OpenSUSE Hardware :: Can't Save ALSA Configuration
May 10, 2011
I have just installed OpenSuse 11.4 with XFCE environment on my Acer Aspire 5738Z.
Everytime I boot, I need to configure manually the "capture device" with Alsamixer to change it from "micro" to "internal micro".
I tried to save the settings using alsactl store/restore as I do with Ubuntu, but it doesn't work. Every time I restart my computer, the capture is on "micro" again.
Once in a while I stumble on this (after I install something which probably conflicts). I was able with the sticky notes to correct the problem few times but this time is a bit more complicated at least for me.What is strange is that I cannot find the ALSA-Configuration.txt in my system.
I'm not able to reproduce a configuration which I had before.
The plot: openSUSE 11.1 i586, seamonkey 1.1.18, MPlayer dev-SVN-r30099-4.3-openSUSE Linux 11.1 (i686)-Packman = MPlayer-1.0rc2_r30099-1.pm.1.1, mplayerplug-in-3.55+cvs20090923-0.pm.2.2
My old system which died in a catastrophic hardware failure did write the URLs of all movies played with mplayerplug-in to a file located at $HOME/Movies/playlist.
How can I configure the new system to do it again?
I have recently been forced to do a hardware upgrade (my previous mobo died). Now, sounds works ok with,amarok because kde has recognized the new hardware and switched to it.
..... does not work, likely because flash uses alsa-oss which is probably not configured automatically. I have tried uninstalling and reinstalling both alsa-oss and flash, but it didn't solve the problem.
I am using Debian testing. If I install the gnome-desktop-environment then the sound driver defaults to HDA but since I just installed gnome-core (for a more stripped-down version of gnome) the default is the OSS driver. How do I get ALSA to default to the sound driver HDA?
I'm trying to update ALSA, following the instructions here: SDB:Alsa-update - openSUSE.I'm not sure how to proceed at STEP THREE. There are two sets of instructions, based on whether or not the kernel has been updated. I'm not sure if it has been. How can I make sure?
Would like to know the best way (or the pros and cons of different ways) to set up Alsa. I did a search for information on how to setup alsa on my system. I found a lot of out-of-date information even on the alsa wiki. What I did finally locate was two different methods for setup, both seemed somewhat up-to-date. One method at the alsa wiki said to put part of the information in the modprobe directory in a conf file and set up certain aliases. Earlier suggestions for putting information in modprobe.conf or conf.modprobe appear to be outdated and a directory with separate files for each device and a conf extension to the files is currently used. The second method from a thread on the Debian forum said to use alsactl init, set sound levels the way you want and then use alsactl save and restore functionality. Older methods using alsaconf instead of alsactl init appear to be outdated as well. Not sure where to put the call to alsactl restore though. Didn't notice that in the documentation.In case it matters, I'm running Debian Stable and have a built-in sound card on the motherboard with AC97 compatibility. It's a Realtek ALC882.
Is there a preferred or better method for setting up alsa? Is there a good pointer to instructions that are not out-of-date somewhere? Would be very interested to hear how others set sound up on their machines. What do others recommend as best steps to do this?
Alsa is currently using my HDMI port to play sounds through using card0 "ATI R6xx HDMI". I'm on a laptop and I want to be able to use my laptop speakers and headphone jack so how do I set alsa to use card1 which is "Conexant CX20582"?
I install the ATI drivers yesterday and today I've realised that it broke my sound. I have a HDA nVidia sound card built in (with a Realtek chip), but when I run alsaconf, it doesn't find it. It tries to use either the ATI HDMI audio port or a legacy generic driver. Any hints as to how I can fix this?
I know very little about Debian but have an ASUS T100TA tablet which runs fairly well under Debian 8 Jessie (kernel 3.16.0-4-686-pae). I used the following guide successfully to activate the wireless but am having trouble with the audio section of it.URL...
First, I went here and downloaded the file called 'NEW T100_B.state'.URL....
Then I copied it to /var/lib/alsa/asound.state and ran 'alsactl restore' which reported that i had no soundcards.I then downloaded and expanded linux-firmware-master-intel.tar.gz but am not sure what to do with these files. I copied them to /lib/modules/3.16.0-4-686-pae/kernel/drivers/firmware as they are specific for this kernel, but they don't seem to be doing anything and 'alsactl restore' still tells me that I don't have a soundcard. What do I need to do with these files?
I followed this doc for the "debian method" for building the kernel: [URL]. I installed the source in /var/tmp/src/linux-2.6-2.6.32 , configured it, and tried make-kpkg modules-image. The error I get is:
checking for current directory... /usr/src/modules/alsa-driver checking cross compile... checking for directory with ALSA kernel sources... ../alsa-kmirror checking for directory with kernel top-level makefile... /var/tmp/src/linux-2.6-2.6.32 checking for directory with kernel headers... failed make[2]: *** [configure-stamp] Error 1 make[2]: Leaving directory `/usr/src/modules/alsa-driver' make[1]: *** [kdist_image] Error 2 make[1]: Leaving directory `/usr/src/modules/alsa-driver' Module /usr/src/modules/alsa-driver failed.
I tried some hacks such as setting KBUILD_SRC or ln -s linux-headers-2.6.32-5-amd64/ /usr/src/linux - but these fail too.
how to install alsa drivers along with Asus xonar dgx sound card. I followed these instructions. URL....And until "Setting up modprobe and kmod support" instructions were clear. I should put something in /etc/modules, but I dont down exactly what.
Code: Select allroot@SERVER:~# aplay -lL; **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: ALC887-VD Analog [ALC887-VD Analog] Subdevices: 1/1 Subdevice #0: subdevice #0
Code: Select allroot@SERVER:~# lspci -nn | grep -i audio; 00:1b.0 Audio device [0403]: Intel Corporation 6 Series/C200 Series Chipset Family High Definition Audio Controller [8086:1c20] (rev 05) 02:04.0 Multimedia audio controller [0401]: C-Media Electronics Inc CMI8788 [Oxygen HD Audio] [13f6:8788]
I've customized my ubuntu setup using many themes and icon packs and now have it just the way I like it but every time I create a new user account it resets to the default interface. Is there any way to save the current configuration I have (theme, icons etc.) as default?
I run ubuntu 9.10 and i've set up my drivers/music player/themes/browser etc just the way i like them. However I now want to install XP and dual-boot. My hard drive is not partitoned, so I want to ask if there is a way to save my setup to use after installing XP.
Original tittle, edited for add the tag [SOLVED] on subject How can I save the configuration of panel of the xfce4 ?
I have a pretty panel configured on my xfce4 (debian lenny). How can I save the configuration of my panel ? I'm afraid to lost my configuration in some situation of error.
All routing settings made with the ip tool (route command) are lost when the redhat server reboots.How to save routing information to a configuration file?
I recently reinstalled Lenny and I am attempting to save my /home directory. I used the graphical install and when it came to the part about partitioning, I created a new /home partition "hdb1" and told the installer to ignore my old /home partition "/dev/hda9".Following the completion of the install, I logged in and changed my /etc/fstab so that /home --> my old /home partition "/dev/hda9". I then mounted the old partition to /home and rebooted the system. Now, when I go to my /home directory >> properties, I can see that the files I had are on the drive (2GB are used) --- but --- I cannot actually see the files??
For some reason my sound stops working in KDE4. I can't trace it to any particular event, it seems to happen randomly. I think the problem started when I tried installing ktts (the text to speech engine) but I cannot be sure. I've now removed ktts but my problem persists.The strange thing is that if I go to the sound configuration in yast and play the test sound it works fine. But if I try play the test sound in multimedia settings from within systemsettings then I get an error saying "The audio playback device HDA Intel (AD198x Analog) does not work." Also that error message window is titled phonon.
I didn't install phonon but notice that it's installed. I assume it was installed with the default install because trying to remove it brings up over a 100 dependencies.The left speaker / right speak test from the konsole works but only as su and not as me. I get permission errors. Is that normal?
Code:
speaker-test -c2 -l5 -twav speaker-test 1.0.21 Playback device is default Stream parameters are 48000Hz, S16_LE, 2 channels
[code]....
I also notice that sometimes when I boot up, after I login at the graphic login screen it kicks me out to the command prompt asking me to log in again. When I log in and "startx" KDE starts up but without sound and no kmix. Trying to start kmix manually doesn't start it. I just get an empty window.Again the sound works from the yast sound test.I've tried removing the kmix config files from /.kde4/config/ but that doesn't help. The logs don't show anything obvious to me and the problem appears to occur randomly in so much I haven't been able to figure out what triggers it yet.I also noticed during a session that I have this sound problem and after I've fixed it by resetting the sound card in yast that kde doesn't shutdown when trying to shut the laptop down.
I get the kde logging off chime but the desktop remains and is fully functional. After that any attempt to log-off or shutdowm is ignored. I'm forced to run the shutdown command from the konsole to shut the laptop down. I'm not sure how it's related but it only happens after the sound problem occurs. I'm using KDE4.4.1 but this started in KDE4.4.0 so the update didn't help any. When I upgraded to KDE4.4.0 I started with a fresh .kde4 directory.
1. I run Suse 11.2 with two sound cards , one HDA comes with motherboard and second is USB, which I use for skype and talking. In YAST everything is fine the motherboard card is marked as prime card and the usb card is marked as second. But often when I log in alsa decides that second card is main and I have to pull out the USB card, run command "rcalsasound restart" and put the USB back afterward. It is a way that to be fixed in the way that alsa remember my choices forever. 2. The other problem is that from time to time the sound suddenly dies and I have to bring it up with rcalsasound restart again.
But I have to admit that their significant improvement with managing sound with PulseAudio.
I've got sound - I hear all the system sounds, I can play sound files, CDs, etc. But I have not been able to record and play back anything with success.
Originally, when I would record (either with arecord or with audacity) I would get extremely low quality sound, with lots of noise and crackling, and my recorded voice was barely audible (even with volume turned up to max). I played with alsamixer for hours without being able to improve matters.
Things are worse now. I tried installing alsa-firmware, as indicated at SDB:Audio troubleshooting - openSUSE. I also tried updating alsa following instructions given at SDB:Alsa-update - openSUSE. I'm not sure which of these changes did it, but the result is that I can no longer record ANYTHING at all. I get absolutely nothing, not even the low quality noise and crackling I was getting before. It's as if there is no audio input at all.
Uninstalling alsa-firmware and reverting back to the older alsa version (1.0.20) didn't change a thing.
I'm running openSUSE 11.2, kernel 2.6.31.14-0.6-desktop, alsa 1.0.20. My sound card is a Creative X-Fi (by the way, yast cannot detect my card, another problem I have never solved).
I have stated that I use Pulse because ALSA fails to utilize more then one sound app. With ALSA if I watch a ..... vid in firerfox and soon open my music player the music player wont work unless I close off firefox. so I close off firefox but sometimes flash hangs the sound device hostage and I have to log out or kill something to make sure ALSA is freed up. So this is why I use pulse, it makes using more then one sound app at a time much easier, no hang ups at all. But there are a few apps that dont get along with pulse so there must be a way to configure alsa to use more then one sound app at a time. Do I have some compiling to do? Is it commandline? I am just curious what you anti pulse folks do to use more then one sound app at a time without the aid of pulse. it only mumbles about the differences between the multiple sound servers.
I have just installed OS 11.3 onto a lenovo desktop / Thinkcentre that previously had vista installed on it. With Opensuse I am having trouble getting much sound volume. With Vista the volume was fine but with Opensuse I have PCM, Master running pretty much on full. This gives me a respectable volume but I think there should really be more left in the tank from what I have it at. Is there any way to increase the gain in Alsa? The sound device shows in KDE as HDA Intel (AD198x) using xine backend.
I have some microphone problems. I can't record anything. (I'm using openSUSE 11.3)
My sound card was detected almost correctly (at least the chip-set was i think). I have an Asrock motherboard (k7upgrade880, with a Southbridge: VIA 8237 | Audio: CMedia CMI9761 6 channel AC'97.
I ran these commands so far with these results - while i was following the audio troubleshooting guide (SDB:Audio troubleshooting - openSUSE
But i have NO audio playback problems - movies, games, music all play well. And the Microphone guid has a broken link
I tried to change my 50-sound.conf file (i read it on a forum, I'm new to linux troubleshooting) from this: options snd slots=snd-via82xx to this: options snd slots=snd-via82xx position_fix=1
But that did not work either. I did not get any sound with the last line.