closed out of one of the windows without asking me anything (ffff), so that may have messed something up. Does anyone know how I would go about fixing this?

View 7 Replies View Related

Debian Configuration :: Enabling Persistent Logs With Systemd

Dec 1, 2015

How to enable persistent logging with systemd? I find it really weird that all this machinery that is systemd doesn't store persistent logs, what if I'm trying to retrieve some information regarding previous boots?

For instance: I have random suspend issues, after rebooting the computer there's no trace left in the logs of what happened, and furthermore (at least in Jessie) I can no longer see a pm-suspend log.

So, at first it sounds like all you have to do is edit journald.conf setting #Storage=auto to "persistent" and create the /var/log/journal directory, but then reading here /usr/share/doc/systemd/README.Debian

Code: Select allEnabling persistent logging in journald
=======================================

To enable persistent logging, create /var/log/journal and set up proper permissions:

install -d -g systemd-journal /var/log/journal
setfacl -R -nm g:adm:rx,d:g:adm:rx /var/log/journal

and here [URL] ....

There are two main reasons why I decided to not enable persistent logging just yet ....

We did get corrupt journal files in the past where the journal then no longer worked at all [1]. With volatile you can just reboot and have a clean state again. Admittedly, the journal has seen a lot of improvements in the mean time and hopefully is more robust, so this point is no longer true.

We still install rsyslog by default. That means we get store them twice. This is something we don't want to do atm.

View 3 Replies View Related

Debian Configuration :: Udev / Systemd Change Some Rules In 8.0

Apr 18, 2016

I have SSD drives without SCT support, because of this I want to tune /sys/block/device-name/device/timeout in order to force mdadm put these drives offline. So, I can see my drive like this:

/dev/disk/by-id/ata-OCZ-SABER1000_A22MJ061512000074.

Where can I tune /sys/block/device-name/device/timeout from 30 to 7 sec only for these drive? I don't want to use rc.local.

Can I create right udev rules for it in /etc/udev/rules.d?

I want to avoid any conflict with /lib/udev/rules.d.

Code: Select all# udevadm monitor --environment --udev
monitor will print the received events for:
UDEV - the event which udev sends out after rule processing

UDEV  [9302.549485] add      /devices/pci0000:00/0000:00:01.2/0000:03:00.0/host0/target0:0:0 (scsi)
ACTION=add
DEVPATH=/devices/pci0000:00/0000:00:01.2/0000:03:00.0/host0/target0:0:0
DEVTYPE=scsi_target
SEQNUM=5210
SUBSYSTEM=scsi

[Code] ....

View 0 Replies View Related

Debian Configuration :: Systemd Automounts For Removable Media Not Timing Out

Jul 18, 2015

I have the following hardware setup:

a NAS running Debian that frequently (but not always) has two removable media attached,a Debian desktop that mounts the above NAS via sshfs,the aforementioned removable media are symlinked to the directory on tha NAS that is then mounted by the desktop.

What I'd like this setup to do is to immediately time out if mounts as unavailable. Instead, I only get the expected behaviour if the NAS is down (the ssh client takes about 3 seconds to do that); if it's up, the removable media automounts (they are symlinked to the directory shared with the desktop) seem to never time out, ever. This happens locally on the NAS as well, when ssh'ing to the NAS and trying to run `ls /media/Storage` or `ls /media/Backup`, these commands never return. It's as if systemd was ignoring the x-systemd.device-timeout setting on the NAS.

The relevant part of the NAS's fstab:

Code: Select all/dev/sdb1       /media/Backup   ext4    defaults,noauto,x-systemd.automount,x-systemd.device-timeout=1s,rw,user,nofail,x-systemd.idle-timeout=30s       0       1
/dev/sdc1       /media/Storage  ext4    defaults,noauto,x-systemd.automount,x-systemd.device-timeout=1s,rw,exec,nofail,x-systemd.idle-timeout=5min      0       1

[Code] ....

I find it highly interesting that despite both removable media being detached, only one is flagged as having a dependency failed. Both paths exhibit the hang behaviour, though.

What can I do to actually time out when the media are not there?

View 4 Replies View Related

Debian Configuration :: Systemd Fails To Raise Up Network Interface

Mar 15, 2016

Is this a problem of systemd or network-manager however when I started to see this alert I noticed the nm-applet doesn't start automatically anymore.

Code: Select allsystemctl status network
networking.service       network-online.target    network.target
network-manager.service  network-pre.target       
zagor@Debian-635:~$ systemctl status networking.service
● networking.service - Raise network interfaces
   Loaded: loaded (/lib/systemd/system/networking.service; enabled; vendor prese

[Code] ....

View 5 Replies View Related

Debian Configuration :: Corrupted (permanent) Systemd Logs In Jessie

Apr 22, 2016

I've enabled permanent systemd logs in Jessie, and after a while I'm seeing messages about corrupted logs when checking with journalctl --verify

Code: Select allInvalid tail monotonic timestamp 0%
File corruption detected at /var/log/journal/..........

as far as I can see, there is currently no option to delete this files from within systemd facilities, is that correct?

Should they be deleted manually, or just left alone?

Apparently I can still read all older logs regardless of such reported corruption, using the journalctl --boot -n option.

EDIT:Another thing coming to mind is that this has been happening for me not only in Jessie but in every systemd-based distro that I've tried, once permanent logging is enabled: is that some kind of systemd bug?

What would exactly mean

Code: Select allFile corruption detected at /var/log/journal/38d5e6b861134eadb37cbd64b98a66bd/user-65534@d1745ac610d2459f940a24f27abd6d47-0000000000000f14-00051b8d2dabdcac.journal:000000 (of 8388608 bytes, 0%)

in particular, the 0% of 8388608 bytes part ?

View 0 Replies View Related

Debian Configuration :: Plex Media Server Startup Script Due To Systemd

May 6, 2015

My plex media server does not work with systemd apparently but running the command below makes plex startup properly

Code: Select all/usr/sbin/start_pms &

Is there anyway to make this command run on my computer at startup.

I am running debian 8 jessie.

View 4 Replies View Related

Debian Configuration :: Hardware Event Listening Scripts With Systemd Not Acpid

Aug 22, 2015

Just migrated to stretch, and noticed we're not using acpid anymore. Had couple of scripts at /etc/acpi/events listening for some events. What would be the alternative with systemd?

View 2 Replies View Related

Debian Configuration :: 8.3 LXDE Install - Laptop Goes To Sleep Mode Immediately After Boot

Feb 3, 2016

I have a strange problem in my new debian 8.3 LXDE install. Every time I boot my laptop it goes in to sleep mode automatically after a min. It is a default install and I have not configured any power management options. How do I find out the reason for the automatic sleep and how can I rectify it?

View 4 Replies View Related

Debian Configuration :: Kernel 2.6.38 In Wheezy?

Apr 11, 2011

This is Wheezy x86_64. I tried two different ways to install kernel 2.6.38 on my machine and both have failed. First thing I did was to follow this guide [URL]... el-26.html) and try to compile the latest stable from kernel.org. I don't know why, but it turns into kernel panic when I try to run it. Second thing I did was to install the liquorix 2.6.38, and that also fails, seeming to boot but hanging a second short from the login. I don't know what I'm doing wrong. Is there a special way to install kernels in Debian? This is the first time I tried compiling a kernel, so it's quite likely that the problem is sitting 6 inches from the computer screen. Also, how would I remove those kernels since they're obviously not working? I know I could remove them from the grub menu but I'm not sure how to completely delete them.

View 12 Replies View Related

Debian Installation :: Wheezy Network Install On Laptop No Keyboard Or Mouse?

Apr 19, 2011

anyway the reason for my posti downloaded a network install of wheezypartitioned and loaded wheezy on to a dell latitude d600now after installation the keyboard and mouse ( touchpad or nipple ) do not functionsince this inconvenience i have been plugging in a usb keyboard and mouse at the graphical login then using them to work the laptopAfter a reboot the usb peripherals do need to be uplugged and reconnected otherwise they also do not functioni am obviously missing something vital here but i am not sure where to start, kernel 2.6.38.2-686
i have loaded the non-free repos added the various firmware files etc. to get wireless and bluetooth to functionbut the keyboard and mouse has me stumped i have searched the forum and google but haven't come across anyone with the same issue.Some forum suggestions have been to reconfigure xorg.conf but this does not exist on this installevdev - the event driver is thereudev - the kernel device manager is also there

View 13 Replies View Related

Debian Hardware :: Laptop Headphone Jack Stopped Working On Wheezy

Apr 3, 2015

My laptop's (Acer Travelmate P243-M-6456) headphone jack had been working fine, and has no issues when booted into Windows, but it suddenly stopped working.

I've gone through alsamixer, and the volume is up, and nothing seems to be muted, and I've tried to do everything I could throughout the sound options in the Gnome System Settings.

Here is my ALSA information script output : [URL] .....

View 0 Replies View Related

Debian Configuration :: Migration To Bind 9.10 In Wheezy 7.1

Nov 13, 2015

I want to migrate to bind 9.10 in debian wheezy. I don't want to take the source code from debian Sid since its an experimental version. So I have taken source code from official bind forum and compiled in debian wheezy. The compilation is successful but I am having problem in running the binary in debian wheezy. It's not honoring the binary even though I run it. I am not getting error messages on console but still it is not running.

I want to know whether its feasible to do this Or is it dependent on any other system libraries to make it run ?

Last few lines from Strace Dump
==============================

capget(0x20080522, 0, NULL) = 0
capget(0x20080522, 0, {0, CAP_CHOWN|CAP_DAC_READ_SEARCH|CAP_SETGID|CAP_SETUID|CAP_NET_BIND_SERVICE|CAP_SYS_CHROOT|CAP_SYS_RESOURCE, 0}) = 0
getuid() = 1007

[Code] .....

View 1 Replies View Related

Debian Configuration :: Allow Root In Ssh On Wheezy Usb-hdd LIVE

Jul 15, 2011

I try to allow root login in ssh on wheezy usb-hdd LIVE using this script in config/chroot_local-hooks:

This script was working well during squeeze usb-hdd live creation.

View 5 Replies View Related

Debian Configuration :: High CPU Temp Wheezy X200

May 10, 2015

I am noticing some rather high CPU temps while using Debian 7.8 KDE on a Lenovo X200 laptop.

Even when its not doing anything its getting as high as 70C sometimes. I opened it up and went in with a can of compressed air, it went down a little to 36C now its back to 70c the day after.

Then I realised the fan was hardly spinning is there any way I can control how much (or little) the fan spins at certain temps?

My guesses are it could be done with a bash / shell script in the kernal loaded at booting up. But am unsure.

Here is my dmesg [URL] ....

And lsmod [URL] ....

View 2 Replies View Related

Debian Configuration :: Wheezy - Can't Change Software Sources?

Apr 13, 2011

I updated to Wheezy from Squeeze and whilst I can make changes to sources.list manually, I can't do some updates in Software Sources.For instance, the 3 check boxes under "Download from internet" are all un-ticked and I can't change them if I wanted to - even though the sources.list is set up with "main contrib non-free"I cannot amend the download server either - it works out what the best server is but wont update if I tell it to.

View 9 Replies View Related

Debian Configuration :: Installing Radeon Drivers For Wheezy?

May 27, 2011

I need some help installing the driver. I am very noob. so when I try to build a deb file with sh ati-driver-installer-11-5-x86.x86_64.run --buildpkg Debian/testing

# sh ati-driver-installer-11-5-x86.x86_64.run --buildpkg Debian/testing
Created directory fglrx-install.7aYYig
Verifying archive integrity... All good.
Uncompressing ATI Catalyst(TM) Proprietary Driver-

[Code]...

View 12 Replies View Related

Debian Configuration :: Manage GNOME Keyrings In Wheezy?

Jun 8, 2011

Last week I upgraded from Squeeze to Wheezy. Everything seems to be in order, except now launching empathy will get my 4 separate GNOME keyring prompts in a row. I guess my keyring got copied for some reason, but Ican't figure out what package to install to deal with my keyrings, as gnome-keyring-manager is only in sid...

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved