Whenever I close my laptop lid or just press the suspend button, it will go to sleep just fine. Perfect. Waking up is the problem. The drive light flashes for a few seconds, and then it just goes to back to normal but my display is still busted.
View 9 Replies
I'm running 9.10, how do I wake up from sleep or hibernation on my Dell XPS notebook? I have no problem putting the comp to sleep/hiber but can't seem to work out the keys to wake it up again.
I don't get any responses from the keys even when I try CAPS LOCK or NUM LOCK, so all I can do is reach for the on/off switch.
I am running Ubuntu 9.10 on my desktop and everynow and then I get this annoying problem. If I walk away for a bit, just upstairs to use the bathroom, sometimes when I come back the monitor is off and the power light is blinking. You know, like what monitors usually do when they are still powered on but the screensaver is done playing. However, this happens to me well before the 10 minutes that the screensaver is supposed to end.
It does not always happen, and I can't really isolate what may be causing it, as I never take a note of what I'm doing when I go pee. HOwever, I rarely do anything other that run VLC, Chrome, Firefox, or OpenOffice Writer.
The problem is that the screen won't wake up. Moving the mouse does nothing. Jamming some keys does nothing. Trying to go to text terminal does nothing. I have to either REISUB or hold down the power button on the tower.
I just recently got my old box back and now I'm running 10.4. I've had some minor issues that I have got through but now there is one which seems to really be frustrating me. At any random time my monitor may go black as if it is in sleep mode. The problem is when it does this, no mouse movement or keystroke will wake the thing up. So I am forced to press the power button. When I press the power button the Ubuntu logo pops up on the screen as if it magically woke up but it is too late because now the computer is shutting down... When I go to System>Preferences>Screensaver I get to the options for the screensaver and I have about 2 seconds before that triggers the screen going black.
I can't even start until I know that my screen won't shut off at any random moment!
I'm having some trouble getting Ubuntu Netbook Edition to work properly on my Netbook. If I close my netbook for long enough for it to go asleep, which only takes 10-20 seconds, then when I open it back up and press the power switch, nothing appears on the screen.
View 3 Replies View RelatedI have an interesting issue. I have a computer running Ubuntu 10.10. I have a wireless USB Microsoft keyboard attached to this, and I have a cheap USB infrared remote also attached to it.The wireless USB Microsoft keyboard can wake up the system from suspend. The USB infrared remote cannot.To start off, I made sure my /proc/acpi/wakeup had wakeup enabled for all usb devices.
Code:
xbmc:~$ cat /proc/acpi/wakeup
Device S-state Status Sysfs node
[code]...
I have installed Debian 8.1 with KDE desktop on Lenovo t431s with intel HD4000 graphics.
When using it with dual monitor configuration, I experience the problem when I put system to sleep (by closing the lid), then remove the external monitor cable (from miniDP port) and then try to wake system from sleep. The login screen freezes and I am unable to move the mouse or type in credentials. In case I had music player running I can hear the music after system wake , but it shutters while playing.
This does not happen on some other distributions, but the problem is that I very much like my current setup and I would like to fix this problem and keep it.
I do not know if this problem is due to KDE or KDM or it's Debian base.
I've configured my F12 system to go to sleep when idle for a period of time and so far everything has been working out well except that it appears that the USB ports are completely dead with the system is put into sleep. I can't wake it using keyboard or mouse. only with the power button. Anyoen else experience this or know how to allow sleep from keyboard/mouse?
View 14 Replies View RelatedFirstly, wol works fine from shutdown and hibernate; it's just suspend which doesn't work.
I've got 2 types of workstations, all running 11.1. They both have this kernel:
2.6.27.45-0.1-default #1 SMP 2010-02-22 16:49:47 +0100 x86_64 x86_64 x86_64 GNU/Linux
Type 1 is a dell optiplex 745, bios version 2.4.1. Here's the relevant bit from lspci:
03:00.0 Ethernet controller: Broadcom Corporation NetXtreme BCM5754 Gigabit Ethernet PCI Express (rev 02)
Kernel driver in use: tg3
Kernel modules: tg3
[Code]....
The fact that it's happening across two different machines makes me wonder if it is some OS setting I've missed, but then maybe neither card/driver supports it from suspend.
I'd really like to get them waking from suspend because training users to use suspend rather than hibernate would be a pain. Also, being able to configure such that it only wakes from suspend and not hibernate/shutdown, as implied in the bios, would allow me to wake machines up for backups etc only when the users are here, rather than on holiday/seconded to another department etc.
My laptop won't wake from sleep. I hit the powerbutton and it'll blink a few more times, turn green and the keys will light up but the screen stays black.
Running sony vaio s with windows 7 and 11.4 duelboot. I really need it to be able to suspend and wake because I'll be taking it to college in the fall.
Is it possible to let a Linux PC put itself into sleep mode at 1 am, and wake up, by itself at 6 am?
View 14 Replies View RelatedIs there any way to find out which device/event caused Ubuntu (10.10) to wake up from the most recent sleep/hibernation? I am trying to troubleshoot some sleep issues on a new box, and knowing what's causing it to wake up would help. I did check /var/log/pm-suspend.log but all it seems to say is Sat Dec 11 22:18:27 GMT 2010: Awake.
View 1 Replies View RelatedI have set up a hdparm configuration file ( /etc/udev/rules.d/50-hdparm.rules ) with :
Code: Select allACTION=="add", SUBSYSTEM=="block", KERNEL=="sda", RUN+="/usr/bin/hdparm -B 255 -S 0 /dev/sda" .
This works correct when I power on my system, however after waking my computer from sleep mode , /dev/sda appears to operate with APM .
Is there a way I can make this setting to be persistent ,i.e. APM disabled when waking up from sleep mode?
I am running Debian Jessie x64.
I have openSUSE 11.4 KDE (upgraded to Tumbleweed but that's not relevant here). The computer is a Dell Optiplex. My sleep (suspend to ram) and wake (restore from ram) work very well. The box can multiboot to windows 7 as well as to Linux.
In Linux, the restore process is triggered by pressing the power button on the front of the case. No other action will bring it awake.
In windows, the restore process is triggered by the power button but also by moving the mouse or touching the Escape key, spacebar etc.
Here's the question: how do I get the computer to wake in Linux by activating a key (or mouse, whatever) instead of just the power button (which is under the desk and hard to get to)?
This morning I woke up and while my computer was turned on, I couldn't wake my monitor up from "sleep". So I turned off the computer and turned it back on. I noticed that the normal boot screen (which usually shows a monster truck from Abit) was pretty severely distorted.Basically all output to the screen is so distorted visually that I can't tell what's going on. I've attached two images that I took below:
The first image is at the very beginning of the boot (perhaps when the monster truck should normally show <- sometimes it shows and sometimes it is just too distorted to tell anything). The second image is after it's been on for about a minute, and you can see a little text box giving me some sort of warning (which I of course can't read). I can click "OK" or something along those lines by using they keyboard though and progress to a new warning box, but again, can't read what they say. How can I figure out what the problem is?s it definitely a videocard thing, or could this be caused by anything? I don't know if it's a software problem (running Ubuntu 10.04), or if something went wrong with my hardware overnight.
new to Ubuntu and enjoying using it, trying out Ubuntu as an alternative to vista, the only thing i have been able to do is suspend and then wake my pc, it fails to wake, is there a workaround for this
have changed settings so pc sleeps after 1 hour, it was on never, i,m running ubuntu9.10 my pc will wake but i have a black screen with mouse icon showing but i,m unable to get any response, all well again after a reset
put pc in suspend and went out, on returning home started pc via on/off switch instead of pressing space bar (any key) hey presto Ubuntu woke up no problem
I want to run a script on wake but it doesn't look like /etc/acpi/resume.d exists in Lucid. I tried creating it anyway, but I didn't have any luck. Is this because HAL has been removed? Is there a new method in Lucid?
View 3 Replies View RelatedI'm running Linux Mint 9 (aka Ubuntu 10.04 + a couple of tweaks), and my machine won't wake up from suspend.It hasn't done so successfully since Ubuntu 8.04. I'm running the default graphics driver (not the proprietary NVidia one) on a quad-core Gateway FX. How can I go about figuring out the problem?
View 5 Replies View RelatedI am trying to conserve electricity and was looking for a linux WOL app that will allow me to remotely wake my windows 7 computer so I can stream music on demand. I have to believe this exists/is possible. I am also an idiot so if there is such a thing I'm going to need help getting it up and running.
View 6 Replies View RelatedI upgraded my old HP Pavilion desktop to 11.04 a few weeks ago and at first things were fine, but recently the PC refuses to wake up in the morning. I assume it's going in to sleep mode overnight, but no matter what I push on the mouse or keyboard it won't wake up. I have set both the PC and screen in Power Management Preferences to Never go to sleep, but it doesn't seem to matter and it sleeps regardless. how I can either make it not sleep, or sleep a little lighter so it wakes up without a hard reboot?
View 1 Replies View RelatedAll I want to do is to be able to shut the lid on my laptop, have it go into suspend like it already does, but upon opening it again, successfully start up again. It'll sleep just fine, but if you close the lid and try to open it again later, the lights will indicate it is starting up, but the screen won't initialize, and I am left with a blank, black screen.I've tried a line of code to enter into my menu.lst file, and it seemed like it should work, but it borked my computer and I had to manually reinstate the line of code it had before.
View 9 Replies View RelatedI have managed to make ubuntu (9.04) turn itself on from being completely off with the following code:
Code:
sudo sh -c "echo 0 > /sys/class/rtc/rtc0/wakealarm"
sudo sh -c "echo `date '+%s' -d '+ 480 minutes'` > /sys/class/rtc/rtc0/wakealarm"
[code]....
I have made a virtual machine on my server using virt-manager that I access using virt-viewer from my desktop/laptop. Currently I am having to leave the VM on all the time. Which is a waste of cpu/ram etc. Ideally I would like to be able to wake the vm up from virt-viewer or from a bash script being ran on my desktop.
View 1 Replies View RelatedI have a macbook5,1 with ubuntu 9.10 on it. Does anyone got wake-on-lan working on this type of machine (or any other intel macbook?)
At startup, ethool sets the wake on lan parameter. I tried sending the magic packet with the wakeonlan utility.
I can Suspend or Hibernate my Gateway notebook but I have no idea how to wake it up.The power button is set to suspend or hibernate....I not sure which it does, but I can't wake the computer up.
View 9 Replies View RelatedFor some reason when I wake my computer up, there is no sound. No matter what I try through the terminal, or by playing with the volume controls, no audio. I can only get audio working again by a restart.
Does anybody know why, and/or how to fix?
I'm trying to get WOL to work on my web server built on an ASUS P4A800D-X motherboard (which supports wol).I have it enabled in my BIOS and I've tried several different tools with no results, including my dd-wrt based router which has this functionality built into the firmware.All the guides I've read say it has to be enabled in the driver settings in the Windows Control panel before it will work, but I'm running Ubuntu Server 10.04.
Is there any special steps that must be taken in the OS to enable my web server to power on from the LAN? I've never used this feature before and would like to just shove my web server in a corner some where and have 100% remote control from my main PC.
how to get WOL over the internet. I have a server which i only use for development and would rather it not be on all the time. But i need to be able to access it when im out
I have WOL working over the LAN. SO next step is internet.
Ubuntu 10.04 LTS
My computer runs really well when I first switch on, and usually I'll leave it on all day, and just suspend it when I'm not using it.But since a couple of days ago, it's been playing up after waking from suspend. Everything slows to a crawl, and the system monitor shows the CPU working at 96-100% permanently, even when I'm not doing anything.It's not like I even have many apps open. Generally I'll have a few tabs going on Opera, have Thunderbird open, and Gwibber. I'll open and close gedit and gimp as I need them, and that's about it. Having said that, this new version of Thunderbird seems very slow to me compared with the previous one.
View 2 Replies View RelatedThere's any program like this for ubuntu?
View 7 Replies View Related
