I have a spare machine running Windows 7 Pro x64 in RAID 0 (software RAID). I would like to install Fedora 13 x64 on a dedicated SATA HD (non-RAID) already in the machine but I'm unsure how Fedora's boot-loader will react to the RAID 0.
View 14 Replies
I have a system with RAid 0 with Windows 7. I want to load Ubuntu on a stand alone disk. I have two disks obviously for my raid o, two storage disks and an extra disk for ubuntu. I have tired to install unbuntu but upon start up I get an error on the disk. I than had to use grub to repair my mbr. My question is how do I make this work where I can have a dual boot system. I have been running ubuntu on my laptop .
View 2 Replies View RelatedI have recently bought a new computer, and would like to take my existing RAID-1 from the old computer to the new computer, as the disks hold many digital photos. The old RAID-1 was in a DELL XPS 400 (and based on the intel 82801GR chip I guess), and the new computer has an intel ICH10R. I understand that both chips require a Windows driver if RAID-1 is needed.
The old disks still reside in the "dead" computer. How can I proceed? I hope the solution is that fakeRAID can be enabled, but I would like to ask the clever and experienced community before I do something that cannot be undone (and maybe lose all my digital photos!). Or maybe you have a better solution?
If you need more information to help me then please tell me to post information; I do not really know much about setting up RAID-1.
Currently I have windows 7 x64 installed on a pair of raided ssd's using an x58 motherboard(ich10r) and I want to duel boot ubuntu x64 (either 9.10 or 10.04) on another harddrive (not part of the raided ssd's). Does anyone know if this can be done? I haven't found anything out there about this. I have tried to install Ubuntu from the CD. It gets to the install screen booting from the CD, but it doesn't let me install or try Ubuntu. I hit enter and nothing happens. I can look through all of the options but can't install or boot into Ubuntu.
View 1 Replies View Related(This is for a 100% Clean install)
Q1) I was wondering if it is possible to Dual boot Ubuntu with Windows XP on a 1TB RAID-0 setup ?
Q2) Also, is it possible to create a SWAP partition (for Ubuntu) on a NON RAID-0 HDD ?
Q3) Lastly... I read GRUB2 is the default boot manager... should I use that, or GRUB / Lio ?
I have a total of 3 HDDs on this system:
-- 2x 500GB WDD HDDs (non-advanced format) ... RAID-0 setup
-- 1x 320GB WDD HDD (non RAID setup)
(The non RAID HDD is intended to be a SWAP drive for both XP and Ubuntu = 2 partitions)
I plan on making multiple partitions... and reserve partition space for Ubuntu (of course).
I have the latest version of the LiveCD created already.
Q4) Do I need the Alternate CD for this setup?
I plan on installing XP before Ubuntu.
This is my 1st time dual booting XP with Ubuntu.
I'm using these as my resources:
- [url]
- [url]
Q5) Anything else I should be aware of (possible issues during install)?
Q6) Lastly... is there anything like the AHCI (advanced host controller interface) like in Windows for Ubuntu?
(Since I need a special floppy during Windows Install...) I want to be able to use the Advanced Queuing capabilities of my SATA drives in Ubuntu.
I've tried to install Fedora 11, both 32 and 64 on my main machine.It could not install as it stops on the first install window. I've already filed a bug but really haven't seen any feed back yet.The bug has something to do with Anaconda and the Raid array but I really can't tell.
I have an Intel Board (see signature). I am running intel raid software under W7 currently.It works fine. But, I'm wondering, when I attempt to install F!!, is my current raid set-up causing problems? Do I need to get rid of the intel raid software and use a Fedor/Linux raid program to manage the raid array??
If I have a windows installed in raid-0, then install virtualbox and install all my linux os,s to virtualbox will they be a raid-0 install without needing to install raid drivers?
View 1 Replies View RelatedI have installed Ubuntu on my m1530 since 8.04 and currently dual boot Win7 and 10.10. I would like to dual boot on my PC, but I have run into a problem. I am not a pro at Ubuntu, but this problem I can not solve by reading forums like I have in the past.
I realize this is a common problem, but I have noticed people having success.
I have a M4A87TD EVO MB with two Seagate drives in Raid 0. (The raid controller is a SB850 on that MB) I use the raid utility to create the raid drive that Windows7x64 uses. I have 2 partitions and 1 unused space. Partition 1 is Windows, partition 2 is for media, and the remaining unused space is for Ubuntu.
I am running ubuntu-10.10-desktop-amd64 off a Cruzer 16GB flash drive that was installed via Universal-USB-Installer-1.8.1.4.
My problem like so many others is that when I load into Ubuntu, gparted detects two separate hard drives instead of the raid. I read that this is because kpartx is not installed on 10.10. I then went in LiveCD mode and downloaded kpartx from Synaptic Manager. Gparted still reported two drives. I opened terminal and run a few commands with kpartx. I received an error. (Forgive me I didn't write it down, but I believe it said something about a communication error. I will try again later and see.)
Currently I am reflashing the Cruzer with a persistence of 4GB. I am not familiar with this process, but I understand that my LiveCD boot will save information I download to it. I decided to try this method because I was going to install kpartx and reboot to see if this made a difference.
I am looking for any suggestions on a different method or perhaps someone to tell me that the raid controller or some hardware isn't supported. I did install ubuntu-10.10-alternate-amd64 on my flash drive, but fail to get past detecting my CD-ROM drive since it's not plugged in. If this method is viable, I will plug it in. I also watched the ..... video were a guy creates Raid 0 with the alternated CD, but it wasn't a dual boot and didn't use a raid controller from a MB.
So I decided to build a server using two HDDs and after checking the net I decided to go with Software RAID.Before I mess around and go ahead and buy two 500 GB HDD, I decided to try it out first in virtual box.(my system is F13 64bit with 4GB)
I set up a virtual machine with 2 X 10GB HDD.Mount the live CD (f13 32bit).Run regular install > choose custom layout and do as follows: SDA & SDB will both have Software RAID 500 MB and another software RAID of about 9500 MB I will have md0 /boot (sda1 & sda2 = 500 MB) And another md0 having LVM group loaded with / + SWAP I choose to install boot loader on md0 the first time and I receive the following error when I boot from HDD: FATAL: INT18: BOOT FAILURE I tried installing boot loader on sda same thing.
I just tried to install Fedora 12 x_64 on a machine that is currently running Fedora 11 x_64. It's a new machine for use as a server and is running a Phenom II 4 core on a gigabyte M/B - 4GB RAM, onboard ATI graphics, an Adaptec 5405Z RAID Controller that is in the 16 lane PCIe slot, and 3 SSD SATA dives in a RAID 0.I installed Fedora 11 x_64 on this machine just last week and it went perfectly smooth. The install recognized the video hardware, controller card and the RAID, installed correctly, boots fine, runs solid.When I attempt to install Fedora 12 x_64 on the same machine, it does NOT recognize the controller, nor the RAID and doesn't seem to like the video hardware. I stuck on a floppy drive and made a driver disk from the Adaptec provided Linux drivers, but the install fails to mount the floppy when I try to add the driver during boot from DVD - although it tries. (It's possible that my floppy drive and/or disks are too old to be useful. Seriously, loading drivers from a FLOPPY? Most computers don't even HAVE one any more.Sheesh...). The video also seems squirrelly and works better using the "simple" video drivers.
Anyone got any clues on this. It seems odd that the newer version works less well than the previous one.Maybe I'll try a different .iso - CDs or a live version or something just to check - and maybe try an install on a different machine. Yes, I put the install DVD through the self-test and it passed. I have tried 2 different copies and both fail.LATER - tried with live CD - boots OK, splash screen is OK, after bootup finishes it looks like maybe it's trying to start a different video driver - then the screen goes black and stays that way. Tomorrow I may stick in a discrete video card and see if that makes any difference.
Still Later: I have tried discrete video card, tried moving the RAID controller to the 4 lane slot, tried to install a driver from floppy (still no go) and have tried noprobe on boot command line. Although the "noprobe" got the video to keep going (albeit at a low resolution) it STILL refuses to see the RAID controller. The LED indicators on the RAID card SEEM to be indicating that the card locks up during Fedora 12 boot, but I haven't checked on that just yet. Fedora 11 continues to boot and run fine on the same machine - I'm running it right now. as I type this.Later yet: Ubuntu 9.10 86_64 that was released a couple weeks ago DOES, IN FACT see the controller and the RAID when I run the install process. Looks like Fedora 12 is badly broken after all. (Damn those even numbered releases anyway.....{;>D)=) Guess I'm going to be "stuck" with either Ubuntu or Fedora 11 unless a solution appears pretty soon. I have sent an inquiry to Adaptec, but I'm guessing they are going to say, "we don't support Fedora linux except Fedora 5 and Fedora 6" as those are the only drivers they seem to have available
Friday 11/20 - I've attached a SATA drive to the same computer. By using the "basic" video driver from the install DVD I am able to install F12 to the SATA drive without issue - it installs fine, boots fine, runs fine. However, it still will NOT see the RAID controller. I tried installing the driver .rpm from the disk that came from Adaptec, but the vanilla linux driver doesn't seem to be effective. So far, Fedora 12 continues to be a big FAIL! as far as this particular machine goes.
I've been trying to setup RAID 10 with Fedora 11 on my desktop using this tutorial:[URL].. Everything has been going well, except when following the instructions and getting ready to format, it says I need to define / and boot partitions. This was never included in the instructions.
- LVM Volume Gropus
-- vg_jordan
--- fedoraRAID (type: ext4)
- RAID Devices
-- /dev/md0 (mountpoint/RAID/volume: vg_jordan ; type: LVM)
[Code]...
I want to install Fedora 10 but need to build RAID (bcraid) drivers so the installation will see my RAID array. I'm currently running Fedora 6 & thought this would be the process:
1) Install kernel source
2) Modify configuration to include bcraid drivers.
3) Build new kernel
4) Replace kernel in standard build with custom kernel or load driver during installlation
5) Install Fedora 10
I'm stuck on no. 1. When I tried to install the kernel source, there was some problem with "mockbuild" (wot dat?) which I think was a red herring but I now don't know what to do about these unsatisfied dependencies:
[root@fedora6 ~]# rpm -Vp ~/Desktop/kernel-2.6.27.5-117.fc10.src.rpm
warning: /home/nick/Desktop/kernel-2.6.27.5-117.fc10.src.rpm: Header V3 DSA signature: NOKEY, key ID 4ebfc273
Unsatisfied dependencies for kernel-2.6.27.5-117.fc10.src: rpm-build >= 4.4.2.1-4
[code]....
As I understand, Fedora 12 sets up Intel ICH (when set in BIOS) as mdraid instead of dmraid.I would like to setup my 2 SATA hard drives so ultimately my /boot partition is RAID1, my / (ROOT) partition is RAID 1, and my swap is either RAID0, or fstab referencing 2 partitions on 2 of the drives, both set with pri=0 (which supposedly is equivalent to striping of RAID0, performance wise).
Assuming Fedora 12 uses mdraid for my configuration in either instance, am I better of enabling, or disabling the RAID mode in the BIOS? This system is strictly Fedora--no dual booting, no Windows. Any performance gains; reliability benefits between either scenario?It's a Intel P35 motherboard with ICH9R. Storage configuration is either "AHCI" or "RAID"
I ran into some strange issues with dropping drives with the RAID set on in BIOS. When it was set, that gave me two md devices of md126 (RAID0, swap) and 127 (RAID1 split between / and /boot). I think I had md126p1 for the SWAP, and md127p1 for /boot and md127p2 for / Within purely software, i have:
/dev/sda1 RAID
/dev/sda2 swap
/dev/sda3 RAID
[code]...
I suppose unless the BIOS enabled RAID is supposed to be faster, I'll stick with a purely software route and keep the BIOS set to AHCI.
I've been using Fedora and Ubuntu on a standard PC/laptop (one HDD) for some time, but just as a user. Recently I built a PC with Asus P5K WS motherboard with RAID adapter on board. I've got 5 750GB SATA drives, however hardware restrictions only allows me to create Logical Volume up to 2TB. SO I've created RAID 5 on 3 drives as SysVol and RAID0 on 2 drives for data.
Ran live CD and started to install OS. However I get to point, when system scans for storage devices. It detects smaller volume, but not the SysVol, I want to install the system on. It is offering me to install system on the smaller volume. I've deleted the smaller volume and left one RAID 5 volume and 2 drives. Again the same problem. System detects those 2 drives, but not the volume.
Is there any restriction in Fedora 12 allowing installation on certain LV? Or is it more HW problem?
I am doing a new install and have 4 drives (2x500Gb and 2x2Tb). What I want is the OS on the 2x500Gb and the data on the 2Tb drives. The idea is to make the 500's one RAID 1 set and the 2Tb a RAID 1 set. I think the installer is trying to build the RAID set for the OS but the root is looking like a RAID 0 rather than 1. Is there some way to specify?
View 14 Replies View RelatedI am trying to install FC 10 on my built-in Adaptec raid controller and the Live CD does not see the controller.From my other ATA drive FC10 install I get this from lspci -v:
Code:
00:1f.2 RAID bus controller: Intel Corporation 6300ESB SATA RAID Controller (rev 02) (prog-if 8f)
Subsystem: Super Micro Computer Inc Device 5180
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 18
I/O ports at e200 [size=8]
[code]...
sdb and sdc are the SATA raid disks... they have already been partitioned as a single raid 0 device... not sure why / how they stil show up as two disks.
I upgraded from F10 to F12 using preupgrade. The upgrade itself completed with no errors, but I'm unable to boot afterward.
Symptoms:...Grub starts, the initramfs loads, and the system begins to boot. After a few seconds I get error messages for buffer i/o errors on blocks 0-3 on certain dm devices (usually dm0 and dm2, but I can't get a shell to figure out what those are). An error appears from device-mapper that it couldn't read an LVM snapshot's metadata. I get the message to press "I" for interactive startup. UDEV loads and the system tries to mount all filesystems. Errors appear stating that it couldn't mount various LVM partitions. Startup fails due to the mount failure, the system reboots, and the steps repeat.
Troubleshooting done:...I have tried to run preupgrade again (the entry is still in my grub.conf file). The upgrade environment boots, but it fails to find the LVM devices and gives me a question to name my machine just like for a fresh install. I also tried booting from the full install DVD, but I get the same effect. Suspecting that the XFS drivers weren't being included, I have run dracut to create a new initramfs, making sure the XFS module was included. I have loaded the preupgrade environment and stopped at the initial GUI splash screen to get to a shell prompt. From there I can successfully assemble the raid arrays, activate the volume group, and mount all volumes -- all my data is still intact (yay!). I've run lvdisplay to check the LVM volumes, and most (all?) appear to have different UUIDs than what was in /etc/fstab before the upgrade -- not sure if preupgrade or a new LVM package somehow changed the UUIDs. I have modified my root partition's /etc/fstab to try calling the LVM volumes by name instead of UUID, but the problem persists (I also make sure to update the initramfs as well). From the device-mapper and I/O errors above, I suspect that either RAID or LVM aren't starting up properly, especially since prior OS upgrades had problems recognizing RAID/LVM combinations (it happened so regularly that I wrote a script so I could do a mkinitrd with the proper options running under SystemRescueCD with each upgrade).
I have tried booting with combinations of the rootfstype, rdinfo, rdshell, and rdinitdebug parameters, but the error happens so early in the startup process that the messages quickly scroll by and I just end up rebooting.
System details:4 1-TB drives set up in two RAID 1 pairs. FAT32 /boot partition RAIDed on the first drive pair. Two LVM partitions -- one RAIDed on the second drive pair and one on the remainder of the first drive pair. Root and other filesystems are in LVM; most (including /) are formatted in XFS.
I've made some progress in diagnosing the issue. The failure is happening because the third RAID array (md2) isn't being assembled at startup. That array contains the second physical volume in the LVM volume group, so if it doesn't start then several mount points can't be found.
The RAID array is listed in my /etc/mdadm.conf file and identified by its UUID but the Fedora 12 installer won't detect it by default. Booting the DVD in rescue mode does allow the filesystems to be detected and mounted, but the RAID device is set to be /dev/md127 instead of /dev/md2.
The arrays are on an MSI P35 motherboard (Intel ICH9R SATA chipset) but I'm using LInux software RAID. The motherboard is configured for AHCI only. This all worked correctly in Fedora 10.
my setup
P4 3.4GHZ
2GB Ram
Gigabit Ethernet
Drive Configuration
1 x 750GB Sata
Connected To My Raid Controller in ide mode
1 x 120GB IDE HDD
1 x 250GB IDE HDD
my problem, I Am trying to install f12 and the only drive that it sees is the 750GB Sata,it is not seeing the other 2 ide drives The raid controller is an ite 8212 in ide mode The Bios Sees the drives just F12 doesnt
I just bought two 320GB SATA drives and would like to install F11 with software RAID 1 on them. I read an article which explains how to install RAID 1, but it used 3 disks: one for OS and two clones. Do I really need a third disk to install RAID 1 configuration? If 2 disks is enough, then should I select "Clone a drive to create a RAID device" during F11 installation as explained here?
View 6 Replies View RelatedCurrently running F10 on a RAID1 software raid array in Linux (not hardware or BIOS). I used the F13 install disk to boot and selected install/upgrade. Problem is that the Anaconda portion never sees the RAID device.
I tried passing the "nodmraid" argument to the kernel during boot. Other research suggested that the auto=md switch should be appended to the mdadm.conf file. No results from either solution.
Anaconda does not see the /dev/md0 or /dev/md1 and consequently it only offers an installation option.
What I would prefer is to upgrade.
Could any RAID gurus kindly assist me on the following RAID-5 issue?I have an mdadm-created RAID5 array consisting of 4 discs. One of the discs was dropping out, so I decided to replace it. Somehow, this went terribly wrong and I succeeded in marking two of the drives as faulty, and the re-adding them as spare.
Now the array is (logically) no longer able to start:
mdadm: Not enough devices to start the array.Degraded and can't create RAID ,auto stop RAID [md1]
I was able to examine the disks though:
Code:
root@127.0.0.1:/etc# mdadm --examine /dev/sdb2
/dev/sdb2:
Magic : a92b4efc
Version : 00.90.00
code....
Code:
mdadm --create --assume-clean --level=5 --raid-devices=4 /dev/sda2 /dev/sdb2 /dev/sdc2 /dev/sdd2
As I don't want to ruin the maybe small chance I have left to rescue my data, I would like to hear the input of this wise community.
I have a fancy new Quad Core Xeon machine here that I'm trying to install F10 x64 on. The installation went fine. When it reboots the first time, though, I get the dreaded Error Loading OS.
So I dug up my bookmark of the awesome Grub HOWTO here and followed the steps to install Grub manually. Alas, I get the same result after installing it. Even tried doing a makeactive (hd0) just in case, but no luck.
I did more searching and searched for "raid install" but didn't find anything helpful. So here I am... hoping somebody has some insight.
Am installing Fedora 10 on an old but good server that used to be a windows box. It has 2 sata disk raid level 1 on adaptec 2410SA card. Disks are clean no info even did a low level format and recreated RAID.. twice DVD boots and installs os on raid array and reports success. new volume appears under computer icon but cannot be mounted after reboot attempt reports Reading physical volumes. This may take a while... (it doesn't)
Volume group "VolGroup00" not found
Unable to acces resume device (/dev/VolGroup00/LogVol01)
mount: error mounting /dev/root on /ysroot as ext3: No such file or directory
input: PS/2 Generic Mouse as /devices/platform/i8042/serio1/input/input4
and then a blinking cursor with keyboard echo but its just copying reboot with install DVD does not show previous (unmountable) disk image and repeat of above process increases operator need for alcohol have "disable write cache for drives" as I found that is a post but after fedora install.I do not know what grub is for instance but once linux is booted (on other computers) I can muddle through ok in terminal mode.
I installed Fedora 12 and performed the normal updates. Now I can't reboot and get the following console error message.
ERROR: via: wrong # of devices in RAID set "via_cbcff jdief" [1/2] on /dev/sda
ERROR: removing inconsistent RAID set "via_cbcff jdief"
ERROR: no RAID set found
No root device found
Boot has failed, sleeping forever.
It's been a real battle, but I am getting close.I won't go into all the details of the fight that I have had, but I've almost made it to the finish line. Here is the set up. ASUS Z8PE-D18 mother board 2 CPU, 8 Gig Ram. I recently added an OCZ Agility SSD, defined a raid 1 virtual disk on the 1 terabyte WD HDD drives, which will holds all of my user data, the SSD is for executables.The bios is set to AHCI. Windows 7 installed fine, recognizes the raid VD just fine.
I installed Ubuntu 10.04 by first booting into try and mode, then opening a terminal and issuing a "sudo dmraid -ay" command. Then performing the install. I told it to install the raid components, and told it to let me specify the partitions manually. When setting up the partitions, I told it to use the free space I set aside on the SSD from the Windows 7 install as ext4 and to mount root there. Ubuntu installed just fine, grub2 comes up just fine, and Windows 7 boots with out a hitch, recognizing the mirrored partition as I indicated previously. When I tell grub to boot linux however, it pauses and I get the "no block devices found" message. It will then boot, but it does not recognize the raid array. After Ubuntu starts up I can run "dmraid -ay" and it recognizes the raid array, but shows the two component disks of the raid array as well. It will not allow the component disks to be mounted, but they show up which is annoying. (I can live with that if I have to)
I have fixed a similar problem before by setting up a dmraid script in /etc/initramfs-tools/scripts/local-top ... following the instructions found at the bottom of this blog:[URL].. To recap: My problem is that after grub2 fires up Ubuntu 10.04.1 LTS (Lucid Lynx), it pauses, and I get "no block devices found" It then boots but does not recognize the raid array untill I manually run "dmraid -ay". I've hunted around for what to do but I have not found anything. It may be some timing issue or something, but I am so tired of beating my head against this wall.
Installing new Intel server S5000VSA (Sapello) motherboard with RAID 1. Downloaded F10 32 bit DVD and run install. Everything works fine and select Samba and all that. Install completes but on reboot get a blank screen.
I know with Windows one has to load the RAID driver off the Intel driver CD, so guess that is the problem. But how do I do this in Fedora? Question: How do I get to select the Intel RAID driver in the install process? There does not seem to be any place to stop and make this selection. I tried selecting the Red Hat and Suze installs on the Intel configuration assistant but it then reboots and that is it. In Windows it would ask to insert the Intel driver CD but that does not happen. So I am stuck. I loaded Fedora some 3 year ago and like it but then it was not on a RAID setup. I created a VMWare install on my desktop and did the same install options and it works. So the DVD seems fine.
I'm attempting to install F13 on a server that has a 2-disk RAID setup in the BIOS. When I get to the screen where I select what drive to install on, there are no drives listed. The hard drives were completely formatted before starting the 13 installation. Do I need to put something on them before Fedora will install?
View 3 Replies View RelatedMy System Intel Core Duo E5300 Mobo - Gigabyte G31M-ES2L 1GB DDR2 800MHz RAM 4 x WD20EARS HDD I have been trying to install Fedora or Ubuntu for over a week. I thought it would take an hour and i would be away. I have been trying to install using the mdadm Software RAID feature. Everytime it takes about a day to format the drives and then i get an installation error. The drives state they are ready to use as is on any operating system other then WinXP, but this does not appear to be the case.
I am very new to Fedora... I have been doing some reading.[URL].. That information has been promising. I have been able to get into Fdisk off the live CD but i can't figure out how or if it is possible to do what i want it to.
Has anyone had any luck getting these drives to function correctly in a software RAID? I have had good luck with WD drives in the past and just assumed these drives would do what i wanted to but alas i have been proven wrong.
The partitions i wanted was...
- A 2GB swap parition
- A 10 GB RAID 1 partition for Fedora
- The remaining space as a Raid 5 for files.
Am i just banging my head against a wall here, or is this possible.
I tried to boot from a Fedora 12 installation DVD. In the "Welcome to Fedora 12!" screen, my USB keyboard and mouse do not work. However, they work after the welcome screen and I can complete the installation.
I set my hard drives to be RAID 1. After the installation, the machine reboot. However, it halt on. I would follow the steps as shown in "http://ping.co.il/node/1/" to solve this problem, but the USB keyboard does not work in the "Welcome to Fedora 12!" screen. I cannot select the rescue mode. How can I solve this problem?
I have been battering with FC10 and software RAID for a while now, and hopefully I will have a full working system soon. Basically, I tried using the F10 live CD to setup Software RAID 1 between 1 hard drives for redundancy (I know its not hardware raid but budget is tight) with the following table;
[Code]....
I set these up by using the RAID button on the partition section of the install except swap, which I set-up using the New partition button, created 1 swap partition on each hard drive that didn't take part in RAID. Almost every time I tried to do this install, it halted due to an error with one of the raid partitions and exited the installer. I actually managed it once, in about...ooo 10-15 times of trying but I broke it. After getting very frustrated I decided to build it using just 3 partitions
[Code]....
I left the rest un-touched. This worked fine after completing the install and setting up grub, reboot in to the install. I then installed gparted and cut the drive up further to finish my table on both hard drives. I then used mdadm --create...etc to create my RAID partitions. So I now have
[Code]....
