Slackware :: Getting A Bit Ridiculous To Have To Run Run Xp In A Vm?

Feb 23, 2011

This has been an on going problem since 13.1 was released, but this morning was the last straw. I was printing off pages from a web site and it was taking, seemingly, forever. I finally started up VirtualBox and in that Xp, and went to the same web site and started printing one of the same pages. In Xp it printed in 1/4 of the time it took in Slack. The question is, Why? It is HP 940c and not a windows only printer. It is getting a bit ridiculous to have to run run Xp in a vm to do, with any speed and quality, basic things such as scanning, printing and using Bluetooth to communicate with my cell phone.

View 8 Replies


ADVERTISEMENT

Networking :: VirtualBox Bridged Adapter + 8021q = [b]ridiculous Performance[/b]

Oct 15, 2010

I'm configuring a CentOS 5.5 2.6.18-194.17.1.el5.centos.plus server in order to have multiple VirtualMachines in it. The throughput of the machine is at least 300KBps (yes KB), I configured two web servers one on the virtual machine and the other in the physical machine, the difference was: 300bps-3 KBps on the virtual machine, 230KBps on the physical machine.

The configuration is as follows:

Code:

If I attach the public ip address to the virtual machine this gets smoothly.

View 1 Replies View Related

Slackware :: Installing 13.1 Over Windows XP - Run Slackware And Slackware Only

Dec 19, 2010

I have been given the task to install slackware 13.1 over windows. I have downloaded and copied slackware 13.1 on to a disk, and rebooted the computer, but i am not getting what all the tutorials have shown. I have been looking for tutorials that specifically instruct me as to how to install slackware 13.1 on to a windows xp. I am not trying to dual run I just simply want to run slackware and slackware only.

View 5 Replies View Related

Slackware :: Forwad X11 From A 32 Bit Slackware To A 64bit Slackware?

May 7, 2011

I have a couple questions about Xfoward.

1: How much does it affect securty, over a lan network?
2: Will it cause any other security issues?
3: The most important is can I forwad X11 from a 32 bit slackware to a 64bit slackware

View 1 Replies View Related

Slackware :: Compile 2.6.37 Kernel Patched With The Autogroup Patch On A Slackware 13.1 System?

Jan 13, 2011

it's possible to compile the 2.6.37 kernel patched with the autogroup patch on a Slackware 13.1 system running 2.6.33.4-smp with 2.6.33.4 headers? I just compiled and installed the 2.6.37-autogroup kernel from AUR on my ARCH setup and I like it especially when using firefox with lots of tabs open and other background apps also running. I did notice a speed and smothness difference in my ARCH testing setup with this kernel patch and I can get same results in 13.1??

View 1 Replies View Related

Slackware :: Failed To Initialize NVIDIA Graphics Device On Startx With Slackware 13.1

Aug 24, 2010

I installed slackware 13.1 x86_64 bit with multilib, and its been about a month already, I'm really enjoying slackware but I am being troubled with my nvidia card, and I need to get my 3D acceleration working. And I've been looking around the net for information and kept on trying to make my nvidia card to work but to no avail. I cant get X to start, once I put in a xorg.conf stating to use the nvidia card. After troubleshooting for almost 2 weeks and now at my wits end, I now come humbly looking for help in linuxquestions slackware community forum.I've installed nvidia 64 bit kernel, drivers from slackbuilds (version 256.44). The laptop model I'm trying to get it working is an -ASUS K52J Intel Core i3 2.40Ghz with 2GB RAM and with an Nvidia Geforce 310M with 1GB dedicated VRAM.

View 14 Replies View Related

Slackware :: Enable Windows Wireless Drivers In Slackware 13.1 And How To Install XFCE

Aug 22, 2010

I recently installed Slackware Linux 13.1 , and my Wireless is down. I've only installed 3 Linux disto's on my main laptop (Ubuntu 9.10 , 10.04 , and Crunchbang Linux 9.04 , just had Crunchbang), and they all had the same problem. In all three , I was able to enable Windows Wireless drivers and every thing worked. Now , I'm assuming I have to the same ting in Slackware? Sorry , but I have no idea what my wireless card is. But I know that my laptop is a Dell Insprion E1705. One last thing , I did ifconfig and that wlan0 is my Wi-Fi interface. I typed ifconfig wlan0 up to see if that was the problem. After I did that , I got and error message. Then I typed ifconfig wlan0 down to see if it was down and it made wlan0 down. I tried bringing it up again , but I got an error saying it couldn't find the device specified. Also , how do I install XFCE? I really don't like KDE for some reason and would like to install XFCE. I chose XFCE over GNOME (my favorite) because I want to try something new.

View 4 Replies View Related

Slackware :: Linvo 2009.1rc6 - Slackware-based LiveCD With GNOME

Jan 6, 2010

I'm happy to announce Linvo 2009.1 rc6. It's a full-featured Linux distribution with a lot of applications by default, including an office suite (OpenOffice.org extended with plugins), a good internet browser (Firefox extended with plugins), a music player that supports music collection and a lot more - Exaile, a video player, and all the available codecs. It can open all types of file formats. It's a LiveCD, which means that you can test it without installing and after this optionally install it - it has a nice easy graphical installer.

It's the first Slackware-based LiveCD distribution with GNOME by default. It includes NetworkManager and initng in place of sysvinit. It also features accessibility tools. It is also the first release with the innovative portable applications system. This allows you to download application from the site (modules section), place it where you like, and use it. It's just a single file, no directories. You can also use this application without installing it, directly from the internet. However, after this, the speed of the application is limited by the speed of your connection, of course. Check out the "Applications" section on the website.

Besides this, you can install software with the apt-get-like system "slapt-get" and it's graphical front-end: GSlapt. It also contains src2pkg and sbopkg in case you want to compile something from source or existing SlackBuild Depfinder is included to find dependencies of packages. Click here for a guide on how to use those. I also managed to put development tools in there, like GCC, G++, svn, cvs, so on... This is a release candidate, and despite that it's OK for using. It has a bit more things to do until the release (like language selection on the boot menu), but I decided that it's important to put it here for testing.

View 11 Replies View Related

Slackware :: Lost Wireless Keybord And Mouse Upgrading Slackware Current

Oct 24, 2010

Lost my wireless keyboard and mouse upgrading slackware current.Boot seems to be normal.I just can't login, cause have no keyboard.

View 2 Replies View Related

Slackware :: Pkgbuild - Modern, Multi-architecture, Package Builder For Slackware?

May 25, 2010

We are pleased to present one of our new creations: pkgbuild, a tool written in standard C++, using libCURL, ZLib, BZip2 and libLZMA (part of XZ). It is a modern Slackware packages builder, network-transparent, multi-architecture, designed to greatly simplify the creation of a package, automatically executing the required post processing.

What does it do? Recognize and build packages for the following architectures: i386, i486, i586, i686, x86_64, IA64, IA32e, s390, s390x, sparc and sparc64.

[Code]...

View 14 Replies View Related

Slackware :: Enable Ling Separate X Sessions With Dual Monitors In Slackware?

Jun 29, 2011

how to on enable ling separate X sessions with dual monitors in slackware? In rhel all I have to do is enable it under the nvidia-settings... In slackware it does not work that well... to what I understand you have to configure a separate x session...

View 11 Replies View Related

Slackware :: Slackware 13.1 VIA VT1708S Audio Driver - Get Working Without Rebuilding The Kernel?

Jun 23, 2011

I'm trying to bring my Slackware system back to life as my XP HDD is dying... I've got everything working except for my audio. I got a new motherboard (ASRock P43DE3) and it has a VIA VT1708S as the onboard audio. Is there any way I can get this working without rebuilding the kernel?

View 5 Replies View Related

Slackware :: Static Libraries - Why Aren't They Shipped In Official Slackware Packages

Aug 12, 2010

I noticed that the official Slackware packages don't contain static libraries. The SlackBuild scripts from slackbuilds.org or from Slackware DVD usually contain --disable-static option to prevent building the .a file. And if configure script doesn't allow such option, the .a file is deleted before the package is created.I am wondering what is the reason for that? Is it just the matter of conserving disk space? Are there also other reasons?

View 11 Replies View Related

General :: Installing Slackware On IDE Hard Rive Boot From Slackware DVD?

Jan 23, 2010

I try to install Slackware to my IDE hard drive and boot first from Slackware DVD. After I loaded huge.s kernel, and tried to partition the hard drive using fdisk by entering "fdisk /dev/hda", I found out that the partition size is max to 3 Gigs instead of 80 Gigs.

I think the kernel is looking at my boot disk, which is around 3 Gigs. How can I make so that it looks at my IDE drive instead at my boot drive? Is there any manual that shows me how to install Linux from scratch this means I want to wipe out all my hard disk and install Slackware Linux there?

View 2 Replies View Related

Slackware :: Alfa AWUS036h Rtl8187 Adapter Not Working On Slackware 13.1

Oct 13, 2010

I recently bought the Alfa AWUS036h which uses the Realtek rtl8187 chipset. I am able to load the module and connect to any network, but its almost as soon as I try to load a page the connection drops. It never stays connected for more than 30 seconds. My other computers using the same adapter in the same spot work fine, unfortunately there not running slackware. I've tried compiling the newest stable kernel and checked the rd.inet1.conf settings.

View 6 Replies View Related

Slackware :: Alfa Awus036h Slackware Current Dhcpcd Won't Connect

Feb 5, 2011

slackware-current kernel 2.6.35.10-smp for instance if i just want to connect to wep ap. i done

[code]...

it says waiting for carrier and it just time out, im wondering why i read somwhere that its not working good with slackware 13.1

View 9 Replies View Related

Slackware :: Installed Multilib Support In 64bit Slackware 13.37 Installation?

Jun 28, 2011

I have installed multilib support in my 64bit slackware 13.37 installation than I proceed it to install google earth from slackbuilds... and did ln -sf /lib/ld-linux.so.2 /lib/ld-lsb.so.3Now when I try to run google earth I get:[ 760.092745] googleearth-bin[3647]:segfault at 984f7d31 ip 00000000984f7d31 sp 00000000ffbfe100 error 4

View 14 Replies View Related

Slackware :: Install Binary Blender 2.49b On Slackware 13.1 86_x64 Multilib?

Dec 12, 2010

I created this small how to install the binary Blender 2.49b on Slackware 13.1 86_x64 Multilib.

http://wiki.blender.org/index.php/Do..._Blender/Linux

View 1 Replies View Related

Slackware :: Script Which Will Take Patches Subdirectory Of Latest Slackware Distribution

Jan 10, 2011

Is there a script which will take the patches subdirectory of the latest Slackware distribution tree, and substitute the new patch txz files for the ones in the slackware subdirectory so that during an ISO install, the latest txz will be used, instead, and the ISO will be minimized by not having the older ones?

View 6 Replies View Related

Slackware :: Can't Reach Main Slackware Directory - Login Required

May 20, 2011

The Slackbook reads:

Quote: The precompiled Slackware kernels are available in the /kernels directory on the Slackware CD-ROM or on the FTP site in the main Slackware directory. I am unable to reach it, what's the proper login?

[Code]....

View 3 Replies View Related

Slackware :: Crashed Shiny New Slackware System Into The 99 Error Wall?

Jan 14, 2011

pls delete this post if I should not do this as it is included in [URL]..How do I recover from the 99 error when I start my system? I can only get to my Slackware by booting into it from the Slackware DVD.I have re-run lilo but I keep getting the 99 error on start up.

View 10 Replies View Related

Slackware :: Install Puppy 525 On Slackware 13.37 PC As A Dual-boot Using LILO?

Jul 18, 2011

I'm trying to install Puppy 525 on my Slackware 13.37 PC as a dual-boot using LILO. Puppy is living, all on it's own, in sda6, a 6 GiB partition. It got there by using the Puppy Universal Installer and selecting a 'Full' install, not a 'Frugal' install. I cannot find 'LILO' type instructions, only 'GRUB' type instructions.

Has anyone succeeded in doing a hard drive install of Puppy with the LILO boot loader?

Edit: I'll probably regret it, but I used Puppy's GRUB installer.

View 17 Replies View Related

Slackware :: Missing The Flash Plugin Using Slackware 13 64bit - 2.6.29.6-smp - KDE Desktop

Apr 26, 2010

using Slackware 13 64bit, 2.6.29.6-smp, KDE desktop. i installed the flash-player-plugin using sbopkg. when i try [URL], it says i'm missing the flash plugin. i copied the. so file to

/usr/lib/mozilla/plugins
/usr/lib64/mozilla/plugins

and i still get the same result. what am i doing wrong?

View 11 Replies View Related

Slackware :: Image / Icon Trouble After Slackware-current Upgrade

Jan 22, 2010

I recently upgraded to slackware-current from Slackware 13 via slackroll, and have only encountered one problem. My file manager no longer thumbnails images, and icons (mostly PNG) aren't appearing no matter what GTK theme is set. Running from the command line produces no errors, and when brought up in something else (say feh /path/to/icon.png) it works perfectly. This is the only hitch I have encountered so far. The same thing happens with emoticons in Pidgin. Does anyone know of a fix?

View 5 Replies View Related

Slackware :: Konsole Does Not Recognize Keypad Arrow Keys On Slackware 13.0 / Fix It?

Jan 18, 2010

Konsole does not respond to the following keys on my stand-along usb
keypad:
rightarrow,leftarrow,uparrow,downarrow,home,end,pageup,pagedown

Both of the other terminal emulators on slack do recognize
these keys (xterm and xfce terminal emulator).

I can also confirm that xev, if launched from konsole will recognize
these keys.

Konsole is my terminal emulator of choice and it is really nice to
be able to use my left hand for navigation and command retrieval.

Also, keypad arrows work in X apps.

View 1 Replies View Related

Slackware :: Lack Of Event Sounds In Slackware Builds Of Xfce

Jan 25, 2011

I was over in the Desktop forum yesterday and apparently 'event sounds' are available for Xfce and are part of the original package, but I've never seen them made available, that is, the switch to turn them on isn't where it is suppose to be, in any Slackware specific package of Xfce.I've used 4.61 that came with Slackware64 13.1, 4.61 from the Salix depository, 4.62 from Mr. Workman, 4.62 from 'current' and recently 4.8 from Mr. Workman. None of these make the 'event sounds' available.

View 3 Replies View Related

Slackware :: Lilo Not Booting Slackware Correctly - Errors Inside?

Mar 1, 2010

I'm fairly new to Linux so I'm going to need a step-by-step guide to get me out of this rut. The install of Linux was fine but when I booted up I got this error. VFS: Cannot open root device "302" or unknown-block (3,2) append a correct "root=" boot option;here are the available partitions;

0800 78150744 sda driver:sd
0801 47428608 sda1 <-- this is my Windows partition
0802 30719552 sda2 <-- this is my Linux partition
0b00 1048575 sr0 driver:sr
0b01 1048575 sr1 driver:sr

Kernel panic - not syncing:VFS:Unable to mount root fs on unknown-block (3,2) I guessed from reading this error Lilo isn't pointing to the right partition to boot from? How will I fix this? I read another thread about boot problems on these forums and a guy said to do this:

#mkdir /slacktemp
#mount /dev/device /slacktemp
#chroot /slacktemp
#cd /slacktemp/etc <-- for me it told me that doesn't exist
#vi lilo.conf <-- couldn't do nothing and was frozen
#lilo -v -t -b /dev/device
#lilo -v -b /dev/device

The above solution did not work for me. Can anyone shed a light on a Linux rookie?

View 14 Replies View Related

Slackware :: Good / Easy-to-use Ebook Cataloging - Indexing App To Use In Slackware?

Jun 27, 2010

Which cataloging app would you recommend? I have ebooks in pdf, chm, epub etc. Currently testing tellico. Tags fetching and auto opening the book would be a bonus.

View 2 Replies View Related

Slackware :: Mouse Cursor Is Half Gone And There Is No Toolbar In Slackware 13.1 With XFCE?

Aug 26, 2010

I recently logged into my Slackware 13.1 account and when I issued the "startx" command , there was no toolbar at the bottom and I couldn't see my mouse. I was able to click on a short-cut on my desktop , and my mouse came back. I can't open any thing except VirtualBox. When I open it , the top is cut off , so the minimize , maximize and close buttons are cut-off . I really have no idea what to do.P.S. I have XFCE instead of KDE

View 5 Replies View Related

Slackware :: Dual Boot Of Slackware 13.1 And Windows Server 2008?

Oct 27, 2010

I installed Slackware 13.1 and Windows server 2008, I also installed LILO in MBR, I Found I can boot into slackware, but can't boot into Server 2008. then I use command bootsect/fixmbr. now I can boot into server 2008, but the problem is I can't boot into slackware. I try to install lilo to supper sector. it's not works. I only can boot my slackware by a USB stick.who can help me to solve this problem? I really need these two systems.

View 5 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved