I start the pc then it comes the Normal Start Ubuntu page, where you can log by the username and password. I insert them then the monitor became black and then it comes again the ubuntu log page. I tried to remove the nvidia driver but the only thing that change is that now ubuntu starts in Reduce Graphic Modality
View 6 RepliesI am having problems getting my external monitor to work. When I plug in the monitor, both the laptop screen and the external monitor go black. When I unplug the monitor, the laptop screen works again.
When I startup with the external monitor plugged in, neither screen works or teh computer hangs or something.
I have had the external monitor going on a couple of occasions. I did manage to configure my monitors through System Settings > Display. I turned off the laptop monitor as I just want to use the external. But after rebooting, things didn't work.
I have a Thinkpad E420, Fedora 15
whenever I open system monitor, I just get a loada black and white lines, I have no idea what this is, this never comes for any other application/program and it stops me from being able to kill non-responding processes.
View 6 Replies View Relatedi tried to install linux mint, at first i got 'out of range' with black screen msg but used compability mode and got past it and installed mint on my HD. a moment after it updated my nvidia drivers and after reboot I got the out of range message again, which leaves me in the situation where i cant do pretty much anything I tried editing xorg.conf added VertRefresh 60-75 and Modes "1440x900_75.00"
View 4 Replies View RelatedI just install Ubuntu OS 11.04 recently to my HP Mini 110 netbook. When I try to display on my external 20inch samsung monitor. I get the black borders as shown on the pic. Resolution of 1024 x 768 or higher will cause the problem whereas lower resolution will not have that black border.
View 2 Replies View RelatedI have an Intel Corporation Mobile 945GM chipset. As I was playing around, trying to figure out how to get my dual monitor to work. The Mirror Screen was working fine, but then I uncheck the mirror screen option, both my laptop and my secondary monitor black out. I can only see the mouse, and it cans move on both screen.
Here is my xorg.conf:
Section "ServerLayout"
Identifier "X.org Configured"
Screen 0 "Screen0" 0 0
[code]....
I have this very frustrating problem... I'm trying to build a Linux-based HTPC (Home Theatre PC). I'm running Ubuntu 9.04 Jaunty as the operating system, and it works fine when I have it connected to my 17" Samsung monitor. However, when I connect the HTPC to the TV via VGA I get a black screen after "startx" (I can access the console through recovery mode though). Ubuntu is running gnome, so I guess it's a gnome related problem?
I would have thought it was a problem with the drivers to graphics card, but since it's working on my 17" monitor I've ruled that out. The TVs resolution is 1024x768. What can be causing this? Apperently there's some difference between my monitor and my TV (forgetting the fact that it is indeed a TV, not a monitor), but what? I've previously run Windows on the same hardware without problems, and thought I should give Linux a shot. It doesn't look good...
I did a LiveCD to USB install, following the directions I found at [url] When I went to reboot to the USB stick, all I get is a black Screen (monitor is on and lit, just nothing on the display) No cursor or command prompt. I've tried holding shift to bring up the GRUB menu, changing splash quiet to nomodeset, or just adding nomodeset after the splash quiet thing. I've even tried xforcevesa instead of nomodeset still black screen. Looking at the logs nothing is current as of the last time I tried to boot the computer, it's strictly what was written when I installed it to the stick. Other things I've checked/tried, Pressing CTRL+Alt+F1 at GRUB to get TTY, all I get is that blank screen. I've Checked etc/default/grub to ensure the timeout was higher then 0. The Install CD seems to be OK but I have (as it did another install successfully) but I haven't done any throughal checking of it (there was no check this disk on the first screen of the LiveCD) The USB sticks also seem to be ok (in windows though). Using the disk utility on the live CD I did check the file system on the USB stick, the "/" partition came up clean. Anybody have any other thoughts on this install, any thing else I can check?
View 9 Replies View RelatedJust did a fresh install of Natty B1 (previously had alpha 2).. I noticed this issue w/ A2, as well.. plugging in the exterminal monitor (via mini-displayport-to-vga connector) will do the following:
1) turn the screen on the laptop's display entirely black (but not turn it off).. i can move and see the mouse cursor.. but everything on the window appears to not rending or "painted" black..
2) external monitor never becomes active..
the only way to recover is to kill/restart X or reboot after disconnecting the extmon.. having extmon plugged in from boot produces the same results (and it doesn't seem to ever become active during boot up). sometimes this won't happen right away if i plug in the external monitor.. but opening the Monitors system prefs dialog will definitely cause (or detect displays) ,etc I waited to see if the issue would fix itself w/ the beta update, but it hasn't.. Any other 8,1 owners out there that can verify this issue? My (totally uninformed) guess is that it's due to differences in the display/gfx hardware and thunderbolt integration(?)
(I've seen a verification verifications of working-out-of-the-box.. but they were from 8,2 and 8,3 owners (which have discrete graphics cards))... If anyone's gotten this to work with some config stuff, I'd love to see that as well (since the wiki page for 8,1 says it works ootb). If someone could let me know where I should look to capture error output when the above issue occurs, that would be awesome.
I have just "finished" updating my Ubuntu 9.10. (somehow I knew that something is going to go wrong), and now my PC starts, works fine for a few seconds, then I get a black screen for a moment, and then my monitor starts acting like PC is off.Interestingly I think that otherwise everything is working just fine and that I just can't see anything due to the black screen (monitor is flashing like there is no signal coming from PC).
View 3 Replies View RelatedI've recently installed Debian v8.1 and installed Nvidia driver 340.46. In nvidia-settings I am able to enable my second monitor and enable it/set it's position..etc. My second monitor is not being detected in Debian Display and is 'on' but only showing a black screen. I've tried researching and implementing various 'fixes', but I'm not having any luck.
I'm running dual GTX 570's with a monitor plugged into one each (DVI). I noticed in my xorg.conf under Section "Screen" I have an option "MultiGPU" "Off"; would this be part of the issue?
I've tried:
- purging all nvidia drivers and re-installing
- installing different versions of nvidia drivers
- add nomodeset in grub
I got a used Gateway Solo 9550 from a friend. It was running windows when I got it. So I decided to try to test Debian on it. I am relatively new to the Linux scene so I have had a few issues with no idea how to fix them. The biggest one is video. I can get it the laptop to boot up in recovery mode and have nomodeset enabled. With nomodeset in gnome it will work for approx. 20-30 seconds, and then the screen will turn white then to black and then slowly turn rainbow. I know that its not a monitor problem because I ran DSL and DSLN on the same rig, but when I plugin an external monitor its fine on the external but not on the internal.
Specs of the Solo 9550
1 GHz Pentium 3m Processor
512 MB of PC100 RAM
Geforce 2Go 100/200
on a 6-7 years old compaq laptop, connected to a brand new hp monitor i am having a mismatch with computer/monitor resolution.
before i had ubuntu 10.04 which could only run in x's safe graphics mode - allowing for full screen resolution but with handicapped graphics - for example videos fullscreen would be quirky and run with cpu at 100%, something which was no problem before 10.04.
then i tried ubuntu 10.10 and later lubuntu 10.10 (which had exactly the same problem); the monitor is running 1440x900 while the computer is rendering to only 1024x768 - leaving a huge black border on right and bottom of screen. the gfx is still crippled; videos fullscreen is quirky as before.
I am booting XP and Opensuse 11.4 all was ok until I changed my old monitor for a widescreen monitor, Xp works ok but when I select Opensuse from the menu it just boots to a black screen.
View 3 Replies View RelatedI could easily go to ms system monitor display by clicking on background of desktop and finding it through there to change settings related to desktop. I want to be able to watch a movie without the desktop screen saver thing going off. where can extend it to longer than 2-3 minutes on linux mint?
View 8 Replies View RelatedI have an Asus z9100 laptop with an Intel 855GM integrated graphics chip, which is running Karmic (the purpose of the laptop is to be a MythTV frontend so my understanding is that it needs to run 9.x in order to connect to the MythTV 0.22 backend - I have installed and configured this using the installable Mythbuntu package) and the laptop is subject to this bug which causes random freezes:
[URL]
So, following advice for similar freezes I've seen, I have added the following options to my grub menu.lst on the kernel line:
nolapic nomodeset
and I have edited xorg.conf so that it makes use of the vesa driver instead of the Intel driver. This results in no freezes and if I wanted to watch Myth on the laptop screen I'd be squared away. However, the laptop has a damaged screen so the point was always to output the signal to an external monitor via its VGA out.
When I attach the external monitor and boot with the setup as described, the external monitor is never detected. But I noticed that if I remove the "nolapic nomodeset" from the kernel boot line, it is detected. However, signal is only output to it during the earliest part of boot (when the Ubuntu logo is in the center of the screen before the full-screen graphic with the animated progress line), after which the external monitor goes black and all the display output goes to the laptop screen. The external monitor power button is still lit up green as if it has been detected and is receiving signal, but it's just a black screen.
get the signal out to the external monitor after the initial part of the boot process, using the vesa driver? Here is the current state of my xorg.conf:
Code:
Section "Device"
Identifier "Configured Video Device"
Driver "vesa"
EndSection
[Code].....
what it is, is I installed Maverick fresh (not an upgrade) and it now will go to were it says ubuntu, and has the loading dots, and it stays at a black screen after that. The 'thinking' light for my computer is not activationg. it is installed on a 20-30 Gb partition, on a dual boot with windows 7. I had had Lucid installed a while ago, but it was lost when my harddrive was wiped a while back. My specs:
Computer: Lenovo g555
CPU Type: AMD Athlon II Dual-Core
CPU Speed: M320(2.1GHz)
CPU L2 Cache: 1MB
HDD: 160GB
[Code]...
Well my problem is described simple as that Black screen on start up. y laptop became a bloodless zombie after I installed BOCHS, Avast 32 bits (forced architecture) and the one I think may be the problem: Driver Manager or something like that wich is PySDM I think. This one is supose to configure mi Hard disk to automount.
View 2 Replies View RelatedTo start this is on my mom's laptop which is a Gateway NV78.
It was running fine with Ubuntu 10.10 but I like to do a clean install of the latest version when it comes out and I am home. I torrent the 11.04 desktop 64 bit releaee and strangely the screen is just black but it appears to load. Then I try to the 64 bit alternate install which appears to work fine. Unfortunately, the screen is black when loading past GRUB and plays the Ubuntu sound. To test if it is loading I type in my password and hit enter and the Ubuntu log in sound plays but still nothing on the screen.
I thought no big deal I will just install 10.04.2 and use the alternate download. I download it on the desktop running Windows 7 and use the USB installer the Ubuntu website recommends. It installs fine but the same problem occurs with a black screen.
At this point I think to reinstall again but this appears at the top of the screen.
SYSLINUX 3.86 20-04-01 EBIOS Copyright (C) 1994-2010 H. Peter Anvin et al
The screen is just stuck there with a blinking cursor and if press any keys it beeps several times.
TL;DR Installed 11.04 then black screen. Installed 10.04.2 then black screen. Install 10.04.02 again and error message.
I have a laptop and an external monitor connected via displayport. I can configure both displays via settings with correct resolution and arrangement. However, this configuration is not sticking, and every time I shut down the laptop or close the lid I will need to fight with black screens and more to bring the same configuration again. Basically, it seems that the monitor is "stealing" the primary role to the laptop's native screen (I have it configured as secondary, but also being primary the configuration gets messed).
After many trial & errors, this is the routine I have found to make things work every time I boot / awake the system:
1. Boot. Laptop's display shows the booting sequence.
2. When the login screen should appear, laptop's display goes black, monitor shows background.
3. If I press F9 to increase brightness, the brightness icon appears in the monitor, but it is stuck at the minimum.
4. The only way to leave this point is by pressing F7 (project screen) and then F9 again to increase brightness. Then the laptop's screen does light up.
This is when I'm lucky. Sometimes the configuration goes mad and I get mirrored displays and different resolutions, without touching the settings myself. Also, if I unplug the displayport I run the risk of getting stuck with a black screen in the laptop, without any way of recovering the GUI other than rebooting (Ctrl Alt F2 will still show the command line screen).
My system is Debian 8 testing up to date, running in a Lenovo T430 with Intel components. I'm not sure the monitor is relevant here, but in any case it is an Eizo CS240.
I just recently purchased a DELL PowerEdge 2850 and have tried installing CentOS 5.4 on it. After the install completes and it does a first boot I get the following error on the DELL console: PROC 1ERROR, PROC 2ERROR E07F0. The monitor remains black and the system hangs. Just out of curiosity I installed Fedora 11 on it to see if it was a hardware problem. Fedora installed and booted no problem. I rebooted with Fedora installed several times and left it running for 24 hours. Everything is working great. Is there something I am missing in the CentOS 5.4 install?
Below is the Hardware Config:
Dell PowerEdge 2850
PERC 4eDi RAID Controller
8GB PC-5300 ECC Memory
2 Intel Xeon CPU Dual Core 2.8GHz 800FSB 4MB Cache - SL8MA
ATI Radeon 7000 Video Card
Well my friend just gave me a Cd so i could switch back to windows vista but when i run with starting cd rom and i press any key to start cd or dvd it goes black with a blinking thing on the top left corner i went to sleep for 2 hours hoping it would be done when i get back but it was still there
View 1 Replies View RelatedSo I got Ubuntu installed alongside my Windows, but now when I start I get a message on my monitor saying about input not being support or something; usually happens if the resolution isn't supported. If I hit random buttons eventually Ubuntu will start up, but I don't want to be doing that every time I remember when I had an older version of Ubuntu a screen would appear where I could pick to start either Ubuntu or Windows, so I assume that's what's going wrong.
View 9 Replies View Relatedl have install Itunes through wine , but the problem is that when a want to start iTunes the screen is getting black !?And also when l try to uninstall the screen is getting black.
View 5 Replies View RelatedI'm a newbie to installing LINUX (was an Oracle DBA for many years) and I am having trouble getting the dual head function to work with my Sony Vaio laptop. I just select a generic LCD with the screen resolution that I want, but when I startx, I briefly get the login window (terminal), then everything goes blank and I have to unplus the samsung monitor and reboot to be able to have a screen again. I have tried the fn + f keys and that doesn't help.
Here is the hardware:
Samsung Syncmaster 2343BWX
Sony Vaio VGN-FJ170
Intel Graphics Mobile 915GM/GMS/910 GML Express graphics controller
I would like to use this laptop as:
Audio streaming from internet (so far not working on my local NPR stations)
Hooked up to KVM switch - using the Samsun monitor and an adesso integrated keyboard
Wireless network (that is working - but it took some doing....)
What files and logs I need to post I will do so, but if what I want to do is just not possible or a big hassle, please just let me know, and I will load windows. Although I really wanted one LINUX box in my home office.
I cannot install Ubuntu 10.04, or even boot into the live CD. I'm not an expert, but I've used Ubuntu for several years, and I'm pretty sure I'm not doing anything stupid... Here's what happens when I boot with the Ubuntu 10.04 live CD: I get a purple screen with just an accessibility(?) symbol at the bottom (this lasts 15 seconds). The screen goes black, with a flashing cursor, then changes back to purple, this time with an Ubuntu logo, with 5 dots acting as a progress indicator (this lasts about 1 minute). The screen switches to standby. The CD drive continues to make noises for another minute or so, then stops.
I physically removed my graphics card (ATI Radeon HD 5770), and plugged the monitor straight into the VGA port on the motherboard. Now the CD boots up fine. I could try installing Ubuntu at this point, while my graphics card is unplugged, and then plug my graphics card back in, and see if it starts working then.
A few weeks ago I installed Ubuntu 10.4 beta on a pc. I upgraded it to 10.4 RC and 10.4 final release. I think it was after upgrading to 10.4RC that I started having a problem during startup. Here is what happens:
I turn the pc on the bootstrap process occurres, then the grub screen comes up I let ubuntu boot. For a few seconds I get a black screen with a blinking cursor. The Ubuntu splash screen flashes on the screen for maybe a second or two. Then I'm dumped to the command prompt on TTY1.
At this point I can log in with a username and password type startx and I'm at the ubuntu desktop. If I log off I'm back at the command prompt on TTY1. If I press alt-ctrl-F7 at the command prompt this is what I see, these are the last four lines of text: init: ureadahead-other main process (742) terminated with status 4
[Code]...
I am doing a new install of i86_64 on a system with a wide 22" monitor. The initial screen displays fine but after selecting "new install" the monitor becomes alternating black and white horizontal bands. the cursor is visible and tracks the mouse. The monitor is an Acer with fixed 37kHz horiz x 60 Hz vert. I assume that the gui is using a fixed (and different ) set of frequencies and is not plug-n-play. I just finished an i386 32 bit installation on another machine which went without a hitch.
View 4 Replies View RelatedI am a both rhel5 and fedora user.I can not configure my Samsung syncmaster 632nw monitor to display full screen at 1360X768.There is huge black space both left and right side of the monitor. I have tried many times to solve it but unable to do it.The max screen resolution is 1024*768 and minimum is 640*480.
Here is the xorg.conf file:
ubuntu 10.10 64 bit i try to change graphic card it have some problem bit about colour an old i use ship of nvidia gforce 200 series but when i change to nvidia gforce 7900 i login it's show in black screen mode . ubuntu 10.10 name-desktop tty1 name-desktop login: _
View 1 Replies View Related