to configure squid as a non-transparent proxy? I understand https cannot be filtered using squid as a transparent proxy. So i need to find out how to configure squid for https filtering.
View 1 RepliesI'm using a Debian box as a gateway. I'm planning on bridging my DLink 604T modem/router so that traffic on the LAN goes to my gateway (which only has one NIC). The Debian box is running a PPPoe application which I'm hoping to log into the ISP through the DLink. I plan to configure the box as a squid transparent proxy. Most Howtos I've seen use NAT with 2 NICs, eth0 for the LAN and eth1 for the Internet. Any step-through to set up NAT for this?
View 4 Replies View RelatedI have set up squid3 and dhcp server on my Ubuntu 10.04 box with IP address of 192.168.0.160. Single network card.Squid runs on port 3148. Everything works fine for the users provided that I set up the proxy details manually on each client pc.I want to set up the Squid to run as a transparent proxy and after reading around I have done the following.In the Squid3 conf file I have entered http_port 3148 transparent.Dropping to Root ( sudo -i )However the transparent proxy does not work and if I enter iptables -L I can see that the rule above has not been retained. The default rules in iptables only show up.
View 5 Replies View RelatedI am trying to install Squid 2.6 as Transparent proxy server.Can anyone provide the step by step configuration details
View 8 Replies View RelatedI have installed and tried both squid version as transparent proxy but they just don't work.
I have eth0 which is where my internet comes in and eth1 which is my local network 192.168.1.0/255.255.255.0.
My default firewall policy is to drop input output and forward, i have already set my firewall to accept and workout the squid and it is working.
Here is the relevant rules i have on my firewall:
Code:
Here is the sample conf i am using for squid:
Code:
Always_direct allow all When using version 2.7.x i was able to make it transparent when i used the below rules:
Code:
I readed the Docs on the squid page but the above rules can't be reproduced to 3.1 and i don't wish to use such rules to make it transparent or hidden so i want some help to figure out why it inst transparent.
I have a squid server set up with two ports:
http_port 3128 transparent
http_port 3129
Port 3128 is set up for transparent proxying (ie, if you send a request to the internet, iptables forwards it to 3128) Port 3129 is just a regular port. If you connect to 3129 directly, you get prompted for a password:
Code:
auth_param basic program /usr/lib/squid3/ncsa_auth /etc/squid/squid.passwd
auth_param basic children 2
auth_param basic realm Squid proxy-caching server
acl password proxy_auth admin
http_access allow password
And this is actually working also. If someone signs then they are able to access unrestricted browsing (with squidguard). However, if they don't, they are transparent-proxied and have restricted browsing. The problem is I keep getting /var/squid/cache.log hits:
Code:
2010/03/03 17:11:04| ACHChecklist::authenticated: authentication not applicable on transparently intercepted requests. Basically evertime there's a transparent request, it throws a warning.
I am using Fedora 9, I have compile the squid with source code, i also deleted the old RPM of squid. i then edited the squid.conf in /usr/local/squid/etc and set http_port 3128 transparent and allowed in my acl to my local network but the transparent proxy is not working. if i remove transparent proxy then squid works fine. when i try to make it transparent the squid access.log file does not show any request coming to it (no activity). i have also forwarded all the incoming traffic to squid port 3128. Can anybody tell me why my transparent proxy is not functional.
View 3 Replies View RelatedI want to make a transparent squid proxy server in centos. The squid proxy version is 2.6 stable. I made a normal squid server but want to make it transparent so that users do not need to enter the proxy settings in web browser. Even i searched about this on google but not getting it properly.I have two lan cards on centos system. ETH1 used for LAN and ETH2 used for WAN. And in this squid.conf i written "http_port 172.16.31.1:3128 transparent" and i also added a rule in iptables which is "iptables -t nat -A PREROUTING -i eth1 -p tcp --dport 80 -j REDIRECT --to-port 3128" but still i have to enter proxy settings at client's web browser to use internet
View 4 Replies View RelatedI would like to install and configure Transparent squid proxy on a gateway server ,but i dont have a local OR intranet DNS server.I am facing issues do that ,regard .My IP series is 192.168.1.1/24
View 5 Replies View Relatedhow to configure transparent proxy in squid-3.0-staple16? I install it with source code
View 1 Replies View Relatedcan anyone give me the solution how to configure dansguardian on squid transparent proxy.i m using
linux - slackware
squid - squid-2.6-stable18
dansguardian - 2.10.1.1
squid transparent proxy is working properly.
what i need, I got two servers for about 4000 users and 300 servers and well the guy never setup dns caching right, so im redoing it. Now my goals
1) DNS cache
2) Transparent Squid Cache only
3) Load Balance - at switchlevel
Upgraded Hardrives to SSD 2x32gb each server 4gb of ram 2x Dell poweredge 850's - p4 2.8 (single cores) So any advise , pointers , expeirnces and best ways to do this being both server will do both dns caching and squid! Also is bind9 the best for this?? i seen stuff about DNSmasq what performs better( i dont need DHCP)
What is the command for installing squid?
Which distribution is needed? linux server?
I am trying to configure squid with Fedora 10 to use it as a transparent proxy webcache.Is there any good tutorial you would recommend to a novice?
View 1 Replies View Relatedi have configured transparent squid with dansguardian for content filtering i used this squid server ip on client gateway(not on browser) for content filtering, is it possible that i could use this squid server in different VLAN.
View 3 Replies View RelatedI am trying to set up a SQUID server on my Red Hat Linux 7.3. to act as a cache server.
The machine has 2 network interface:
eth0 172.30.254.4/23
eth1 172.3.254.65/23
Default gateway is 172.30.254.19/23
The hostname is "amelie".
[Code].....
I am trying to set up squid to make switching proxies easier. I have a laptop which I use at work and at home. At work, I need to connect to the internet via a authenticated proxy. At home, I connect directly to via mobile broadband. So I end up switching proxy settings twice daily, which is just irritating! To solve this I want to set up a system whereby I never have to worry about a proxy - my browser sees a direct internet connection which squid (on my computer) intercepts and forwards either to the mobile broadband connection or to the work proxy (along with the required authentication) depending on which is available. I've read various articles on how to do clever things with iptables and squid, but I don't understand enough of the networking jargon or concepts to know when I need to change to make it work in my situation, or if it is even possible.
View 2 Replies View RelatedHow to make squid proxy transparent?I have configured a Squid proxy server with some ACLs but we have to check from client side whether those ACLs work or not ,I have to open their firefox and manually enter my machine's i.e. proxy server's ip, only after entering this ip , Those ACLs work properly.But now I want to make it work without manually entering the proxy on clients machine.I guess transparent proxy is the solution, but how to configure it/Please guide me and I am one of the machine in LAN.
View 1 Replies View Relatedhttp_port 3128 transparent --> What does this mean? Is this a only thing we do to make Squid Proxy Transparent?
View 2 Replies View Relatedi m using centos 5.6 x86 give us guideline if possible, we have squid transparent proxy, the ip is set 10.0.1.85, this is as gateway we enter in window client pc to browse. now we want to block some website so we try below two method does not work, can you check if anything wrong in this, we enter this all starting of file squid.conf.
View 3 Replies View RelatedI just finished setup a proxy machine that runs in a separate box from gw.
I have the following iptables rule
on squid box
Code:
Code:
Here's an example
Code:
My question is how can i modify the iptables rules so it will forward the real ip's where the requests are originated from.
I'm mon webmaster/developer and I'm new in Linux. Our office suddenly needs to setup a proxy server. Ubuntu Squid proxy server immediately came as an option for us. The question is: does transparent squid proxy configuration using Ubuntu will have no problem with computers running on Windows OS?
View 2 Replies View RelatedI am looking to redesign my network which I'll get into bellow but basically i am looking to setup an transparent/bridged firewall with squid and dansguardian. However, I want to require LDAP authentication to access internet. You'll understand why from diagram below.
My question is, since bridged firewalls operate at layer 2 and have no/require no IP address, can you access higher layered apps with them? Example would be to have the proxy authenticate to LDAP system to check for valid user and valid net permissions, server has to somehow send a reply back, so without an IP, this can't happen right.
Below are two designs I am looking into implementing. Everything Internally will be Authenticated against LDAP with a small possibility of some public servers using LDAP too, but in my way of thinking anything using LDAP would should be behind the router on private link. FYI, the PROXY and the Linux Router would be two physically separate systems. So I guess my second question would be, can systems outside private network access limited internal services securely and be restricted at the same time?
Code:
Option 1:
(TRANSPARENT)
------------ -------------
| CBL MODM | ---------> | PROXY/FW |
------------ -------------
[code]....
I've problem with configuring transparent proxy on Fedora v13 was checking with several examples, last one from here on router (cisco 1812) everything seems ok, think there is a problem with Linux
Squid machine and router 'see each other'
Code:
While try to open web page, on GRE there is:
Code:
But when want to see what hapenning in tunnel between router and squid - there nothing...squid configuration is ok - was checking before try to make it transparent.
Need a bit of help from the linux community. Lately, I have been trying to configure squid as transparent proxy on my server running on RHEL5. I had gone through few articles on web abt how to configure it and configured squid accordingly adding http_accel_xyz settings and then configuring the NAT using iptables. But while restarting squid there were warnings about "unrecognized: http_accel_..." in parseConfigFile.What I could get from these is that probably I need to recompile squid adding transparent proxy support. I downloaded the new squid 3.0 and tried to compile it.But unfortunately, the 'make' command fails giving library errors.I have been stuck with t now as the new squid does not compile and old one does not support the transparent mode.could compile the new one and what supporting libraries do I need to compile it successfully and also from where can
View 7 Replies View RelatedI need to set up an ip table and a transparent squid proxy as followed: I have 3 machine: Machine 1 works as a squid proxy. It has 2 interface eth1 and eth2.
eth1: 192.168.99.2 (Connect to eth1 of machine 2)
eth2: 192.168.98.2 (Connect to eth1 of machine 3)
machine 2 works as a webserver
eth1: 192.168.99.4
machine 3 works as a web client.
eth1: 192.168.98.4
my responsibility is to send all tcp traffic from machine 3 at port 80 to my squid proxy. In order to fulfill the tasks, I have edited the squid.conf as followed: Code: http_access allow localnet http_access allow localhost and in machine 1, I tried 2 ip tables command: Code: iptables -t nat -A PREROUTING -i eth2 -p tcp --dport 80 -j DNAT --to 192.168.99.2:80 iptables -t nat -A PREROUTING -i eth1 -p tcp --dport 80 -j REDIRECT --to-port 80 I don't know if it is right or wrong.
My skill in fedora linux is all acquired by reading online and trial and error. I manage to set up my squid 3.0 proxy server in fedora 11. It is working smoothly as I wanted it to be. I have one client who is running bittorrent that drags all the bandwidth of our network.The problem is I cant make my server work tranparently. I want to make transparent proxy so that it can support my wireless router and I want to control the bandwidth to a fair level for everyone without them knowing.
Please somebody help me configure iptables in step by step, specifically in fedora 11. And all other necessary configuration needed to run my transparent squid 3.0 proxy in fedora 11.I know there's a lot of Linux Genius here that can help. Please help me I needed it badly.
I have a network with two WAN links. One link is supposed to be for Senior Management and the other for the rest of the company. Currently all traffic seems to be going via one WAN link.
Is it possible to setup squid to select the link to use by checking the mac address of the requesting computer
I'm trying to get https/443 traffic go through squid.
View 3 Replies View RelatedI am using Fedora Core 9.0 and Squid Cache: Version 3.0.STABLE2 .
Now i am trying to use the squid as a proxy server but its not working its giving error like this ...
While trying to retrieve the URL: /
The following error was encountered:
Invalid URL Some aspect of the requested URL is incorrect.
Possible problems:
Here is my squid.conf
While trying to retrieve the URL: /
I have also try to forward the traffic coming on 3128 to 80 but its not working: