I've this issue where my audio on the laptop which is toshiba satelite p100 doesn't work after i installed fedora 12. I installed vlc media player but still can't get audio working!! For general info my audio driver is: Audio device: Intel Corporation 82801G (ICH7 Family) High Definition Audio Controller (rev 02)
View 3 RepliesI have a Toshiba Satellite P100-ST9212.reviously it had Windows XP installed and everything worked. Yesterday I installed Ubuntu 10.04 and the installation went smoothly (video, wireless, usb, etc) and I did all the suggested updates. However there is no audio being emitted. All visual and BIOS indications are that the audio should be enabled and working. I have version 4.20 of the BIOSI looked at this forum before submitting this and found general steps to test for.The following steps all succeeded
aplay -l
lspci -v
sudo modprobe snd-hda-intel
The next steps discuss getting fresh ALSA drivers from kernel but this implies that it once worked on a previous Ubuntu install which is not true in my case. So rather than chasing down this potential wild goose I thought I would post this specificestion and see if anyone has seen and better yet knows how to fix this.
Let me preface this by stating that I am a very new Linux user (newb) so I could be missing something very obvious. I have a Toshiba Satellite L645D-S4056 and recently installed Fedora 14 (64-bit GNOME) with all sorts of updates and software. I'm working my way through all of the hardware to get it all running properly. I figured out how to get the RealTek wireless-n adapter working.
The webcam is working even with Skype which is tricky on the 64-bit version. At the moment, my touchpad doesn't work. I see a lot of articles online about the touchpad not double-tapping, but mine doesn't work at all. I've been using a mouse for all my GUI stuff. I went to SYSTEM --> PREFERENCES --> MOUSE and selected the touchpad tab, but I can't figure out how to make it work.
I am a very new Linux user (newb) so I could be missing something very obvious. I have a Toshiba Satellite L645D-S4056 and recently installed Fedora 14 (64-bit GNOME) with all sorts of updates and software.
I'm working my way through all of the hardware to get it all running properly. I figured out how to get the RealTek wireless-n adapter working. The webcam is working even with Skype which is tricky on the 64-bit version.
At the moment, my touchpad doesn't work. I see a lot of articles online about the touchpad not double-tapping, but mine doesn't work at all. I've been using a mouse for all my GUI stuff.
I went to SYSTEM --> PREFERENCES --> MOUSE and selected the touchpad tab, but I can't figure out how to make it work.
I'm trying without success to install 10.10 on a Toshiba Satellite A665 from a USB drive. It will start to boot then gets stuck on:
NET: Registered protocol family 1 I've tried different iso's and different usb drives.Other threads have mentioned that setting acpi=off might work but
1) how do I do that and
2) what else might that effect?
I have problems getting my microphone to work. When I try to record something I just get noise.
The following it he output from /usr/sbin/alsa-info.sh script:
HTML Code:
upload=true&script=true&cardinfo=
!!################################
!!ALSA Information Script v 0.4.58
!!################################
!!Script ran on: Tue Dec 15 10:09:53 UTC 2009 .....
F13: wireless is disabled - running lspci shows a realtek ethernet 8101/8102 - the wired ethernet works fine but not the wireless. Have searched google but they say the realtek drivers should be in the kernel since 2008.are there other commands that can be typed to try to enable the wireless ?
View 5 Replies View RelatedI have Toshiba Satellite L305-S5907 laptop with Microsoft Vista.I tried installing Fedora 9 on my laptop but GUI is not loading on it,system will try to load GUI and showing different colors of lines and screen blinks continously , but desktop is not loading .
Laptop Monitor specification is 15.4� diagonal widescreen TruBrite� TFT LCD display at resolu1280x800 native resolution (WXGA).Except GUI everything is working fine.I tried startx command but then also same scenario is happening. Graphics details: Mobile Intel Graphics Media Accelerator 4500M with 128MB-1759MB dynamically allocated shared graphics memory
I just bought a Toshiba Satellite L650-BT2N23 laptop (i3-core, 4GB RAM) and have Fedora 14 installed on it along with Windows7 64 bit. I am having a hard time getting linux to detect the battery, even when I am running on battery power.
The battery appears as not present and the power management applet always indicates that the laptop is running on AC.
I tried setting acpi=on and acpi=force in grub.conf, but dint make any difference.
Code:
$ uname -a
Linux Eikoh4002 2.6.35.6-45.fc14.x86_64 #1 SMP Mon Oct 18 23:57:44 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux
Code:
$ cat /proc/acpi/battery/BAT1/state
present: no
[Code]....
I recently bought a Toshiba Satellite L650-BT2N23 laptop (i3-core, 4GB RAM) and have Fedora 14 (kernel 2.6.35.6-45.fc14.x86_64) installed on it along with Windows7 64 bit. I am having a hard time getting linux o detect the battery, even when the laptop is running on battery power. The battery appears as not present and the power management applet always indicates that the laptop is running on AC. Setting acpi=on or acpi=force did not remedy the problem, neither did disabling acpi altogether (acpi=off). I have 'Insyde H2O BIOS' version 1.70, which appears to support acpi.
[Code]....
I'm aware of the issues of the ACPI that Toshiba laptops have...
Unfortunately I found out after I bought the laptop.
Auto-boot initiates, and then the screen freezes with this text:
I figured I would begin delving more into the open source environment by dual booting fedora and windows xp pro. Windows xp WAS already installed on the laptop, so I went through the steps to get fedora installed. Everything appeared to be working fine. Fedora came up nicely, and then I tried to boot windows (using grub boot loader). The Windows splash screen appeared, making me think things were fine. But suddenly the screen went black, with the computer going through a restart. This happened every time I tried to boot windows. So I began scouring the web to see if someone had a similar problem. I tried numerous things, but none of them worked. Of them, this appears to have gotten me farther than anything:
Going into grub I changed: rootnoverify (hd0,0)
to: rootnoverify (hd0,1)
Everything else remained the same. When I made this change, the computer went through Ramdisk, and the Toshiba recovery tool. Then two dialog windows appear in secession.
The first stating: Windows cannot find c:inerrordialog.exe
The second stating: Windows cannot find c:inootpriority.exe
I stumbled across information about the recovery console tool. Well, since my laptop has an OEM installation, there is no recovery console tool. But eventually, I was able to find one that I could download. (In case anyone is interested, here is the link for the [URL]
I burned the image to a cd on another computer, and then attempted to boot to the console from the cd/dvd drive on the laptop. But the system crashed, with the customary blue screen. I was hoping to be able to execute the chdsk command to repair whatever damage there might be, but this problem occurs each time I run the image. Fortunately I backed stuff up before this. I'm just hoping that I won't have to go through the ugly process of restoring everything because it's a lot to restore.
I installed Fedora 14 on a Toshiba Satellite L650-18X laptop. The on board speakers work fine but when I try to connect external headphones, the sound still comes from the on board speakers and not from the connected headphones. Also the microphone jack doesn't work.
As I searched the web for possible solutions I think the problem is related to the Alsa sound driver. I kindly ask if someone with experience could share details regarding the Alsa configuration for this particular sound driver in Fedora 14 in order to solve this issue.
For users whom wish to install the wireless driver on the Toshiba Satellite L650-18X, Broadcom offers great information on it's official site
HTML Code: [url]
Here are the steps the user needs to perform in a terminal window in order to install the wireless driver :
I can't get Redhat (Fedora) to mount my usb Flashdrive. My windows O/S has no problem with my usb flashdrive. I can mount my CD Drive and my Floppy drive. My mouse is pluged into one of my usb slots and it works. What am I doing wrong.
View 1 Replies View RelatedSo, help me through getting my audio working properly on my Toshiba Satellite A105-S2081 Laptop. I think I've been through most of the help messages and tried many things to get it working correctly. The ONLY thing that has helped is to go to /etc/modprobe.d/alsa-base.conf and change model=auto to model=generic. (options snd-hda-intel power_save=10 power_save_controller=N model=generic)
I've tried model=toshiba, model=auto, model=lenovo, model=3stack, model=dallas and the laptops internal sound device disappears from the list of sound devices. If I plug in my Logitech Headset, it seems to work fine.It also seems to work fine if I boot it up into XP SP3.It does work now generally with model=generic, but not sure that everything works properly, like the headset & microphone jack. (Actually the reason I have the Logitech Headset is because the headset jack doesn't work).
I have dell B130 with Ubuntu Karmic on it, and I like it. I recently purchased a new laptop, a Toshiba Satellite A505-S6033. I've been trying for about 24 hours to get Ubuntu 10.04 64 bit on this computer, but to no avail. I've seen some people say that they get error messages. When the cd loads up, it comes to the main page (run ubuntu off disk, install ubuntu, check for errors, etc.) Anyway, when I click to run it off the disk, the scren goes blank. The CD spins, but nothing happens from then on. I've tried a 32 bit version of Ubuntu 10.04, but the same thing happens. Just for experimentation, I tried xPud on it, and xpud works fine.
View 5 Replies View RelatedI'm trying to install Ubuntu 10.04 on my Toshiba Satellite Laptop, but when I open the ISO it opens this list of weird variables. It's a command list, and it just freezes. Nothing else.
I'm running Windows 7 with it and want to dual boot.
After installing the intel drivers I noticed a severe improvement to my system performance. I need Compiz now.. and I'll be fully satisfied. Any ideas?
View 2 Replies View Relatedi recently installed ubuntu 11.04 on my toshiba satellite p200-1k8 laptop; with ubuntu the fans were always running at full blast and the laptop would overheat and shut down even though i wasn't using the computer for anything intensive, e.g.just browsing videos. i installed opensuse thinking the problem might have been with ubuntu but in suse as well the fans seem to be running full blast right from start up and the laptop getting quite hot. i've now learnt this is a generic problem with toshiba satellite laptops and linux, something to do with acpi and possibly the ati graphics cards? my gpu is an ati mobility radeon 2600 if thats any help. in windows (which i was last using two days ago) the fans and heat from the laptop were nowhere near this noticeable and i didn't experience this overheating problem just browsing the web.
could anyone recommend any fixes to better the heat management of my laptop on linux (apart from cleaning the fan which i've already tried )?
After updating the repositories, a long update took place... and after completed, my sound card was disabled. I had to reboot the system to have it working again, yet... mp3, mp4, avi files cannot be reproduced at all.
I just want to get rid of Win 7... and I find OpenSuse very stable, solid and friendly. I just installed version 11.2 in this old Toshiba Satellite, as a pilot installation prior the final one in a desktop PC.
I have previous used Ubuntu for a week, literally, on Thinkpad. Now, I got a laptop from my sister which is Toshiba Satelite A135-S4527 with Vista installed.
It's tad annoying for everything, (Why IE and WMP?)
I am thinking about changing to Ubuntu, but I have a few questions. (I don't have much experience with it)
1)I have to install with Desktop Version with 32 bit? (This computer says it's 32 bit, but I am not sure about Desktop Version)
2) I need to use Skype, but when I was using it, the other person can see me, but I was not able to see myself while I can see their face.
3) Which webcam should I get in order to install webcam easily?
4) I only need to use it for -- writing reports, Webcam chat with my family and friends. (AIM & Skype), Ubuntu is fine?
5) Can I type Asian languages - Korean?
I've been trying to figure this out all day, I just got a new Toshiba Satellite E205, and I can't install ubuntu or any other linux os out there that I have tried so far. I've read a lot of things on the forms about changing out the different options but nothing I've tried worked such as graffic safe mode, deleting the quite and whatever the other command was off the end. The closest I've got was when I tried with Debian in text mode I could at least see what was happening, and according to that it can't find my dvd-rom I checked the dev but I can't find it either. So any help what so ever would be appreciated, I really don't want to be stuck with windows 7!BTW, it comes with the following: intel graphics media accelerator HD ACPI x64 DVDRAM ga10f
View 9 Replies View Relatedget the wireless working on my mum's laptop as having to plug it into the router everytime she wants to go online is now becoming an issue for her. I recently upgraded it from 8.04 to 9.04. Ive tried using the Windows Wireless Driver option in System - Admin but to no avail.
Laptop Toshiba Satellite L300D-13D
$ lspci, returns the following
00:00.0 Host bridge: Advanced Micro Devices [AMD] RS780 Host Bridge
00:01.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (int gfx)
00:04.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 0)
00:05.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 1)
00:06.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 2)
00:07.0 PCI bridge: Advanced Micro Devices [AMD] RS780 PCI to PCI bridge (PCIE port 3)
[Code]...
I have recently installed Ubuntu on my Toshiba Satellite A25-S207 Laptop. Everything runs great except that the resolution will not go above 800x600. I had this problem before on the same laptop and was able to fix it but cannot find the fix now (I had to wipe my laptop clean in order to remove some pesky Windows partitions and reinstall Ubuntu) I have found several "fixes" but none work. I tried the one below as well as it applies almost perfectly to my problem
"I just installed the latest ubuntu 10.04 on a Toshiba-Tecra having "Trident Microsystems Cyberblade XP4m32" Monitor. After install resolution is defaulted to 800x600. I followed a method advised in some threads (arount xrandr and cvt) to increase the size (my laptop works with 1024x768 under XP). This was done OK and I obtained the resolution 1024X768 appearing in the drop list resolution options of the Monitor preferences but when I select the option if fails. Alternatively, when I execute $ xrandr --output default --mode 1024x768_60.00 i got the message "xrandr : screen cannot be larger than 800x600 (desired size 1024X76
I also saw a possible fix proposing to add "HorizSync 31.50-48.00" in Xorg.conf but I then I DO NOT have such a file in my /etc/x11/ after ubuntu install (supposing that this will fix my problem !!!)
Boot into recovery mode, when you get to the command line type:
sudo Xorg -configurewhich will create a default /etc/X11/xorg.conf file. Add the lines:
HorizSync 31.0 - 70.0
VertRefresh 40.0 - 75.0to the Monitor section then reboot."
However when I entered the "sudo Xorg -configure" line my computer spit back saying that "sudo" is not an acceptable command
Do I need a certain BIOS for my computer to run Ubuntu? I have a Toshiba Satellite L505. Someone said if I update my bios, it might work. When I try to update my bios, I get an error says something like "The current BIOS settings could not be found" so I called toshiba and they said that Ubuntu might require a certain BIOS.
View 9 Replies View RelatedI'm having a bit of difficulty installing Ubuntu on a Toshiba Sattelite T230 -01Y. Note: if any particulars about this machine are required, I'll be happy to add them. This laptop does not have an optical drive: no DVD, no CD-ROM. I used a USB memory RAM stick (4Gb) upon which I've installed Maverick through System > Administration > Startup Disk Creator. The installation seems to work well. I cut the hard disk (roughly 250 Gb) into 3 partitions: 20 Gb for the system, 2 Gb for Swap, the remainder for /home. The whole setup works as it would on any other PC. Once the setup is complete and the system reboots, it never actually seems to get GDM going. I'm left at a command prompt login. If I leave it long enough (a few seconds), I get a listing that appears over the login prompt, spewing info at me. It sort of resembles the following:
[ 29.296206] rtl8192_SetWirelessMode(), wireless_mode:10, bEnableHT = 1
[ random number] ====>rtl8192_set_chan_()====ch:1
and ch:2, ch:3 to ch:13. Eventually, regardless whether I use the keyboard or not, some kind of screensaver sets in and I can't see any more input-output.If I hit the power button, oddly: the background goes purple displaying CLI characters momentarily, notifying me that the system's going to halt... and the system halts.Any way I can get this going? Do I require the Optical Drive instead of using USB to install the system? I'm afraid all NTFS partitions have been wiped away as the client insisted they wanted nothing to do with Microsoft products.Note: when installing I ask it not to update during the installation as I've had poor results with that. If you feel I should give that a try, I will.
I have a Toshiba Satellite Pro laptop with the following specifications:Proccesor: Intel Core i3 350M / 2.26 GHzRAM: 4GB DDR3Hard Disk: 320GB SATA 5400rpmArchitecture: x86_64The computer has already Windows 7 installed on the C drive whereas there's a D hidden drive with a copy of the recovery image.I'm having trouble to install openSuSE 11.3 as follows:I boot the system with the DVD in its drive. After the welcome screen the process stops
using the typical GUI interface and runs a less graphical one. It is at this point where a
window pops up with a request:"Make sure that CD number 1 is in your drive"I press OK but the window keeps popping up. Frustrated I hit Back and a red window comes up with the message:"No repository found."I cannot go any further than this point
I downloaded and installed OpenSUSE 11.2 but only screen I see is console, SUSE won't even open.I assume that is an error of graphics card (ATI Mobility Radeon HD3650) or Processor (Intel Centrino 2)The error says that there is niether internet connection nor a driver for graphics card.I was able to work the command "startx" while I was using Ubuntu 9.10 (Ubuntu was not able to install proper graphics card driver too)
View 9 Replies View RelatedI have a Toshiba Satellite Pro 4600. Now I can't get the liveCD kernel to boot. I get the first boot menu, but the only thing that works is the Memtest option. If I choose anything else, it will "load kernel" very smoothly to 100%. After that: blank screen with a blinking cursor. In the HCL someone successfully tested this with model with 10.2 and 10.3. I have the 11.2 live CD burned at slow speed. I would expect to see at least some copyright message or anything at all when booting the kernel. I've tried the CD in another computer (desktop, Core2) and it will load everything just fine. I've tried the failsafe and other 'safe' options, no difference. I'm a bit lost here, what could cause it to fail booting at such an early stage ? This laptop has 384MB of RAM and a Trident 16MB graphics card. I'm using it every day, with WinXP so far.
View 5 Replies View RelatedI'm using Ubuntu 10.04 - 64bit install with an A215. The wifi was working fine until today. Ubuntu seems to detect the hardware, and it shows the interface as being 'up', however no networks show up in either the network manager or 'sudo iwlist scan'. I'm not sure if it's a driver issue, or if the hardware itself died.Here is the output of lspci:
ubuntu@ubuntu:~$ lspci
00:00.0 Host bridge: ATI Technologies Inc RS690 Host Bridge
00:01.0 PCI bridge: ATI Technologies Inc RS690 PCI to PCI Bridge (Internal gfx)
[code]...