Hardware :: Install CentOS With Hardware Raid In HP Proliant DL165 G7
Jun 26, 2011
I need to install centOS 5.6 64bits in a server HP Proliant DL 165 G7, with four SAS hard disk, a controller array, 32Gb RAM and two processors... I have some experience creating software raid but it's first time i try to install a hardware raid.
For the moment, i began editing the option RAID into the bios and after that create a RAID 10, but now... What steps have i to follow to install centOS? CentOS installer recognize me the raid or have i to install some kind of driver in the beginning to installation process?
note: I found some diskettes from HP, but im not sure if that works to me: [URL]
View 5 Replies
ADVERTISEMENT
Aug 1, 2009
how to setup RAID on a Compaq Proliant DL580 G1 Server. Currently there is no OS installed. I used the SmartStart CD but there is no option to setup RAID. When I put in the boot CD for CentOS 5 it recognizes individual hard drives not a RAID Setup.
View 4 Replies
View Related
Feb 5, 2010
I forced my workplace to forgo windows and opt for linux for web and mail server. I'm setting up Centos 5.4 on it and I ran into a problem. The server machine is a HP Proliant DL120 G5 (quad core processor, 4GB Ram, two SATA drives, 150GB each attached to the hardware RAID Controller on board). RAID is enabled in the BIOS.I pop in the Centos disk and go through the installation process.
When I get to the stage where I partition my hard drive,it is showing one hard drive, not as traditional sda.but as mapper/ddf1_4035305a86a354a45.I looked around and figured that I need to give Centos the raid drivers. I downloaded it from:
[URL]
I follow the instructions and download the aarahci-1.4.17015-1.rhel5.i686.dd.gz file and unzipped it using gunzip. Then on another nix system, i do this:
dd if=aarahci-1.4.17015-1.rhel5.i686.dd of=/dev/sdb bs=1440k Note that I am using a usb floppy drive, hence the sdb. After that, during centos setup, i type: linux updates dd
It asks me where the driver is located. I tell it and the installation continues in the graphical mode. But I still get mapper/ddf1_4035305a86.a354a45 as my drive. I tried to continue to install centos on it. It was successfull but when i do a "df -h" it gives me /dev/mapper/ddf1_4035305a86......a354a45p1 as /boot
/dev/mapper/ddf1_4035305a86......a354a45p2 as /
/dev/mapper/ddf1_4035305a86......a354a45p3 as /var
/dev/mapper/ddf1_4035305a86......a354a45p4 as /external
/dev/mapper/ddf1_4035305a86......a354a45p5 as /swap
/dev/mapper/ddf1_4035305a86......a354a45p6 as /home
Well i know why it's giving these, because i set it up that way, but i was hoping it would somehow change to the normal /dev/sda, /dev/sdb. That means that the driver i provided did not work. I have another IBM server (5U) with raid scsi drive and it shows the usual /dev/sda. It also has hardware raid. So i know that there is something wrong with the /dev/mapper/ddf1_4035305a86......a354a45p1 format.
First, is there any way that I can put the aarahci-1.4.17015-1.rhel5.i686.dd (floppy image) on a CD?. I really need to set this up with raid. I know i could simply disable raid in bios and then i would get two normal hard drives sda and sdb. But it has to be a raid setup. Any way to slipstream the driver into the centos dvd? The hp link i provided above, under installation instructions, there are some instructions titled "Important". But I couldn't get it to work.
View 2 Replies
View Related
Mar 23, 2010
I have successfully installed CentOS 5.4, and after choosing it from the GRUB menu, I am getting the following error message:1706-Smart Array Controller Extended BIOS Data Area Memory Corrupted. Int 13h BIOS Cannot Continue - System Halted.I'm using two SAS disks that came along with the server, left the default RAID configuration (1+0) on a P410 controller
View 5 Replies
View Related
May 13, 2010
im the newbie in this area.can anyone tell me how to install centos 5.4 in this hp proliant dl160 server.what I need to do to handle this RAID thing? because it show me not detected any logical hard drive in RAID configuration utility.
View 5 Replies
View Related
Aug 28, 2010
I'm trying to install centos 5.4 on a older compaq proliant 6500 server with raid it was previously used for windows server 2003 for several years but management wants it turned into a time clock server that will run linux, obviously there is no smart start software for centos on this model, is there some kind of driver needed, be aware that i only did installations on single drive servers and new servers that take centos right away with new raid adapters compaq raid controller 3200.
View 10 Replies
View Related
May 17, 2010
I have a problem installing Ubuntu on an HP Proliant ML115. This server has a 1TB mirrored RAID setup (and 1 250GB drive), problem is, Ubuntu apparently doesnt like it, it detects the RAID but fails to partition the hard drives and the installation cant continue. I tried the guided partitioning using the whole disk (detected RAID array). Here is what syslog gives me:
May 17 22:32:30 main-menu[504]: INFO: Menu item 'disk-detect' selected
May 17 22:32:30 net/hw-detect.hotplug: Detected hotpluggable network interface eth0
May 17 22:32:30 net/hw-detect.hotplug: Detected hotpluggable network interface lo
May 17 22:32:31 hw-detect: Loading PCMCIA bridge driver module: i82365
May 17 22:32:31 hw-detect: FATAL: Module i82365 not found.
[Code]...
PS: Im very noob regarding this kind of stuff so detailed instructions please, also feel free to give configuration tips
View 6 Replies
View Related
Jun 7, 2010
I'm having a great deal of time getting Lucid Server up and running on my Compaq Proliant ML330 G2. I've put a thread up in installing and upgrading, but people there don't seem to have any ideas about my problem. Since I figured there would be a higher concentration of server users here,
I've got a Proliant ML330 G2, 2 1.4 GHz PIV's
A dvd and CD drive on IDE1 (I'll explain why in a moment
A 65 gb hdd on IDE2
and four 40gb hdd's on hardware ide raid.
I've tried everything, but I can't get the sucker to boot. Installing to the raid array doesn't work. Some array setups won't partition, and others aren't even recognized as arrays. I've tried disabling the raid array and installing to the IDE hdd (my original intention) but I just get bad system disk errors. It would be exceptionally helpful if anyone has one of these boxes, or has worked on one, but I'm willing to take advice from any direction at this point.
View 3 Replies
View Related
Feb 26, 2010
Installation CentOS 5.3 on server HP Proliant ML110 passes without problems. At installation I choose breakdown of disks by default.All is established without problems. After reboot HP stops. Last message on the screen the such:
Filesystem type is ext2fs, partition type 0x83 kernel /vmlinuz-2.6.18-92.el5 ro root=/dev/VolGroup00/LogVol00 rhgb gniet
[Linux-bzImage, Setup=0x1e00,size=0x1b7034]
initrd/initrd-2.6.18-92.el5.img
[Linux-initrd@ 0x37cf5000,0x2fa44c bytes]
Further loading does not go. It is probably connected with RAID a file? On HP it is adjusted hardware SATA RAID1 Embedded. In what a problem?
View 2 Replies
View Related
May 10, 2011
I have DELL R310 server with PERC 200H controller and RAID 5 configured already.This is my first time I want to install CentOS and seems like a new challenge for me I've read some articles on Wiki and posts on this forum and didn't find any information how to install CentOS on RAID 5.I only noticed that if there is fake or software RAID1 it should be switched off and made by OS configuration.I think PERC 200H is separate controller so RAID 5 is hardware RAID, is there anybody who can confirm ?My problem is that when I try to install CentOS it doesn't see any hard disks ... I looked for drivers on DELL web site and there is driver for Red Hat 6. I tried to install it using linux dd command but it doesn't recognize. Is there anybody else who met such problem ?
View 3 Replies
View Related
Jan 19, 2010
I have a proliant dl120 server, with centos 5.4 and I want to monitoring the temperature and fault of the server but the software of hp seems don't work. I have tried to install lm-sensor follow this guide [URL] but the result is:
[root@serverhost bus]# yum install lm_sensors
Loaded plugins: fastestmirror
Loading mirror speeds from cached hostfile
* addons: centos.intergenia.de
* base: centos.xengage.it
* extras: centos.xengage.it
* updates: centos.intergenia.de
Setting up Install Process
Package lm_sensors-2.10.7-4.el5.x86_64 already installed and latest version
Package lm_sensors-2.10.7-4.el5.i386 already installed and latest version
Nothing to do
[root@serverhost bus]# sensors-detect
# sensors-detect revision 5291 (2008-06-23 23:40:46 -0700) .....
View 2 Replies
View Related
Mar 11, 2009
I have just installed Centos 5 on my HP Proliant ML110 G5 Server. At the install time it could not detect my DVD-ROM drive so I installed it using FTP hoping that it will make it work after installation but nope. My system is running but I cannot see ant DVD-ROM drive on my system.
It's really critical, I have lots of software to install from DVDs and actually I am relying on a shared DVD-ROM drive from another machine and it's quite slowing me.
View 4 Replies
View Related
May 12, 2011
I'm installing Centos 5.5 on a HP ProLiant DL180 Server with ~8 TB of hard disk (4 disks that have been pre-RAIDED), from an installation DVD.
Normally when I get to the partitions screen, I would select "remove all partitions etc".
But this gives me an error message "Your boot partition is on a disk using the GPT partition scheme but this machine cannot boot using GPT. This can happen if there is not enough space on your drives for the installation."
Pressed OK, tried the other three partition options but they led to the same outcome.
Tried Advanced storage configuration: Showed that there was one hard drive (c0d0) with ~ 8 TB of space.
I figured I should create a root sector, set one up with 100 MB of space, ext3, set the mount point as /.
Created a software raid of the remaining space.
Trying to go "next" gave me a similar error about GPT partition scheme. Trying various other configurations all gave similar errors about the GPT scheme.
What do I need to do? Some earlier hard format of the disk or something?
View 5 Replies
View Related
Aug 5, 2009
I just updated CentOS 5 to latest kernel 2.6.18-128.2.1, but after reboot the new kernel crashes...If I witch to 2.6.18-92 kernel it works...
View 3 Replies
View Related
Feb 28, 2009
I am attempting to set up an IBM Intellistation Z Pro to optionally boot from many OS versions. One of these is Windows XP. Windows XP is currently installed on a RAID 1 device consisting of a pair of 1 GB WD drives. These are SATA drives. The HBA I'm using is a SYBA SATA II card that uses Silicon Image's SIL3124-2 chip. The card has a BIOS and I've set up two 60 GB mirrors for Windows. I boot XP fine from this setup and things run good.
I've downloaded the CentOS 5.2 images and am able to start the installation process. I'm baffled on where to install the OS software on the RAID device. The installation process shows the two 1GB drives as separate drives and there is no acknowledgment of the 60 GB partition I've already created on them for Windows XP. I expected to see only the one logical RAID device and 60 GB of it in use for a NTFS partition. Reluctant to proceed further, I bailed on the install and am asking for advice on how to proceed.
The big question is
1) How can I install CentOS 5.2 on the RAID drive to coexist with a Windows XP installation? My desire is to boot either from this drive.
other questions related to this are:
2) Why does the CentOS partitioning software used for the install not display the logical RAID drive set up through BIOS (I'm assuming that this means it was set up apart from any Windows drivers etc.)? Only the two physical drives are displayed and there is no mention of any partitions in use.
View 3 Replies
View Related
Feb 4, 2010
I am trying to setup a H/W RAID-1 matrix but I am unsuccessful. I am trying to get partitions installed as /dev/md0, /dev/md1 but it keeps going for /dev/mapper/isw...The reason is that I have R1Soft backup and it needs to hook the partitions as seen in /proc/partitions from /dev not /dev/mapper/isw. I have tried to boot the installation with various options but nothing!
View 16 Replies
View Related
Sep 22, 2010
Im trying to install CACTI EZ on a HP Proliant Blade 460c G6. But im having problem with detecting the hard disk. CACTI EZ installation has the drivers for this and loads the driver itself. But when it now detects for the drive, it has the error "Drive not Found".Do you have bootable CD (iso image) that can load the drivers for Cent OS 5 for HP Proliant Blade 460c G6 server.
View 1 Replies
View Related
Feb 3, 2011
I have got a server which has a motherboard with nvidia mediashield raid built in, with Centos installed it picked up the raid 5 array that i had configured as one drive so the os install was straight forward. When i booted the netinstaller of opensuse 11.3 run though the setup, when getting to the partition setup is was picking up the three hdd as seperate drives and not one, so i got to a certain point and aborted the installation and i re run the installer, the raid status said the array was degarded or something which i knew there was nothing wrong with it as i had set it up only about 2 weeks ago and there was one drive missing aswell. So i removed the array and re configured the array and rebooted and the raid status said healthy again as it was before on centos, then i run the opensuse installer again and it went though the process again but completely stop at "Searching for linux partitions" , cursor was working fine , but nothing else was so i had to press reset.
This was my problem, i know kind of what the problem is, but what i want to know is , i thought opensuse is based on rhel same as centos but how comes centos has the drivers for the raid chip i have in my board and opensuse has not.
View 5 Replies
View Related
Aug 3, 2010
I am trying to connect a RAID Box to the server via LSI 8880EM2 RAID controller.The raid box is FUjitsu Externus DX60 with raid 1 configured.The server is Fujitsu Primergy SX300 S5 with LSI 8880EM2 RAID card.The external raid box is being recognised by the raid controllers bios.
The server runs CentOS 5.5 64bit. I have installed the megaraid_sas driver from LSI website and MegaCLI utility but CentOS still fails to see the box.MegaCLI utility, when launched from CentOS, recognises the raid box, CentOS does not(no mapping being created in /dev).
I have also tried to create a logical RAID0 HDD on one physical HDD(as seen by MegaCLI) with MegaCLI utility in CentOS.The result was success and the new logical drive could have been used, but when restarting the server, the controllers' bios fails with an error (not surprised(one logical RAID0 on one physical HDD)) and configuration is being erased.
Has anyone tried connecting 8880EM2 controller to a raid box with raid configured on the box, running it all under CentOS and what were the results.
View 3 Replies
View Related
Jul 27, 2009
Currently I am attempting to install Centos 5.2 64bit onto a Supermicro X7DCL-3 motherboard based machine. The Raid recognizes the HDD that's been installed into it, however, the drivers for the raid are not included in the install. After contacting Supermicro I've been supplied with a driver package that should fix the problem.[URL]However, I am still having trouble using the package in order to find the HDD (The only HDD in the machine) that is on the raid.I think I'm doing something that's should be fairly simple, but am screwing it up pretty bad.
View 1 Replies
View Related
Oct 23, 2009
I had a fedora 11 on a IDE HDD and a raid 5 with 4 SATA HDD with a rocketraid card 1640 After a crash of my HDD, i try too install a centos 5 on a new HDD and the problem is to install a raid 5 without loosing my datas who are on the raid.
View 1 Replies
View Related
Nov 6, 2009
I am trying to install Centos 5.3 x64_64 on old DELL server
PE 2850 with RAID 1 & 5 voluomes ON PERC 4/DC DUAL CHANNEL RAID CARD
Install can not see Raid Volumes
The server can still boot with the old OS RH EL 2x and RAID and Raid volumes are fine
View 6 Replies
View Related
Feb 10, 2010
I am trying to get a understanding of how to install a RAID 1 on a Dell Power Edge server.
HARDWARE:
2 - 16gig SCSI dives
1 - 36gig SCSI drive
I have read through some documentation found online and at centos.org but still having problems.
get this accomplished keeping in mind this is my first go at using RAID system.
View 4 Replies
View Related
Oct 4, 2010
I am trying to install Centos onto a Poweredge 2650, with Dell Poweredge Expandable Raid Controller. I have 5 SCSI disks installed, and have created and initialised 2 logical volumes via the SCSI controller setup utility (Ctrl M after boot). After reboot the system reports two logical volumes present.
The Centos installer cannot find any disks when it gets to the disk partitioning/setup step. It reports no disks present. Do I need a specific driver for this controller?
View 2 Replies
View Related
Feb 28, 2011
If I have a windows installed in raid-0, then install virtualbox and install all my linux os,s to virtualbox will they be a raid-0 install without needing to install raid drivers?
View 1 Replies
View Related
Dec 10, 2009
I am going to be using CentOs 5.4 for a home storage server. It will be RAID6 on 6 x 1TB drives. I plan on using an external enclosure which is connected via two SFF-8088 cables (4 drives a piece). I am looking to try and find a non-RAID HBA which would support this external enclosure and allow to use standard linux software raid.
If this is not an option, I'd consider using a hardware based raid card, but they are very expensive. The Adaptec 5085 is one option but is almost $800. If that is what I need for this thing to be solid then that is fine, I will spend the money but I am thinking that software raid may be the way to go.
View 3 Replies
View Related
Jan 8, 2010
I have One Server HP proliant Ml150 G5 with ARRAY Controller and I want to INSTALL REDHAT9 But OS When I install REDHAT9 IT gives NO hard disk Found ON HP SITE there is no driver for array controller for REDHAT9
View 5 Replies
View Related
Sep 26, 2010
I try to install linux Slakware 8.0 on HP Proliant 350ML server. I can boot from the CD but then anytime I do fdisk /dev/sda I see a message that the hard drive cannot be accessed. Is there anyting I can do to secceed?
View 11 Replies
View Related
Apr 18, 2011
I recently purchased HP Proliant Microserver with the idea of having it as a home server running Amahi. I added one 2TB hard disk to the already installed 250 GB drive. The Microserver has no cd/dvd drive so I created a bootable pen drive using LiveUSB Creator tool from Fedora 14 installation DVD iso image. However, I ran into problems in the very first phase though I struggled hard, juggling i386, x64, Live images...
Now, for i386 Fedora: The machine successfully boots from the pen drive but after selecting language and keyboard, the installer does not see the installation image - or even the pen drive at all - saying "No driver found". Then, I can only open "Select Device Driver to Load" (screenshot) where I can only see whole bunch of drivers I have no idea which of to select. I tried "USB mass storage driver for Linux", nothing happened, I'm returned back to "No driver found". Haven't found the "HP NC107i PCI-Express Gigabit Ethernet Server Adapter" driver in the list...
x64 Fedora: Same result, though x64 at least recognizes the HDDs that are already in the box (screenshot) so I can try to use image files unpacked on the second one (ext4 formatted). Then, the installation proceeds till the point of formatting the installation drive when it suddenly "Cannot find ISO 9660 image" (screenshot) and I cannot but Exit.
Live x64 image: I tried the Live bootable image from the same pen drive - it booted and installed correctly and at the first glance the system was working fine, connecting to the internet, downloading updates etc. However, this is not my option because I didn't have the option to add additional Repository during the installation from Live image (as it is in this guide, search the page for "Add the Amahi repository"). why the installation is not working in my setup?
View 3 Replies
View Related
Jan 26, 2010
try to install opensuse 11.2 on HP ProLiant DL160 G6 Server ? i want to know if it's compatible with this server.
View 8 Replies
View Related
