CentOS 5 Networking :: Ifcfg-eth0 Rewritten On Each Boot After Upgrade To 5.3 From 5.2
May 12, 2009
I have just upgraded a CentOS 5.2 box to Centos 5.3
I did have a bridged networking setup for Virtualbox which worked well. eth0 was bridged with br0. br0 boot protocol was DHCP and it sent its DHCP_HOSTNAME to the windows DHCP servers.
since the upgrade the br0 does not get an address but the eth0 does. I found that the scripts in /etc/sysconfig/network-scripts/ifcfg-* are getting rewritten.
I figure I may not need to have a bridge any more so I stripped that out to try to get a simple network setup working. I now just have eth0. I edited /etc/sysconfig/network-scripts/ifcfg-eth0 so that it looked like this,
~]# cat /etc/sysconfig/network-scripts/ifcfg-eth0
# Attansic Technology Corp. L1 Gigabit Ethernet Adapter
DEVICE=eth0
BOOTPROTO=dhcp
[Code].....
View 3 Replies
ADVERTISEMENT
Jun 1, 2011
When I do service network start it is giving me the error grep : can not find directory ifcfg-ifcfg-eth0....
For some reason it is adding another ifcfg to my ifcfg-eth0 file.
View 1 Replies
View Related
Mar 18, 2009
I've been racking my brains over the past few days trying to figure out why my NIC card (network interface card) won't show up in the ifcfg-eth0 file.When I configure a new server (like this one) I always go to:/etc/sysconfig/network-scripts/ifcfg-eth0 and from there I usally see the name of my NIC's manufacturer's name and the hardware MAC address.Then it's only a simple process of entering the server's IP address, netmask and gateway and I'm up and running in no time...But not in this case! the ifcfg-eth0 file is completely blank! There's not ONE single line of config info in it... (?)The server runs an Intel core 2 duo (dual-core) CPU with 1 gig of RAM.
I've even re-formatted the drive and re-installed Centos 5.1 on the darn thing 3 times and it simply won't work.The server cannot resolve when I do a wgetIt also gives me a 'resolution problem in the named configuration'.What I don't understand is that the 2 small LEDs on the Cat 5 cable lights up and flash at what appear to be regular intervals here.
View 6 Replies
View Related
Jun 11, 2009
When I setup the server I added multiple ips. Now that I need to edit ip info I can't find any alias files in the network-scripts folder. But restarting server the ips work fine. Is there some where else that this would be stored.
View 2 Replies
View Related
Jul 12, 2010
I run a VMware clone of CentOS 5.3, I observe that kudzu [i.e. /etc/init.d/kudzu, from /etc/rc3.d/S05kudzu or /etc/rc5.d/S05kudzu] detects a MAC address change on eth0 and then creates a /etc/sysconfig/network-scripts/ifcfg-eth0.bak file. This .bak file is identical to the original ifcfg-eth0 file except for the value of the HWADDR [i.e. MAC address] parameter. I would be unconcerned but for the fact that /usr/bin/neat indicates that both ifcfg-eth0 AND ifcfg-eth0.bak are 'Active'. The following solution may help others with the same (or similar) problem:
[Code]...
View 4 Replies
View Related
Jun 9, 2010
I am having a problem when creating alias in Fedora Core 10. When i create a file like "ifcfg-eth0:1" and put contents in it like
DEVICE=eth0:1
BOOTPROTO=static
IPADDR=ip addrss
Netmask=Netmask
and when i save settings and restart with "service network restart" the network card does not create any alias like eth0:1 instead it replace the original ip address of eth0 with the ip address i given to eth0:1. So i want to keep both network ips of eth0 and eth0:1.
View 3 Replies
View Related
Jul 20, 2011
I have using fedora 10 on IBM Z60m Laptop, and my eth0 is not been up even is "ONBOOT=yes" in /etc/sysconfig/network-scripts/ifcfg-eth0. why I have to make it up every time
View 1 Replies
View Related
Mar 9, 2011
how to remove the network alias (ex: ifcfg-eth0:2)from RHEL5, i had deleted the ifcfg-eth0:2 file from /etc/sysconfig/network-scripts/ifcfg-eth0:3but i can still see the entry in the graphical network configuration after i issued the command system-config-network, i want to remove it from there.
View 3 Replies
View Related
Apr 17, 2011
I'm nearly at the end of creating a shell script that automates changing network settings by prompting the user for desired settings, then applying them.
In the course of my development, I created temporary copies of /etc/sysconfig/network-scripts/ifcfg-eth0 (/etc/sysconfig/network-scripts/ifcfg-eth0_tmp1, for example) so as to not alter the original file. Little did I know that on boot the system would attempt to load each of these kinds of files and associate it with an ethernet connection, in this case eth0.
So..... now there are multiple copies in the /etc/sysconfig/network-scripts diretory that essentially have the same settings. They are..
/etc/sysconfig/network-scripts/ifcfg-eth0
/etc/sysconfig/network-scripts/ifcfg-eth0_tmp1
/etc/sysconfig/network-scripts/ifcfg-eth0_tmp2
Now when the system boots, it attempts to load them all. The boot doesn't appear to complete, and I can't ping, login, or otherwise access the system through convention routes (putty, etc.).
The easy solution would be to delete the tmp files and reboot. Now, how do I do that without being able to log in to the server. It's a VM by the way, if that makes a difference.
View 7 Replies
View Related
Jan 18, 2011
I set up a bridge device but I can not figure out how to pass parameters into the ifcfg-vmbr0 in particular I need to pass:
maxage
ageing
fd and stp seems to be passed by DELAY=0 and STP=on the others? I have not found anything in the post, tips, docs how could I do?
View 1 Replies
View Related
Dec 26, 2010
i install kernel rpm after i boot that kernel network not working kernel name : kernel-rt-trace-2.6.24.7-132.el5.centos.i686 [URL] error "Bringing up interface eth0: Device eth0 has different MAC address than expected, ignoring."
View 1 Replies
View Related
Apr 22, 2011
im trying to setup eth0 with subdevice eth0.0 and eth0.99 to come up at boot
eth0 is dhcp clint
eth0:0 is static ip
eth0.99 is 802.1q vlan interface
/etc/network/interfaces
Code:
auto lo
[Code]....
View 1 Replies
View Related
Dec 31, 2010
Running CentOS5.4 on home-build.The wireless card setup is working,at least with regard to internet access through a Linksys router.Trying to set up Windows shares using SAMBA has been problemmatic. After many searches the ifcfg file seems to be a mystery. So what is meant by the "ADDRESS0=" in the ifcfg-wlan0 file. it is the ""the NETWORK that matches the NETMASK". But even that I cannot quite understand (apparently) as my efforts to enter different items in this file have all failed.
View 5 Replies
View Related
Jan 21, 2010
Running CentOS5.4 on home-build. The wireless card setup is working, at least with regard to internet access through a Linksys router. Trying to set up Windows shares using SAMBA has been problemmatic. After many searches the ifcfg file seems to be a mystery. So what is meant by the "ADDRESS0=" in the ifcfg-wlan0 file. Searches suggest it is the ""the NETWORK that matches the NETMASK". But even that I cannot quite understand (apparently) as my efforts to enter different items in this file have all failed.
View 19 Replies
View Related
Jan 11, 2010
This on a Vostro 1220 Laptop w/ Intel 5300 wireless:
A.I have long boot up time.I think it's because of the eth0 network search which I don't use.I have an intel wireless 5300 card running.How can I speed up the boot time, i.e. disable or change the eth0 at boot, the searching?
B:When I restart or shutdown, the screen flashes repeatedly and gets some garbled colors along the top before finally rebooting looks like windows ME or something).This vostro has an intel x4500HD vid chipset in it.
C.How do I get into gnome configuration editor to turn on Metacity compositing? Alt-F2 and run gconf-editor doesn't do it. I don't do compiz, but need compositing.
D.I need to install Chromium Browser as it sync my bookmarks.I have RPMforge enabled btw also...how can I do that? I.e. rpm repo for chromium?
This will help me get off to a running start so I can get up to speed on CentOS..
View 3 Replies
View Related
Dec 1, 2009
my rounter causes puppy to write an improper dns entry in resolv.conf. Consequently I have to manually write it, then I have to place a command on it to make sure it doesn't get rewritten on boot, or after a couple of hours use. I had this problem with xubuntu as well.
[URL]
I solved this problem in ubuntu by using the chattr command.
[URL]
Puppy won't let me do this. When I use the chattr +i /etc/resolv.conf, it gives me this error. chattr: Inappropriate ioctl for device while reading flags on /etc/resolv.conf I tried chmod 444 but it had no effect on reboot. resolv.conf was rewritten again. How can I make sure this file does not get rewritten. Why won't chattr work?
View 11 Replies
View Related
Apr 28, 2009
I'm running a fresh install on an intel i7 system on an asus p6t deluxe v2 motherboard with the onboard NIC (Marvell Technology pci-e). I know the NIC is working as when I boot into the onboard OS that Asus provides (Asus Express Gate SSD)I have a working net connection.Booting up CentOS hangs at determining IP information for eth0 and eventually fails with the following error:PING xxx.170.30.1 from xxx.170.31.231 eth0: 56(84) bytes of data---xxx.170.30.1 ping statistics ---4 packets transmitted, o received, +3 errors, 100% packet loss, time 2999ms, pipe 3 failed.
RTNETLINK answers: file exists.
RTNETLINK answers: file exists.
RTNETLINK answers: file exists.
[code]....
View 14 Replies
View Related
Apr 5, 2010
i have 5.4 installed on a super-micro server motherboard (has two gigabit ether ports). when i boot while its initializing everything it gets to the "starting eth0" and just stays there?
right before it boots up and says press any key for options i press a key and choose "centos (2.6.18-164.el5)" and it boots up fine but when i choose "centos (2,6,18-164.el5xen)" the problem occurs. and that is the default boot option.
View 3 Replies
View Related
Jun 14, 2010
I have a similar problem. My eth0 also disappeared after an upgrade to Ubuntu 10.04, and didn't come back after downgrading back to 9.10. The LEDs on my ethernet port are *not* flashing. Does this mean my network card is dead, or is there any hope I can get back online?
View 9 Replies
View Related
Aug 13, 2010
I'm having the same Harker2010 's problem.Running 10.04 LTS on a Dell latitude D-820, and switching between lan and wifi worked OK until last upgrade.Harker2010's screenshots are also valid for my problem. I've tried everything I see on this post but the problem still there.
View 1 Replies
View Related
Mar 4, 2009
how can i activate eth0 on terminal ?
View 1 Replies
View Related
Dec 21, 2010
Installed Centos 5 on IBM T60P laptop. Intel 82573L Gigabit ethernet controller. Keep getting this erro message, "e1000 device eth0 does not seem to be present, delaying initialization."
View 3 Replies
View Related
May 7, 2009
Centos 5.3 How can I change the primary nic from eth1 to eth0? My board has 2 nic's and I'm having license issues with cpanel
View 2 Replies
View Related
Oct 7, 2009
I have been running into network issues lately with my CentOS 5 (installed on AMD Athlon X2 - 64 bit machine about 2 years ago). It was able to connect to the network fine until yesterday when I installed more memory into the machine restarted it.
Upon restart, the boot up was paused at 'Determining IP information for eth0' step for a while and booted with out connecting to the network. I tried restarting the network (/sbin/service network restart), but this is the error message I continuously get: Determining IP information for eth0...PING xxx.1.226.1 (xxx.1.226.1) from xxx.1.226.83 eth0: 56(84) bytes of data
[Code]...
View 2 Replies
View Related
Jan 18, 2010
I have a Proliant DL 120 G5 with CentOS 5.4 and I have installed a Brodcom Corporation Netxtrem BCM 5722 Gigabit Ethernet PCI. So I have two interfaces: eth0 broadcom eth1 Intel The eth1 works, instead eth0 don't work. I can ping itself and 127.0.0.1 but I can't ping the gateway. The results of netstat -nr is:
[code]....
View 1 Replies
View Related
Apr 1, 2010
I've seen this pop up a few times on the forum but my setup is slightly different. I have a PC with an ASUS P5N32-SLI Premium motherboard. I've just installed CentOS 5.1. Yes, I know this is ancient, but this is what they're developing on at work. I'm trying to get connected either via ethernet or wireless and neither one works. When I boot the computer to Window XP it does connect on ethernet. Ethernet should be easy so I'm concentrating on that. But I get "Determining IP information for eth0... failed." after a 'service network start'.Here is some other information that was asked on similar threads:
> uname -rmi
2.6.18-53.el5 x86_64 x86_64
> grep eth0 /etc/modprobe.conf
[code]....
View 4 Replies
View Related
Jul 8, 2010
New to CentOS5.5 I'm experiencing some trouble in order to continue my configuration. I've just installed my vmware tools and configured my network card with system-config-network
Edit eth0 (eth0) - vmxnet3 -> with a static IP I rebooted my server and since then I lost my eth0. I still see it in system-config-network, but I can't active it anymore.:
/etc/init.d/network start Bringing up interface eth0: Device eth0 has different MAC address than expected, ignoring. [FAILED]
View 2 Replies
View Related
Oct 18, 2010
I'm having a problem and despite I have googled a lot cant find the root cause. I have a server with two embedded NICs and centos 5.5 loaded. I need to have one NIC with a fix internal IP address to communicate with the intranet and a second NIC with a fix address from my telephone provider. I know I cant have two different gateways on the net so I configured only the gateway for the second NIC leaving the field empty for the first.
I found that the first NIC is handling all the traffic for both interfaces (eth0 and eth1) and the second NIC is in standby (or doing nothing). This is causing the traffic intended for the second NIC never reach their destination. After a couple days working with the BIOS and other configuration files I tried another way of solve the issue. I put a fix address for the first NIC and another fix address for the second NIC (both in the same subnet) and from a computer pinged successfully both addresses. However if I disconnect the cable for the first NIC both interfaces goes down (eth0 and eth1) and both pings fails. If I disconnect the cable for the second NIC (with the first one connected) both pings still running without any disturbance.
I worked also in a second server with different hardware (different kind of motherboard, different NIC manufacturer, etc.) but the problem is also present in this second server. I was reading about NIC bonding or teaming, but this configuration is not present in the modprobe.conf or in the ifcfg-eth0 files, so I believe the problem is not related with this feature. Do you know what is happening with the NICs and how can I get two really, fully independent NICs?
View 7 Replies
View Related
Nov 8, 2010
I have 2 network interface on 1 server and i got a problem finding a solution for it.I have 1 java application and i want it to use the eth1 for that application and not the default eth0. On eth0 i got for example xx.xxx.xx.22 and on eth1 i got xx.xxx.xx.23 and i want the java app to use the 23 ip one.
View 3 Replies
View Related
Nov 23, 2010
I am currently working to get to a stable dual boot Win7/CentOS 5.5 configuration on a Dell Latitude E6510 with the Intel 82577LM chipset. I haven't gotten the Centrino N WiFI chipset working yet, but the Eth0 device was working just fine.However, yesterday I did a system update. I did not pay close attention, but I believe the update did mention networking, because I thought it might help me get my wireless going. Now, Eth0 fails with the message, "Determining IP information for eth0... failed; no link present. Check cable?" It does this at boot up and if we try reactivating it once the system is up. We have tried unstalling and re-installing the driver.The Window 7 boot sees the adapter and runs just fine. I was at a different site location yesterday when everything was working, but my co-workers and I can't help but think it might be related to the update yesterday, since everything worked prior to the update and Windoze 7 works fine with the adapter.
I have not been able to mount my NTFS harddrive on the CentOS side, despite installing fuse, and I don't have wireless, which makes it difficult to get access to new drivers. I also have a FAT32 partition that would be great to share between the boots for passing info, but I haven't found a way to mount a FAT32 partition in CentOS.
View 6 Replies
View Related
