unning 11.2 on laptop used as stationary desktop. Normally, the backlight turns off after several minutes of inactivity from keyboard/mouse. However, once video played using VLC, the screen simply blanks while backlight stays on, until system restart. Using Totem does not have this effect, but I like VLC.
View 3 RepliesDebian Lenny on a Toshiba Portege 350000:08.0 Bridge: ALi Corporation M7101 Power Management Controller [PMU]01:00.0 VGA compatible controller: Trident Microsystems CyberBlade XPAi1 (rev 82)kernel version 2.6.26-2-686On my system, "xset dpms force off" blanks the screen, but does not turn off the backlight. This means that the automated screen off in X does not actually save any power when it blanks the screen.I can turn off the backlight manually using the BIOS tool "vbetool dpms off" (but then I have to turn it back on again manually too).Question 1: is this a problem with the graphics driver interface, or with X, or with the power management driver interface?Question 2: as a workaround, is there any way for me to hook into the dpms off/on that X is doing, and run a script to call vbetool? The best workaround hack I have come across so far is to have a screensaver that calls vbetool, but I was hoping to find something that doesn't require me to run a daemon all the time.
View 4 Replies View RelatedI have a note HP Pavilion 15-p171nr with Deban Wheezy installed
used X = Gnome (gdm3) in classic view
Hardware:
Code: Select allyaroslav@hpnote:~$ lspci -k | grep -E "VGA|3D"
00:02.0 VGA compatible controller: Intel Corporation Haswell-ULT Integrated Graphics Controller (rev 0b)
0a:00.0 3D controller: NVIDIA Corporation Device 1341 (rev a2)
yaroslav@hpnote:~$
[Code] .....
The problem: backlight is in maximum state and I can not change it.
There are a tons of advices like this:
1 - Open terminal (as a superuser) and type: gksudo gedit /etc/default/grub
2 - In the text file that opens, find the line which says GRUB_CMDLINE_LINUX="" and, inbetween the "", insert the words "acpi_backlight=vendor" (the line will be as follows: GRUB_CMDLINE_LINUX="acpi_backlight=vendor"), save and close the file.
3 - Back again in the terminal session, type: sudo update-grub
4 - Reboot.
It does not work...
Fn + brightness-rightness+ = shows notification about brightness status (50%), but does not control the intensity of backlight. it's just stuck on 50% and that's all.
Ubuntu 10.04 x64,
notebook vaio vgn-nw21mf.
After upgrading to Mythbuntu 10.10 from 9.10 (clean install) on my combined front/backend I cannot get monitor (Dell 3007) to switch off from remote, I have been using simple script to DPMS force off for years with no problems, it still works, but some random time later the backlight comes back on. I have tryed the more complex scripts that stop and start the frontend and all of the acpi_osi options. Disabling screensaver has no effect. what causes this, or how to fix? Sysem is Abit IP35e (I suspect this board is the problem)
[Code]...
I have 2 remote frontends both upgraded OK. I have tryed installing 10.10 on a 'scrap' P4 machine, DPMS off works fine on it. I would try another install and/or another MoBo but its the only TV system in the house now.
i just installed opensuse 11.3 (after being on Mint for couple of years) and really impressed with stability compared to latest Mint 9/Ubuntu10.04.the only issue I have now is I can't turn on desktop effects neither in KDE nor in Gnome.In gnome i can't change compiz seetings at all - the windows freezes after i try to click on 'Enable desktop effects', and that's it. It worked fairly well in ubuntu though.
View 9 Replies View Relatedwhy the bootloader won't show up when I turn on the PC. The only things that come up with search results are 'Why ubuntu isn't on the boatloader' but my problem is is that the boot loader doesn't even SHOW UP.
Installation went completely fine, downloaded a version 10 32-bit iso file and then put in the folder with wibu and it asked me to restart. Restarted the PC, nothing came up so I thought you might have to restart again, restarted again, still no bootloader.
After looking in the 'Add/Remove Programs' of Windows it does say it's installed, so why the bootloader isn't showing up is rather mindbobbling.
I just upgraded from FC10 to FC11 (32-bit) on an old Dell laptop. I set my power management settings (in Gnome) to turn the monitor off after some idle period but always leave the computer running and the hard drives powered. I also set my screen saver to a blank screen. I noticed that the screen saver does come on (turning the screen black), but the monitor back lighting never goes off. I tried different idle times for the power management settings (I usually set it to 1 min, but some other posts implied that 11 mins might work). I should also mention that this is after I've logged into a user account, not sitting at the login screen.
I didn't have this problem in FC10 (the monitor would actually turn off) so I figured it was a bug in FC11, but I can't seem to find a thread addressing this issue. I've found some what similar threads, but none mentioning this particular problem.
i used WUBI to put Ubuntu on an SD card. i ran it off that for a while, and keeping my Vista. then i tried upgrading to to 10.10. there was even a special installer for GRUB in the process.
that's when the problem started. after my comp finished the upgrade, it restarted. but this time, in grub rescue. i tried some of the codes in the wiki, but everything came up unknown command. then someone in the chat told me to use a Live CD and a Super GRUB2 cd.
the LiveCD booted to a screen with a picture of a "keyboard=person with a circle around it". then after a few minutes of just that, lines of text reading:EDD: error 8000 reading sector 3567 EDD: error 8000 reading sector 3577 (and more with consecutive numbers) the Super GRUB2 cd let me get the OS list i usually get from starting up. only Vista would start up without problem. Ubuntu had.. a problem i cant recall right now.
i redid the Live CD, and im back in Ubuntu. i tried the ways of reinstalling GRUB2, as advised by the chats, but nothing seemed to work as described in the reinstallation section of this.
and that is where i stand right now. also, my SD drive's light doesn't turn off now, even when there is no card in it. im kind of worried that when GRUB installed at the 10.10 upgrade, it made that a partisan.
I've installed Debian Wheezy on my HP G62 notebook. In windows the touchpad worked well with all features. But now I can't turn the touchpad on/off by tapping on the LED, which doesn't shines. Also I can't use the double click feature.
View 1 Replies View RelatedI have XFX ATI-HD5670 and use proprietary catalyst 11.2-1 in 64-bit Fedora 14.
I am not sure when this started, or if it ever did work before, but when I started noticing that the screensaver will not turn off the monitor, I set the gnome power manager to make the monitor sleep after an hour.
Now, the display will not turn back on after it has been in sleep mode. I know the system is still running fine as I can ssh from another PC and see that everything seems to be normal, no error message in dmesg, /var/log/Xorg.0.log, etc.
/var/log/Xorg.0.log shows that monitor DPMS is not detected but still enables DPMS:
Is this a problem with catalyst driver? I know it's not the PC or the monitor, because I have a 2nd PC with the same video driver with the same problem, but others without this driver don't (ati open source, nvidia, etc. all work fine.)
I'm wondering if the problem always existed before, but I just didn't notice it because the display sleep mode was never set? If that's the case, my hunch is that it looked like it worked because the monitor was smart enough to turn itself off when the screensaver kicked in and just showed a blank screen, and the video driver was never involved with sleep mode until I set it in gnome power manager, at which point it started showing this problem of not waking up? And because the screensaver was no longer set to blank the screen, but to show some animation, that's why the monitor will never sleep anymore?
i have installed VLC and when i ckuick nothig happens.?
View 1 Replies View RelatedMy card Wifi network doesn't turn on, even at loading configuration of the system is failed. I have to wait a long time until the system itself to load.
And when I write ifconfig or iwconfig is displayed in the console interface wireless card.
And when I come in the panel on the network card, it immediately pops up a window that you can not load the network card modules.
I don't know what could have happened, I do not recall that I recently messed with the system.
Here are the pictures: [URL]....
And here I join dmesg.log file, at the end of a failed: [URL] ....
I have linux mint 17 quiana cinnamon
This is the output when I run it from the console "can't open file '/usr/lib/exaile/exaile.py opensuse 11.3". I'm using opensuse 11.3.
View 4 Replies View RelatedI have a webcam in my monitor (Acer H243HX). It is seen by the system (11.4):
Code:
> kernel - - - [302942.719649] usb 2-5.4: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[code]...
How can I fix the following, borderline irritating issue?
I've tried all of VLCs different Video Output Methods. It didn't use to have this behaviour either, it just began happening now. My taskbar is set to "Always Visible" as I hate "Auto Hide" and I don't want my windows to go above or below it...
I am using Open Suse 11.2 on my HP DV6 notebook. I am connecting my television to the notebook with a HDMI cable and the television is unable to find any signal. Am I missing anything here? Shouldn't it be simply connecting the HDMI cable finding the source channel on the television and then I get sound and picture..
View 3 Replies View RelatedAmarok just skips all songs one by one. It starts playing and ends song immediately and goes to next song.I ran Amarok in konsole..[URL].. I tried different audio files (mp3, wav...) but the same every time.
View 2 Replies View RelatedI see that whenever I try and run a video, the system defaults to try and run it in Banshee.Banshee, though, sits there with a black screen and the information on what it is supposed to be playing. Clicking the Play button does nothing. This includes OGG (OGV?) video files.Does anybody use this feature in Banshee and got it to work?
View 1 Replies View RelatedI have a motherboard p5bvm-se with 82801H (ICH8 Family) HD Audio Controller. The sound in earphones playing. Sound from the microphone is recorded and reproduced in KRecord => microphone is working. ssv:~ # uname -a Linux sslesarev 2.6.31.12-0.1-default #1 SMP 2010-01-27 08:20:11 +0100 x86_64 x86_64 x86_64 GNU/Linux
[code]...
I installed skype skype-2.1.0.81-3.1-x86-64 from build.opensuse.org/home:matteotomasoni or skype-2.1.0.81-suse.i586.rpm from [URL]... Microphone does not work in skype!
When I go into YAST/sound my sound card is shown, and everything works pretty well, however, when I set the volume (other/volume), then exit and come back in, the volume levels are different than when I exited. When I reboot, it sets the master volume to 0%.
View 6 Replies View Relatedmplayer complains about not being able to find libvdpau_nvidia.so. I checked in /usr/lib, and it's there, but it's a link that points to /usr/lib/vdpau libvdpau_nvidia.so. The folder vdpau doesn't exist.
Which package do I need to install to get this to work?
My K3B doesn't seem to recognise a blank CD in the drive tray.
I'm on OS 11.2, K3B & codecs from 11.2 packman, and 11.2 KDE4 factory (ie kde4.4).
When I put a blank cd in, the kde4 device notifier shows me a blank cd and offers to create a project with k3b. I create a data project & click burn, the burn dialog has a greyed out Burn button, and the media selector dropdown says please insert an empty or appendable medium.
If I eject & re-insert the disc at this point, the device notifier again tells me I've inserted a blank cd, k3b's dialog freezes for a second (seems to notice something has happened) but still does not list my cd and remains as it was before.
k3bsetup reports no problems. Burning from commandline (cdrecord) works fine. Dolphin also knows about the blank cd. I've burned to these discs before with no problems (K3B used to work quite recently, perhaps 4 or 5 weeks ago). Updates have been applied in the meantime.
I just upgraded (full reinstall inc. format) from 11.1 (32bit) to 11.3 (64bit).
Everything is working correctly except gmplayer (installed from packman).
If I play movies using gmplayer they do not play smoothly, but the strange thing is if I play the same file with mplayer from a terminal it does play smoothly.
If I play the file from a terminal with gmplayer no errors are reported...
My laptop's internal microphone doesn't work. I ran alsa-info.sh to collect data about my configuration.
Code:
Since the full info dump was a little bit too big to post here, I put the file in its entirety on Pastebin. I also noticed that KMix doesn't display any inputs/outputs...
i just upgraded from Skype 2.0.0.72 to 2.1.047. Now my microphone isn't working anymore and i cannot select it in the skype options. From now on i can only select the PulseAudio server ..
So i have read some howtos for PulseAudio. They say i should starte PulseAudio Volume Control. ok.. Now i should go to the tab "Recording". This tab doesnt exist on my pc. I upgraded to the latest version of this volume control. It still doesnt exist.
I am using OpenSuse 11.0 with KDE4.3
Here are some screenshots:
[URL]
PS: My mic is still working with applications, that dont use pulseaudio.
When logged in as my normal userid to OpenSuse 11.2, I cannot get Banshee to recognize my Creative Zen MP3 player. The player does appear as a device on the desktop and I can access files on the player through that icon, but cannot get Banshee to recognize it so it can be managed in Banshee.If however, I log on as root, Banshee recognizes the device without a problem.
The log file in ~/.config/banshee-1 shows the following:
libusb couldn't open USB device /dev/bus/usb/001/004: Permission denied.
libusb requires write access to USB device nodes.
[code]....
After update to latest phonon (4.4.0-37) - with kde 4.4.1., it doesn't recognize pulseaudio anymore. I am using xine backend, but I can't find 'PulseAudio Server' device entry in phonon configuration
Is there special pulseaudio configuration so phonon will regonize it? code...
I borked my perfectly good 11.2 install, while replacing a failing hard drive. I reinstalled, and now my sound doesn't work - or not quite. I get the left front channel, nothing else. Battle Duel crashes due to sound errors - or I probably wouldn't care.
[Code]....
I have a Gigabyte mainbord with an Intel IHC9 sound chip. When I configure it via YAST the test-sound plays fine, and when I issue:
sudo speaker-test -Dplug:front -c2 -l5 -twav
some friendly voice starts speaking as well.
But:
speaker-test -Dplug:front -c2 -l5 -twav
doesn't bring about anything sound-like.
My settings are stored at:
[URL]